Instruction d'utilisation Emerson Process Management

Résumé du contenu de la page N° 1

WHAT YOU SHOULD KNOW BEFORE YOU BEGIN
Connecting the dispenser to your regular water supplies requires no special
plumbing. All details are covered in the installations instructions. Be sure
that the plumbing connections conform to your applicable local codes. If your
water supply contains sand, grit or other suspended particles, the use of a
filter is recommended. The filter should not result in the water pressure to
Division of Emerson Electric Co.
Racine, Wisconsin 53406, U.S.A.
the dispe

Résumé du contenu de la page N° 2

HOW YOUR HOT WATER DISPENSER WORKS Water is electrically heated to near-boiling (190˚F/88˚C) in a compact tank that mounts under the sink. A thermostat maintains it at this approximate temperature. When you turn the handle, cold water enters the tank and forces hot water out of the faucet. The system is vented so the tank is not pressurized. Due to the unique operation of your instant Hot Water Dispenser, you may experience a slight delay in the dispensing of water after the handle is actuated.

Résumé du contenu de la page N° 3

INSTALLATION INSTRUCTIONS 1 IF YOU WISH TO USE THE HOLE IN WHICH THE SPRAY HOSE IS LOCATED, FOLLOW THESE EASY STEPS: 4 3 2 1. Turn off water supply 2. Remove nut that connects spray hose at bottom of faucet. 3. Remove nut that connects spray hose at bottom of washer flange in spray hole using ordinary wrench or basin wrench. 4. Plug faucet tube opening with either a 1/8" plug or a 1/4" cap (not supplied) 1 What if you don’t use a sprayer hole? You can cut a mounting hole through a stainless ste

Résumé du contenu de la page N° 4

5 CONNECT WATER TO DISPENSER HEAD – H770, H990, GN C 1. Before you start open the shutoff valve and let a small amount of water A run through it into the pan. This will flush the line of any sediment. B 2. When connecting to a compression type fitting (tee or valve), remove the nut and ferrule (a rounded brass fitting) from the valve. Then place the nut followed by the ferrule over the end of the LONGEST copper tube coming from the dispenser head. (A): Nut (B): 1/4" copper tube (C): Ferrule 5

Résumé du contenu de la page N° 5

9 MAKE FINAL PLUMBING CONNECTIONS Product Damage • Make sure bends in all tubes are smooth and unkinked before you proceed. • Make sure all tubes are not twisted, pinched or blocked. • Do not extend the two water lines to the tank beyond the 16" (40cm) provided. • Pinched or blocked water lines may cause access pressure and damage the dispenser tank. 1. Slip plastic nut over 1/4" copper inlet tube. Insert tube into threaded inlet fitting until you feel it stop. Be sure copper tube is straight.

Résumé du contenu de la page N° 6

USE ADJUSTING TEMPERATURE Electric Shock Hazard • To prevent electrical shock, disconnect power before removing access cover to adjust or service the thermostat. Scalding Hazard • Do not allow water to boil. May result in severe burns. Fire / Product Hazard • Do not remove or alter the thermal overload protector. May result in product damage or fire. Temperature Adjustment Access cover Figure 1 Figure 2 The thermostat is factory pre-set at approximately 190˚F (88˚C). If the SEASONAL STORAGE t

Résumé du contenu de la page N° 7

TROUBLESHOOTING GUIDE Problem Possible Cause What to do Unit not plugged in or electric out- Check that the unit is connected to a properly grounded electric outlet and that Water is not hot let is inoperative. circuit breakers or fuses are in good order. Thermal overload protector has Contact your In-Sink-Erator dealer for service. tripped Thermostat not adjusted to your Adjust thermostat. See Adjusting Temperature. Water too hot or not hot taste enough Low water pressure preventing the Unplug

Résumé du contenu de la page N° 8

IN-HOME SERVICE WARRANTY WARRANTY DURATION: In-Sink-Erator provides a full one (1) year warranty from the date of manufacture or the date of purchase with supporting receipt. If the unit is professionally installed, the warranty is one (1) year from the date of installation with supporting receipt. WARRANTY COVERAGE: The In-Sink-Erator In-Home-Service warranty provides replacement parts and labor to correct defects in material or workmanship in the dispenser. If warranty service is required, c