Résumé du contenu de la page N° 1
®
Model 5600 & 5600 Econominder
Service Manual
IMPORTANT: Fill in pertinent information on page 3 for future reference.
Résumé du contenu de la page N° 2
® Model 5600 & 5600 Econominder Table of Contents Job Specification Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 General Residential Installation Check List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Valve Installation and Start-up Procedures . . . . . . . . . . . . . . . .
Résumé du contenu de la page N° 3
® Model 5600 & 5600 Econominder Job Specification Sheet Job Number ___________________________________ Model Number ________________________________ Water Test ____________________________________ Capacity of Unit ________________________ Max. _____________ Per Regeneration Mineral Tank Size: Diameter ___________________ Height _____________________ Brine Tank Size and Salt Setting Per Regeneration: ___________________________________ Control Valve Specifications Type of Timer: ___ Std.
Résumé du contenu de la page N° 4
® Model 5600 & 5600 Econominder General Residential Installation Check List Water Pressure A minimum of 25 lbs of water pressure is required for regeneration valve to operate effectively. Electrical Facilities An uninterrupted alternating current (A/C) supply is required. Please make sure voltage supply is compatible with unit before installation. Existing Plumbing Condition of existing plumbing should be free from lime and iron buildup. Replace piping that has heavy lime and/or iron build-u
Résumé du contenu de la page N° 5
® Model 5600 & 5600 Econominder Valve Installation and Start-up Procedures 1. Place the softener tank where you want to install the unit. NOTE: Be sure the tank is level and on a firm base. 2. During cold weather it is recommended that the installer warm the valve to room temperature before operating. 3. Perform all plumbing according to local plumbing codes. — Use a 1/2" minimum pipe size for the drain. — Use a 3/4" drain line for backwash flow rates that exceed 7 gpm or length that exceeds 2
Résumé du contenu de la page N° 6
® Model 5600 & 5600 Econominder Model 5600 Installation and Start-up Procedures NOTE: Install the water softener with the inlet, outlet and drain connections made according to manufacturer’s recommendations and to meet applicable plumbing codes. Manual Regeneration Knob 24-Hour Gear Skipper Wheel (shows every Red Time other day Button Set regeneration) Time of Day Arrow Red Pointer Figure 1: Model 5600 Softener Control 1. Manually index the softener control into the In Service position and let
Résumé du contenu de la page N° 7
® Model 5600 & 5600 Econominder Model 5600 Backwash Filter Installation and Start-up Procedures NOTE: Install the water softener with the inlet, outlet and drain connections made according to manufacturer’s recommendations and to meet applicable plumbing codes. Manual Regeneration Knob 24-Hour Gear Skipper Wheel (shows every Red Time other day Set Button backwash) Time of Day Arrow Red Pointer Figure 2: Model 5600 Backwash Filter Control Before Plugging in the Unit 1. Open a treated water tap d
Résumé du contenu de la page N° 8
® Model 5600 & 5600 Econominder Model 5600 Backwash Filter Installation and Start-up Procedures (Cont’d.) Cycle Times and Flow Diagrams 1. In Service position. See Figure 4, page 10. 2. Preliminary Rinse position. — Same as Figure 4, page 10 with standard piston (white end plug) or filter piston (black end plug). — Eliminated with low water piston (gray end plug). 3. Backwash position. — Same as Figure 6, page 11 with standard piston. — 15 minutes with filter piston. — 7 minutes with low water
Résumé du contenu de la page N° 9
® Model 5600 & 5600 Econominder Model 5600 Econominder Installation and Start-up Procedures NOTE: Install the water softener with the inlet, outlet and drain connections made according to manufacturer’s recommendations and to meet applicable plumbing codes. Manual Regeneration Knob 24-Hour Gear Program Wheel People Dial Red Time Set Button Grains Per Gallon Water Hardness Scale White Dot Gallons Label Figure 3: Model 5600 Econominder 1. Manually index the softener control to the In Service posi
Résumé du contenu de la page N° 10
® Model 5600 & 5600 Econominder Water Conditioner Flow Diagrams Service Position Figure 4: Service Position Preliminary Rinse Position Figure 5: Preliminary Rinse Position 10
Résumé du contenu de la page N° 11
® Model 5600 & 5600 Econominder Water Conditioner Flow Diagrams (Cont’d.) Backwash Position Figure 6: Backwash Position Brine Position Figure 7: Brine Position 11
Résumé du contenu de la page N° 12
® Model 5600 & 5600 Econominder Water Conditioner Flow Diagrams (Cont’d.) Slow Rinse Position Figure 8: Slow Rinse Position Second Backwash Position Figure 9: Second Backwash Position 12
Résumé du contenu de la page N° 13
® Model 5600 & 5600 Econominder Water Conditioner Flow Diagrams (Cont’d.) Settling Rinse Position Figure 10: Settling Rinse Position Brine Tank Fill Position Figure 11: Brine Tank Fill Position 13
Résumé du contenu de la page N° 14
® Model 5600 & 5600 Econominder Model 5600 Control Valve Drive Assembly 1 29 27 20 1A 16 15 19 1A 22 5 13 12 38 14 34 37 39 21 7 8 6 9 2 30 35 25 3 5 4 23 11 26 28 5 Figure 12: Model 5600 Control Valve Drive Assembly 14
Résumé du contenu de la page N° 15
® Model 5600 & 5600 Econominder Model 5600 Control Valve Drive Assembly Item Number No. Req’d Part Number Description 1 1 14448-010 housing, with pin 1 14448-011 housing, with pin drilled for screw 1 14448-012 housing, with pin drilled for thumb screw 1A 1 15494-01 “L” housing, with pin 1 15494-03 “L” housing, with pin drilled for designer 2 1 13175 motor mounting plate 3 1 18743 motor, 120V, 60 Hz 1 19659 motor, 24V, 60 Hz 4 (2-3) 11384 screw, motor mtg. and ground wire 5 (3-5) 13296 screw, com
Résumé du contenu de la page N° 16
® Model 5600 & 5600 Econominder Model 5600 and 5600 Econominder Control Valve Drive Assembly 48 47 Backwash Filter Injector Option 10 49 50 55 20 12 22 11 23 21 42 9 43 26 8 39 53 2 14 52 7 34 33 32 2 29 3 31 20 16 15 1 30 17 46 27 16 28 20 51 22 18 24 19 23 42 21 4 43 26 45 5 39 40 38 41 44 52 37 14 36 35 Figure 13: Model 5600 and 5600 Econominder Control Valve Drive Assembly 16
Résumé du contenu de la page N° 17
® Model 5600 & 5600 Econominder Model 5600 and 5600 Econominder Control Valve Drive Assembly Item Number No. Req’d Part Number Description 1 2-4 13255 adapter clip (clock or meter) 2 5 13242 seal 5 17772 silicone seal 3 1 61400-12 valve body assembly, 1 ″ dist. 1 61400-11 valve body assembly, 3/4 ″ dist. 4 1 13304 o-ring, distributor tube, 1 ″ 1 10244 o-ring, distributor tube, 13/16 ″ 5 1 12281 o-ring, top of tank 6 6 not assigned 7 4 14241 spacer 8 1 13247 piston, standard 1 13781 piston, low w
Résumé du contenu de la page N° 18
® Model 5600 & 5600 Econominder Model 5600 Econominder Control Valve Drive Assembly 29 1 27 19 1A 20 18 21 13 12 34 42 16 15 7 14 8 6 9 44 43 2 3 4 28 25 35 5 45 30 5 11 23 24 22 37 38 40 39 41 Figure 14: Model 5600 Econominder Control Valve Drive Assembly 18
Résumé du contenu de la page N° 19
® Model 5600 & 5600 Econominder Model 5600 Econominder Control Valve Drive Assembly Item Number No. Req’d Part Number Description 11 housing, with roll pin 14448-000 1 14488-001 housing, with pin drilled for screw 1 14448-0 housing, with pin drilled for thumb screw 1A 1 15494-01 “L” housing, with pin 1 15494-03 “L” housing, with pin drilled for designer 2 1 13175 motor mounting plate 3 1 18743 motor, 120V, 60 Hz 1 13494 motor, 24V, 60 Hz 4 2-3 11384 screw, motor mtg. and ground wire 5 2-4 13296
Résumé du contenu de la page N° 20
® Model 5600 & 5600 Econominder Bypass Valve Assembly, Plastic 9 10 11 12A 12B Figure 15: Bypass Valve Assembly, Plastic Item Number No. Req’d Part Number Description 9 2 13305 o-ring, 119 10 2 13255 clip, mounting 11 2 13314 screw, hex washer head, #8-18 x 5/8" 12A 1 18706 yoke, plastic 1" NPT 1 18706-02 yoke, plastic 3/4" 12B 1 13708 yoke, 3/4" 1 13708NP yoke, 3/4" (nickel-plated) 1 13398 yoke, 1" 1 13398NP yoke, 1" (nickel-plated) 20
