Résumé du contenu de la page N° 1
EZ-64TW1/EZ-74TW2/EZ-84FM
EZ-95FM
DP SERIES II (Data Port)
2-Way Paging Remote Engine Starting & Keyless
Entry System with 1-Way Sidekick Remote Control
OPERATING INSTRUCTIONS
IMPORTANT INFORMATION: Primary and Optional Features
PRIMARY: These are features that must be connected in order for the system to operate properly i.e. Remote Start
connections, Flashing Lights, Brake Reset. For programming, the hood pin and program button are required.
OPTIONAL: These are feature
Résumé du contenu de la page N° 2
TABLE OF CONTENTS Operation Cautions & Warnings….………………..…………………………………….……………………….………2 2-Way Paging LED Remote TW1...........……………………………………………………….……………….……….3 2-Way Paging LCD Remote TW2..…….…………………………….………………………………….……………….4 2-Way Paging LCD Remote FM…..……....……………………………………………………………….………...…..5 Using the Remote 1-Way Remote………………………………………………….…….……………………..….….6-7 Remote Engine Starting……………………………………………………………..…………………………….…..8-11 Turbo Timer Mode……………………………….………………………………....………………………….
Résumé du contenu de la page N° 3
2-WAY PAGING LED REMOTE EZ-64TW1 OPERATION: FIXED BUTTON 1 (Lock Symbol): ANTENNA • Press and release to Lock doors. • Press and Hold for more than 3 seconds to activate PAGING “Panic” feature. LED's BUTTON 2 (Unlock Symbol): • Press and release to Unlock doors. #1 #2 LOCK UNLOCK BUTTON 3 (Trunk Symbol): • Press and Hold for two seconds to activate trunk pop #5 (Optional Feature). nd 2 CAR BUTTON 4 (Start): #4 • Press and Hold for
Résumé du contenu de la page N° 4
2-WAY PAGING LCD REMOTE EZ-74TW2 OPERATION: BUTTON 1 (LOCK Symbol): FIXED • Press and release to Lock doors. ANTENNA • Press and Hold for more than 3 seconds to activate “Panic” #2 UNLOCK feature. #1 LOCK BUTTON 2 (Unlock Symbol): • Press and release to Unlock doors. BUTTON 3 (Trunk Symbol): AM • Press and Hold two seconds to activate trunk pop (Optional Feature). #5 RECALL LCD BUTTON 4 (Start Key Symbol): CAR I or II SCREEN • Press and Hold two seconds to Start/Stop
Résumé du contenu de la page N° 5
2-WAY PAGING LCD REMOTE EZ-84FM/95FM OPERATION: BUTTON 1 (Lock Symbol): FIXED • Press and release to Lock system. ANTENNA Press and Hold for more than 3 seconds to activate “Panic” feature. BUTTON 2 (Unlock Symbol): LCD • Press and release to Unlock system. SCREEN PM BUTTON 3 (Trunk Symbol): #5 • Press and Release to activate trunk pop (Optional RECALL / Feature). CAR I OR II #2 DISARM/ BUTTON 4 (Start Symbol): UNLOCK • Press and release to Start/Stop Engine. #1 A
Résumé du contenu de la page N° 6
USING THE 1-WAY REMOTE OPERATION: #2 UNLOCK #1 BUTTON 1 (Lock Symbol): #2 LOCK FLASHLIGHT • Press and release to Lock doors. UNLOCK #5 #3 VEHICLE 2 • Press and Hold for more than 3 seconds to TRUNK #4 activate “PaR n Ei Mc OT ” E feature. #1 START BUTTON 2 (Unlock Symbol): LOCK FLASHLIGHT • Press and release to Unlock doors. BUTTON 3 (Trunk Symbol): VEHICLE 2 • Press and Hold for two seconds to activate #3 #5 trunk pop (Optional Feature). TRUNK EZ S
Résumé du contenu de la page N° 7
USING THE 1-WAY REMOTE EZ-95FM OPERATION: BUTTON 1 (Lock Symbol): • Press and release to Lock doors. #3 • Press and Hold for more than 3 seconds to activate TRUNK “Panic” feature. BUTTON 2 (Unlock Symbol): • Press and release to Unlock doors. • Press 2 times for Driver Door Priority Unlock. #1 #2 BUTTON 3 (Trunk Symbol): LOCK UNLOCK • Press and Hold for ½ second or press twice to (AUX#2) (AUX#3) activate trunk pop. START BUTTON 4 (Start): R • ep P la re cs es m a en nd
Résumé du contenu de la page N° 8
REMOTE ENGINE STARTING REMOTE ENGINE STARTING - SUCCESSFUL START: 1) Press the remote start button for at least 1/2 second (Default) or twice if set for double press. 2) Parking lights flash once; return solid, and the Ignition/Acc circuits turn on. 3) After a few seconds the Starter Motor engages, Parking lights and Acc circuits will turn off while cranking. 4) Engine Starts and Runs. Parking Lights and Acc turn back on, Doors Lock. 5) Engine will remain running for programmed run tim
Résumé du contenu de la page N° 9
REMOTE ENGINE STARTING Cont. ENTERING YOUR REMOTE STARTED VEHICLE: 1) With engine running, Remote Unlock system (If equipped) or open door with key. 2) Enter vehicle and be careful not to step on brake pedal! (Remote Start Reset). 3) Turn Ignition to ON/RUN position, then press brake pedal to reset the Remote Starter & Shift out of park. 4) Remote starter will reset instantly when the brake is pressed. Parking lights will turn off and the ignition key is now controlling your vehicle.
Résumé du contenu de la page N° 10
REMOTE ENGINE STARTING IDLE DOWN MODE - EXITING THE VEHICLE: 1) With vehicle engine running with key, **press the Remote Start button for at least a 1/2 second or twice if set for double press. 2) Parking Lights will turn ON. 3) Doors will unlock, or if brake pedal is being depressed, doors will unlock when it is released. 4) Turn OFF Ignition and remove key. Engine should remain running. 5) Exit vehicle, then remote lock doors if desired. 6) Engine will remain running for programmed
Résumé du contenu de la page N° 11
REMOTE ENGINE STARTING INFINITY RUN MODE – EXITING THE VEHICLE: 1) With vehicle engine running with the key, **press the Remote Start button for at least 1/2 second, pause a few seconds, then press and release the remote start button a second time. 2) Parking Lights will start flashing, and doors will unlock. 3) Turn Ignition switch OFF, remove key and exit the vehicle. Engine should remain running. 4) The vehicle’s parking lights will flash for the programmed run time of 12, 24, or 36,
Résumé du contenu de la page N° 12
TURBO TIMER MODE (OPTIONAL) The optional Turbo Timer mode allows the EZEE Start system to keep a Turbo or Turbo Diesel vehicle running for 1 to 5 minutes [selectively] after you remove the key, exit the vehicle, and lock the doors remotely. This is handy for turbo cool-down without the need for expensive turbo timers. This mode requires the use of an extra part called a momentary switch/button that is not included with the kit. Check with your installer about adding this feature. NOT
Résumé du contenu de la page N° 13
CONVENIENCE AND SAFETY FEATURES KEYLESS ENTRY (POWER DOOR LOCK CONTROL, Optional) This system enables you to remotely lock and unlock the vehicle’s doors (if equipped with power locks) via remote control for safety and convenience. Note: This feature may require extra labor and/or parts to install. Press the Lock or Unlock transmitter button as you leave or come near the vehicle. Parking lights will flash once for lock and twice for unlock. If vehicle is running by the remote start sy
Résumé du contenu de la page N° 14
CONVENIENCE AND SAFETY FEATURES VALET MODE / STARTER DISABLE OVERRIDE Before servicing your vehicle or handing the keys over to a Valet we recommend putting the unit into valet mode. The remote start function WILL NOT operate when in Valet mode. To enter Valet mode, turn the key to the ON position, press and hold Program/Valet switch for 5-6 seconds. The LED will turn on solid and the system is now in valet. Perform this procedure again to exit of Valet mode. The keyless entry will s
Résumé du contenu de la page N° 15
TRANSMITTER PROGRAMMING Note: All transmitter codes must be learned at time of programming!! The unit will learns up to 4 different transmitter codes. 1. Turn key to the ON position. 2. Press Programming button 4 times, then after a few seconds the unit flashes the parking lights 4 times. 3. Press button #1 & #2 together of the transmitter to be coded. You should get 2 light flashes indicating the unit is nd waiting for a 2 code, then press button #1 & #2 of a second transmitte
Résumé du contenu de la page N° 16
2-VEHICLE OPERATION A single remote can control two different vehicles EZEE Start systems installed. However, both systems must be the same type. EZ-64TW1/1704TW2 is not compatible with EZ- 84FM/95FM. Programming: nd VEHICLE #2 You must first Program your remote for 2 Press side button vehicle operation: nd (2 Vehicle Programming and Operation instruction): first, then you have 1 Way sidekick remote 4 seconds to In step #4 of transmitter programming (see page 15) press side EZ START
Résumé du contenu de la page N° 17
2-VEHICLE OPERATION Cont. L.E.D Two-way Remote In step #4 of transmitter programming (see Page 15), press and hold the side button on the LED remote for 5 seconds. The nd unit will beep 2 times and a yellow LED will flash (now you are in 2 vehicle operation mode). Press the lock and unlock nd button at the same time on the LED remote, your vehicle should be programmed for the 2 vehicle. Operation: nd Press the car vehicle #2 side button on your remote for 5 seconds to enter 2 vehicle
Résumé du contenu de la page N° 18
TROUBLESHOOTING cont. NO RESPONSE FROM REMOTE TRANSMITTERS: (4 Parts) 1. Check for proper power/ground wiring connections at module. 2. Check Antenna Module connection. The antenna module included with this system must be plugged in. 3. Transmitters may need to be programmed to the unit. See transmitter programming steps on Page 15. 4. Check transmitter Batteries and replace if necessary. UNIT CRANKS VEHICLE BUT ENGINE NEVER STARTS: (2 parts) 1. In extreme cold or severe weather con
Résumé du contenu de la page N° 19
REMOTE START DIAGNOSTICS If the system flashes the parking lights one to three times and doesn’t attempt remote, it means the following: 1 Parking Light Flash = Problem with Brake Switch. 2 Parking Light Flashes = Problem with Hood Switch. 3 Parking Light Flashes = Valet Service Mode. LOW BATTERY WARNING - LCD REMOTE (EZ-64TW1/EZ-74TW2) EZ-64TW1 (LED system): When the battery is low the orange and green LED flash 6 times with any button pressed. EZ-74TW2/EZ-84FM/95FM (LCD S
Résumé du contenu de la page N° 20
SETTING THE CLOCK (2-WAY- LCD REMOTE) EZ-74 TW2 1. Press the Recall button #5 on the side of the remote control 5 times. 2. The remote will beep and the AM or PM display will begin flashing. 3. Press the Lock button #1 to increase time. 4. Press the Unlock button #2 to decrease time. 5. Press the Trunk button #3 to go to the next item – AM - PM - Hour- Minutes. 6. Press the Start button #4 to Disable or Enable Beep. 7. Press the Recall button #5 to Exit Setup or wait 7 seconds, the
