Résumé du contenu de la page N° 1
MDG76PC
(Phase 7.3 Coin Gas DSI)
Installation Manual
AVERTISSEMENT: Assurez-vous de bien
WARNING: For your safety the information in
this manual must be followed to minimize the risk suivre les instructions données dans cette notice
pour réduire au minimum le risque d’incendie
of fire or explosion or to prevent property
damage, personal injury or death. ou d’explosion ou pour éviter tout dommage
matériel, toute blessure ou la mort.
— Do not store or use gasoline or other flammable — Ne pas ent
Résumé du contenu de la page N° 2
Retain This Manual In A Safe Place For Future Reference Our products embody advanced concepts in engineering, design, and safety. If this product is properly maintained, it will provide many years of safe, efficient, and trouble free operation. ONLY qualified technicians should service this equipment. OBSERVE ALL SAFETY PRECAUTIONS displayed on the equipment or specified in the installation manual included with the dryer. The following “FOR YOUR SAFETY” caution must be posted near the dryer in
Résumé du contenu de la page N° 3
IMPORTANT YOU MUST DISCONNECT AND LOCKOUT THE ELECTRIC SUPPLY AND THE GAS SUPPLY BEFORE ANY COVERS OR GUARDS ARE REMOVED FROM THE MACHINE TO ALLOW ACCESS FOR CLEANING, ADJUSTING, INSTALLATION, OR TESTING OF ANY EQUIPMENT PER OSHA (Occupational Safety and Health Administration) STANDARDS. «Attention: Au moment de l’entretien des commandes, étiquetez tous les fils avant de “Caution: Label all wires prior to les débrancher. Des erreurs de câblage disconnection when servicing controls. Wiring peuv
Résumé du contenu de la page N° 4
WARNING The dryer must never be operated with any of the back guards, outer tops, or service panels removed. PERSONAL INJURY OR FIRE COULD RESULT. WARNING DRYER MUST NEVER BE OPERATED WITHOUT THE LINT FILTER/SCREEN IN PLACE, EVEN IF AN EXTERNAL LINT COLLECTION SYSTEM IS USED. IMPORTANT PLEASE OBSERVE ALL SAFETY PRECAUTIONS displayed on the equipment and/or specified in the installation manual included with the dryer. Dryer must not be installed or stored in an area where it will be exposed to w
Résumé du contenu de la page N° 5
Table of Contents SECTION I IMPORTANT INFORMATION ............................................................................... 3 A. Receiving and Handling ............................................................................................................... 3 B. Safety Precautions ...................................................................................................................... 4 SECTION II SPECIFICATIONS/COMPONENT IDENTIFICATION...................................
Résumé du contenu de la page N° 6
SECTION V DATA LABEL INFORMATION .............................................................................33 A. Data Label ............................................................................................................................... 33 SECTION VI PROCEDURE FOR FUNCTIONAL CHECK OF REPLACEMENT COMPONENTS........................................................................................................ 35
Résumé du contenu de la page N° 7
SECTION I IMPORTANT INFORMATION A. RECEIVING AND HANDLING The dryer is shipped in a protective stretch wrap cover with protective cardboard corners and top cover (or optional box) as a means of preventing damage in transit. Upon delivery, the dryer and/or packaging, and wooden skid should be visually inspected for shipping damage. If any damage whatsoever is noticed, inspect further before delivering carrier leaves. Dryers damaged in shipment: 1. ALL dryers should be inspected upon receipt an
Résumé du contenu de la page N° 8
B. SAFETY PRECAUTIONS WARNING: For your safety, the information in this manual must be followed to minimize the risk of fire or explosion or to prevent property damage, personal injury, or loss of life. WARNING: The dryer must never be operated with any of the back guards, outer tops, or service panels removed. PERSONAL INJURY OR FIRE COULD RESULT. 1. DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. 2. Purchaser/user should cons
Résumé du contenu de la page N° 9
7. A program should be established for the inspection and cleaning of lint in the burner area, exhaust ductwork, and area around the back of the dryer. The frequency of inspection and cleaning can best be determined from experience at each location. WARNING: The collection of lint in the burner area and exhaust ductwork can create a potential fire hazard. 8. For personal safety, the dryer must be electrically grounded in accordance with local codes and/or the National Electrical Code ANSI/NFPA
Résumé du contenu de la page N° 10
SECTION II SPECIFICATIONS/COMPONENT IDENTIFICATION A. SPECIFICATIONS 113.03 cm BASKET (TUMBLER) DIAMETER 44-1/2” 63.18 cm BASKET (TUMBLER) DEPTH 24-7/8” 0.746 kW BASKET (TUMBLER) MOTOR 1 hp DOOR OPENING (DIAMETER) 31-3/8” 79.7 cm BASKET (TUMBLER) VOLUME 22.4 cu.ft. 0.634 cu.m. VOLTAGE AVAILABLE 120v 1ø, 60 Hz 51,408 kcal/hr HEAT INPUT 204,000 Btu/hr AIRFLOW 1,200 cfm 33.98 cmm INLET PIPE CONNECTION 3/4” F.N.P.T.* 052103 Shaded areas are stated in metric equivalents * A minimu
Résumé du contenu de la page N° 11
Specifications MDG76PC NOTE: Manufacturer reserves the right to make changes in specifications at any time without notice or obligation. 7
Résumé du contenu de la page N° 12
B. COMPONENT IDENTIFICATION 1. Dryer Front View Illus. No. Description 1 Controls 2 Control (top access) Door Assembly 3 Main Door Assembly 4 Lint Compartment Area (lint screen located behind door) 5 Data Label and Installation Label (affixed to the left side panel area behind the top control [access] door) 8
Résumé du contenu de la page N° 13
2. Dryer Rear View Illus. No. Description 1 Heating Unit 2* Electric Service Relay Box 3 Basket (tumbler) Bearing Mount Assembly 4 Idler Bearing Mount Assembly 5 Basket (tumbler) (drive) Motor Assembly (for reversing models ONLY) 6 Blower Motor Assembly 7 Dryer Exhaust * Electric service connections for gas models are made in this box. 9
Résumé du contenu de la page N° 14
SECTION III INSTALLATION PROCEDURES Installation should be performed by competent technicians in accordance with local and state codes. In the absence of these codes, the installation must conform to applicable American National Standards: ANSI Z223.1- LATEST EDITION (National Fuel Gas Code) or ANSI/NFPA NO. 70-LATEST EDITION (National Electrical Code) or in Canada, the installation must conform to applicable Canadian Standards: CAN/CGA-B149.1-M91 (Natural Gas) or CAN/CGA-B149.2-M91 (Liquid Pro
Résumé du contenu de la page N° 15
10. The dryer must be installed with provisions for adequate combustion and make-up air supply. CAUTION: This dryer produces combustible lint and must be exhausted to the outdoors. Every 6 months, inspect the exhaust ducting and remove any lint build up. IMPORTANT: Dryer must be installed in a location/environment, which the ambient temperature remains between 40° F (4.44° C) and 130° F (54.44° C). B. UNPACKING/SETTING UP Remove protective shipping material (i.e., plastic wrap, and/or optional
Résumé du contenu de la page N° 16
c. Remove the four (4) self-taping screws on the burner box that secure it to the top of the dryer shown in the illustration below. d. Remove the two (2) self-taping screws on the back electrical box and pull through ALL associated wires from the motor to this electrical box (refer to the illustration below). e. Reverse procedure for installing top section. 12
Résumé du contenu de la page N° 17
C. DRYER ENCLOSURE REQUIREMENTS Bulkheads and partitions should be made of noncombustible materials and must be located a minimum of 12-inches (30.48 cm) (18-inches [45.72 cm] or more is recommended for ease of installation, maintenance, and service) above the dryer outer top, except along the front of the dryer which may be partially closed in if desired. The clearance between the bulkhead header and the dryer must be a minimum of 4-inches (10.16 cm) and must not extend more than 4-inches (10.
Résumé du contenu de la page N° 18
D. FRESH AIR SUPPLY REQUIREMENTS When the dryer is operating, it draws in room air, heats it, passes this air through the basket (tumbler), and exhausts it out of the building. Therefore, the room air must be continually replenished from the outdoors. If the make-up air is inadequate, drying time and drying efficiency will be adversely affected. Ignition problems and sail switch “fluttering” problems may result, as well as premature motor failure from overheating. Air supply (make-up air) mu
Résumé du contenu de la page N° 19
E. EXHAUST REQUIREMENTS 1. General Exhaust Ductwork Information Exhaust ductwork should be designed and installed by a qualified professional. Improperly sized ductwork will create excessive back pressure which results in slow drying, increased use of energy, overheating of the dryer, and shutdown of the burner by the airflow (sail) switches, burner hi-limits, or basket (tumbler) hi-limit thermostats. The dryer must be installed with a proper exhaust duct connection to the outside. CAUTION: T
Résumé du contenu de la page N° 20
NOTE: As per the National Fuel Gas Code, “Exhaust ducts for type 2 clothes dryers shall be constructed of sheet metal or other noncombustible material. Such ducts shall be equivalent in strength and corrosion resistance to ducts made of galvanized sheet steel not less than 0.0195-inches (26 gauge [0.05 mm]) thick.” IMPORTANT: Exhaust back pressure measured by a manometer in the exhaust duct must be no less than 0 and must not exceed 0.3 inches (0.74 mb) of water column (W.C.). IMPORTANT: Minimu
