Instruction d'utilisation Craftsman 486.246231

Résumé du contenu de la page N° 1

Owner's Manual
TRACTOR BRUSH GUARD
Model No's. 486.246212, 486.246221 & 486.246231
_ii.......... i_ '_ _'_:( •..... •.............
CAUTION:
• Safety
Before using this product, read
• AssembLy
this manuaU and follow aH Safety
,, Operation
RuUes and
Operating Instructions. • Maintenance
• Parts
IMPORTANT - READ THtS FIRST!!!
For Missing Parts or AssembUy Questions
PUease Call 866-576-8388
Mon.-Fri. 7 am - 5 pm CST.
FAX 217-728-2032 or e-mail info@aq_ri-fab.com
Missing parts will be sent UPS in 24

Résumé du contenu de la page N° 2

ONE YEAR UMITED WARRANTY When operated and maintained according to the instructions supplied with it, if this Tractor Brush Guard fails due to a defect in material or workmanship within one year from the date of purchase, cal! 1-800-4-MY-HOME ®to arrange for free repair. If this product is used for commercial or rental purposes, this warranty applies for only 90 days from the date of purchase. This warranty gives you specific legal rights, and you may also have other rights which vary from state

Résumé du contenu de la page N° 3

CARTON CONTENTS CAUTION! Muffler is hot! Allow engine to cool down before proceeding with bumper installation, NOTE: Right hand (RH) and left hand (LH) are determined from the operator's position while seated on the tractor, STEP 1: (SEE FIGURE 2) , Place cardboard on work surface. identify and lay out all parts and hardware. Not all hardware wil! be used. Unused hardware may be Part No. Ref, Description discarded after assembly. Remove hood from tractor using instructions in your #25038 1 Right

Résumé du contenu de la page N° 4

STEP 3: (SEE FIGURE 4) STEP 5: (SEE FIGURE 6) , Attach left mounting bracket to hole shown in left side , Replace the front screws and browning shield you of tractor frame using a hex bolt (C), fiat washer (I) removed in Step 1 as shown. and nylock nut (G). Align middle hote in bracket with empty hole in tractor frame. Tighten nylock nut (G) only enough to keep bracket in alignment until step 4. Repeat for right mounting bracket. (GT) FRAME SHOWN HEX LEFT MOUNTING BUMPER STOPS BOLT (C) BRACKET F

Résumé du contenu de la page N° 5

ASSEMBLING TO DUAL ROD DECK STEP 3: (SEE FIGURE 2) IMPORTANT: Do not remove any bolts from the tractor SUSPENSION TRACTORS frame while the mower deck is raised, Misatignment of holes in frame could result, IMPORTANT: These instructions are for tractors with dual mower deck suspension brackets like the examples Lower mower deck to rest on ground, shown in figure 2 on this page.. Remove bolts from mounting holes on both sides of tractor frame, Use a mounting bracket to help identify holes, CAUTION

Résumé du contenu de la page N° 6

STEP 4: (SEE F_GURE3} STEP 6: (SEE FIGURES 5 AND 6} , Attach left mounting bracket to hole shown in left side , Assemble plastic grips (F) onto locking levers. of tractor frame using bolt (C), !ock washer (H) and , To attach bumper to tractor: flat washer (I). Align middle hole in bracket with empty 1. Place flattened ends of bumper onto mounting hole in tractor frame and tighten bolt (C) to hold brackets. Insert pin of locking lever through front bracket in place. Repeat for right mounting brac

Résumé du contenu de la page N° 7

Résumé du contenu de la page N° 8

Your Home 1111111111111117 `¸ iiiiiiiiiiiiiiiiiiiiiiiiT_ iiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiii For repair-in your home-of all major brand appliances, iiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiii lawn and garden equipment, or heating and cooling systems, iiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiii no matter who made it, no matter who sold it! iiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiii For the replacement parts, accessories and iiiiiiiiiiii