Résumé du contenu de la page N° 1
HEARTH PRODUCTS
KITS AND ACCESSORIES
P/n 775258M
PILLAR FACE KITS
Rev. A, 10/2010
MODELS RAvEnnA™, DESIgnER™ AnD RA vELLE™ 30
InSTALLATIOn InSTRUCTIOnS FOR InSTALLIng PILLAR
FACE KITS FOR USE w ITh MODELS RAvEnn A™,
DESIgn ER™ AnD RAvELLE™ 30 gAS APPLIAnCES
KIT COnTEnTS
Please ensure that all these parts are in one of the three boxes. The pillar
Cast Surround *
face comes packaged in three separate boxes. The following items are
included in each box:
Pillared Face
Box 1 - Part # 75093
Cas
Résumé du contenu de la page N° 2
R30 TURn OFF ThE FIREPLACE AnD ALLOw IT TO COMPLETELY COOL Step 3. Ravelle 30 Fireplace - Backing Plate Installation Instructions: BEFORE PROCEEDIng. a) There is a 1” lip (see A in Figure 3) at the lower front of the fire- Note: Skip the steps that do not specify your model appliance. place. The lower brackets on the backing plate have a hook (see B in Figure 3) on their bottom edge. The face should be placed so InSTALLATIOn In STRUCTIOnS the hook on the lower bracket catches the 1” lip on t
Résumé du contenu de la page N° 3
D Turn Deflector so Bent Edge Faces the Front E C F g h I C = Upper Brackets D = Captive Screws E = Captive nuts Front view of Designer™ and Ravenna Inserts F = Air Deflector h = Side bracket upper mounting surface g = hex head Screws I = Side bracket lower mounting surface Figure 5 Figure 4 Step 4. Designer™ and Ravenna™ gas Inserts - Pillar Face Assembly Instructions: Rear view of a) Remove the backing plate and the two mounting brackets from Backing Plate the box. b)
Résumé du contenu de la page N° 4
Step 9. All Models - grill Installation Instructions: Two distinct looks can be obtained by installing either the ornate J grills or the traditional grills on your pillar face (see Figure 1B on Page 1). The bottom of the grill (see Figure 9) has a return on it. To install the upper grill (see M in Figure 9), rotate the K grill with the bottom down and place the grill on top of the door. Push the grill back until it rests against the recess in the pillars. J = hole in Top of Pillar To in
Résumé du contenu de la page N° 5
Step 10. All Models - Top Installation Instructions: The underside of the top has a semicircular recess at both ends. The pillars have a corresponding semicircular protrusion. Rotate the top as shown in Figure 10 and position the top so the recess Assembled Pillar Face in each end slides over the protrusions on the pillars (see P in Figure 10). P = Protrusions on Pillars P Figure 11 Step 13. All Models - Extended Knob Installation Instructions: When installing a cast pillar face on
Résumé du contenu de la page N° 6
REFEREnCE InFORMATIOn Designer™ and Ravenna™ Fireplace Inserts - Figure 16 shows the dimensions of the cast surround kit. See ordering information on Page 1. 45-1/2” (1156mm) 7-1/8” (181mm) 44-1/2” (1130mm) Figure 13 30” (762mm) 22-7/8” (581mm) 45-1/2” (1156mm) Figure 16 - Cast Surround Dimensions Figure 14 Figure 15 NOTE: DIAGRAMS AND ILLUSTRATIONS ARE NOT TO SCALE. Lennox Hearth Products reserves the right to make changes at any time, without notice, in design, materials, specifications, p
