Résumé du contenu de la page N° 1
INSTALLATION AND OPERATION MANUAL
TM
Catalytic Vent-Free
Wall-Mounted Gas Fireplace
Models: X-FIRES-1000-NG and X-FIRES-1000-LP
P/N 506023-01 Rev. C, 05/2009
Installer: Leave This Manual With The Appliance.
Consumer: Retain This Manual For Future Reference.
In the Commonwealth of Massachusetts:
Portland
• Installation must be performed by a licensed plumber or gas fitter
US
• See Table of Contents for location of additional Commonwealth of
X-Fires™ 1000
Report No. 317-F-10-5
Résumé du contenu de la page N° 2
• Children and adults should be alerted to the hazard of high 1.0 IMPORTANT SAFETY AND WARNING surface temperature and should stay away to avoid burns or clothing ignition. INFORMATION • Young children should be carefully supervised when they are in the same room with the heater. • Do not place clothing or other flammable material on or near WARNINGS the heater. • Any safety screen or guard removed for servicing the heater If the information in this manual is not fol- must be repl
Résumé du contenu de la page N° 3
These heaters are fitted with a specially designed pilot utilizing an CONGRATULATIONS! oxygen depletion sensor (ODS) which responds to the amount of oxygen available in the room and shuts the heater off before the When you purchased your new gas fireplace, you joined the oxygen level drops below 18%. It must not be adjusted or put out ranks of thousands of individuals whose answer to their home of operation. If replaced then manufacturers original parts must be heating needs reflects thei
Résumé du contenu de la page N° 4
Massachusetts Requirements 5.0 UNPACKING THE APPLIANCE These fireplaces are approved for installation in the US state of Mas- sachusetts if the following additional requirements are met: Remove the straps and the top lid of the outer packaging, remove any instructions or fixing kits. Read ALL these instructions before continuing • Unvented Room Heaters shall be installed in accordance with 527 to unpack or install this appliance. CMR and 248 CMR: Lift off the remaining packaging components.
Résumé du contenu de la page N° 5
Example: 8.0 COMBUSTION AND VENTILATION AIR Vent-free heater #1 9,000 BTU/Hr Vent-free heater #2 23,000 BTU/Hr This heater shall not be installed in a confined space or unusually tight Gas appliance #1 35,000 BTU/Hr construction unless provisions are provided for adequate combustion and (water heater) ventilation air. The heater may be located in unusually tight construction Total = 67,000 BTU/Hr provided the space is unconfined, or
Résumé du contenu de la page N° 6
Clearance to the sides of the appliance are 4” but curtains, drapes and 9.0 SITE REQUIREMENTS other fabrics are not permitted within a distance of 20” of the appliance sides. No such materials are permitted directly above the appliance regardless of distance. This appliance is designed to be wall-hung. Do not recess any part of the appliance into the wall. The minimum clearance to the ceiling above the appliance is 32” mea- sured from the top of the appliance glass panel. This appliance may
Résumé du contenu de la page N° 7
Non-concealed gas connections may be made using the entry points at either end of the firebox or the one in 1. Remove the Grill. the bottom of the firebox. A concealed gas connection Note : X-Fire 1000 Note: This design of grill shown as example may be made using the knock out hole in the center not fitted to widescreen model back of the firebox. Select the most appropriate entry point and knock out the relevant hole in both the firebox and the outer casing. 5. Widescreen models : Remove tw
Résumé du contenu de la page N° 8
A full size fitting template is supplied to assist with wall mounting. (see 1.0 MOUNTING THE APPLIANCE Figure 3). After having selected the final mounting position of the appliance, taking If the heater is to be installed on a studded wall with conventional 16” into account the site requirements as specified in these instructions, stud spacing then a wall mounting plate is supplied to enable this. NOTE: the integrity of the wall, and the feasibility of the proposed supply pipe THIS APPLI
Résumé du contenu de la page N° 9
It is recommended that the burner height, where possible, should 13.0 FITTING THE SURROUND ASSEMBLY be approximately 4 ft. from the floor. This will give the best viewing position. When selecting the height, ensure that the clearance to the ceiling is 3" minimum, as specified on Page 6. Due to the weight of the frame assembly, it is recommended to seek assistance for this operation. After selecting the final mounting position of the appliance, taking into account the site requirements as
Résumé du contenu de la page N° 10
An ANSI approved manual shut-off valve and union must be installed 14.0 CHECKING THE BURNER upstream of the heater within the fireplace cavity when rigid pipe is used. Ensure that a sediment trap is installed upstream of the heater (Figure 4) within the structure’s piping system to prevent moisture There are no imitation fuel bed components, such as logs or rocks, and contaminants from passing through the pipe to the heater controls to install. The appliance features a ribbon burner which
Résumé du contenu de la page N° 11
If the pressure is too high, the gas supply meter may be set incorrectly. 18.0 SPARK GAP This should be checked with the appliance running and if necessary reset by the gas supplier. If the burner pressure is too low, then check the inlet pressure with the appliance running. If this is less than the inlet The gap between the spark electrode and the pilot should be 1/8” to pressure stated in Table 1, it will need to be reset by the gas supplier. 3/16” to produce a good spark. There shoul
Résumé du contenu de la page N° 12
7. Remove the burner unit, strip off the burner pipes and clean thor- 0.0 SERVICING oughly. 8. C lean the in-line restrictor, pilot assembly and the burner tube. Clean the exterior of the pilot assembly with a soft brush and blow through the flame ports on the pilot head. Check the aeration holes are free WARNING from lint or dirt. Do not attempt to remove the pilot injector as this Turn off the appliance and allow to cool before can cause damage. The pilot assembly is a non-servi
Résumé du contenu de la page N° 13
Turn on the fireplace as per the operating instructions, and run at 1.0 CA TALYSTS maximum setting for 15 minutes. Position gas sample probe directly over a catalyst via the outlet grill, on top of the appliance. Record the carbon dioxide (CO ) concentration and then the carbon monoxide (CO) WARNING concentration as displayed by the analyzer - also noting the units in which the values are expressed. Most analyzers display carbon dioxide Do not block the catalysts or the applianc
Résumé du contenu de la page N° 14
3.0 LIGHTING INSTRUCTIONS & TURNING OFF APPLIANCE FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. • Immediately call your gas supplier from a neighbor’s phone. A. T his appliance has a pilot which must be lit with a piezo spark Follow the gas supplier’s instructions. igniter. When lighting the pilot, follow these instructions exactly.
Résumé du contenu de la page N° 15
4.0 TROUBLESHOOTING GUIDE PROBLEM CORRECTIVE ACTION Igniter sparks but pilot does not light • No gas to Pilot, check the gas line connections. • Air not fully purged. Purge supply or wait longer. • Spark grounding to metal work, reset gap correctly. • Blocked pilot, clean out internally. Pilot lights but then goes out • Severe restriction in gas supply: clear obstruction. • Faulty thermocouple, replace pilot assembly. • Blocked pilot, clean out. • Blocked lint gauze, clean. • Hold c
Résumé du contenu de la page N° 16
5.0 REPLACEMENT PARTS - X-FIRES-1000 POSITION SPIRIT LEVEL ALONG THIS EDGE TO LEVEL TEMPLATE BEFORE MARKING OUT WALL COLOQUE EL NIVEL SOBRE ESTE BORDE PARA NIVELAR LA PLANTILLA ANTES DE MARCAR LA PARED FIXING POINTS PIERCE TEMPLATE TO MARK HOLE POSITION ON WALL X 4 PUNTOS DE SUJECION PERFORE LA PLANTILLA PARA MARCAR LA POSICION DE LOS 4 TALADROS EN LA PARED 16” (406mm) Replacement Parts WALL MOUNTED VENT FREE FITTING TEMPLATE PLANTILLA PARA LA INSTALACION DE CHIMENEAS DE PARED SIN SALIDA DE HU
Résumé du contenu de la page N° 17
6.0 POSITIONING OF FIELD REMOVABLE PARTS WARNING Failure to position the parts in accordance with these diagrams Glass Door Removal: or failure to use only parts specifi- Remove the four (4) cally approved with this heater screws indicated, then lift door off. may result in property damage or personal injury. Visual check for cor- rect pilot flame. 4 off burner Figure 13 installation positions As our policy is one of continuous improvement and development, we hope therefore you
Résumé du contenu de la page N° 18
7.0 SPECIFICATIONS Product Reference Information Cat. No. Model Ship. Wt. Ship. Volume H7 X-FIRE-1000-NG 46 lb. 3.31 cu. ft. H7 3 X-FIRE-1000-LP 46 lb. 3.31 cu. ft. Surround Specifications 39-7/16” 39-7/16” 21-3/16” 21-3/16” 11-1/4” 21-7/16” 11-1/4” 25-1/4” 21-7/16” 25-1/4” 7-1/2” 4-1/2” 7-1/2” 4-1/2” 15-3/4” 15-3/4” 23-3/4” 23-3/4” Note: Limestone and Granite are natural products and therefore each piece will have its own unique character with no two pieces being quite the same. X-FIRE-1
Résumé du contenu de la page N° 19
GAS ENTRY POINT DIMENSIONS TOP VIEW Finished Wall Fireplace Regulator Gas Entry Point REGULATOR GAS ENTRY POINT Model D1 D D3 9/16” 1-9/16” 4-1/8” X-fires™ 1000 (15mm) (40mm) (105mm) Note: The actual dimensions are shown in millimeters. The fractional dimensions are converted from millimeters and are rounded to the nearest 1/16”. KEY: D1 = Distance from mounting surface to rear entry point D2 D = Distance from mounting surface to center of side entry point D3 = Distance from mounting surfac
Résumé du contenu de la page N° 20
8.0 PRODUCT REFERENCE INFORMA TION WARRANTY Normally, all parts should be ordered through your Lennox distributor or dealer. Parts will be shipped at prevailing prices at time of order. Your gas appliance is covered by a limited warranty. Please read the warranty to be familiar with its coverage. When ordering repair parts, always give the following information: Retain this manual. File it with your other documents for future refer- 1. The model number of the appliance. ence. . The serial
