Résumé du contenu de la page N° 1
™ ™
E-Studio & E-box
Balanced Flue
With upgradable control valve
Instructions for Use,
Installation and Servicing
For use in GB, IE (Great Britain and Eire)
This appliance has been certified for use in countries other than those stated. To install this appliance in these countries, it is essential to obtain the
translated instructions and in some cases the appliance will require modification. Contact Gazco for further information.
IMPORTANT
Do not attempt to burn rubbish on this fire. This app
Résumé du contenu de la page N° 2
CONTENTS Covering the following models: 8692BFCHUC 8692MCUC 8692PBUC P8692BFCHUC P8692MCUC 8692PBUC APPlIANCE COMMISSIONING ChECKlIST 3 USER INSTRUCTIONS 4 INSTAllATION INSTRUCTIONS 11 Technical Specifications 11 Site Requirements 14 Installation 16 Commissioning 23 SERvICING INSTRUCTIONS 24 Servicing Requirements 24 Fault Finding 24 How to replace parts 26 Basic spare parts list 31 Service Record 32 2
Résumé du contenu de la page N° 3
APPlIANCE COMMISSIONING ChECKlIST IMPORTANT NOTICE Explain the operation of the appliance to the end user, hand the completed instructions to them for safe keeping, as the information will be required when making any guaranteed claims. FlUE ChECK PASS FAIl 1. Flue is correct for appliance 2. Flue flow test N/A 3. Spillage test N/A GAS ChECK 1. Gas soundness & let by test 2. Standing pressure test mb 3. Appliance working pressure (on High Setting) mb NB All other gas appliances must be op
Résumé du contenu de la page N° 4
USER INSTRUCTIONS knob is pointing to pilot . The pilot should now light. If the pilot has not lit, repeat the procedure until it 1. GENERAl does. • Keep the control knob pressed for 10 seconds and then 1.1 Installation and servicing must only be carried out by a release it, the pilot should stay alight. If the pilot goes out, competent person. repeat the procedures until it does. 1.2 In all correspondence, please quote the appliance type and 2.3 I
Résumé du contenu de la page N° 5
USER INSTRUCTIONS TIMER MODE it will turn the fire on and off according to 3 pre-set programme and automatically regulate the room temperature during the two periods. GAZCO PART NO. 8456. ClEANING ThE FIRE ENSURE ThE FIRE IS COlD BEFORE PROCEEDING 5.1 • Refer to the separate Frame Instructions to remove the frame from the fire. AR1465 AR1423 5A. ClEANING ThE E-STUDIO 5.5 To clean the glass surface, Gazco recommends you use a ceramic glass product generally sold for cleaning cera
Résumé du contenu de la page N° 6
USER INSTRUCTIONS 5 6 6A. ARRANGEMENT OF ThE A FUEl BED COMPONENTS - E STUDIO ONlY USE ThE CORRECT TYPE AND QUANTITY OF GRANITE ChIPPINGS. AlwAYS FOllO w ThE FUEl BED lAYOUT AS STATED IN ThESE INSTRUCTIONS. NEvER ChANGE ThE lAYOUT FROM ThAT ShOwN hERE. AR1997 6.1 • Arrange the granite chippings in the areas highlighted in Diagram 4. Granite chippings should be evenly distributed. 4 • Ensure that no chippings overhang or fill the pilot area, Arrow B, Diagram 7. NOTE:
Résumé du contenu de la page N° 7
USER INSTRUCTIONS • Refer to the separate Frame Instructions to replace the 11 frame on the fire 6B. ARRANGEMENT OF ThE FUEl BED COMPONENTS - E-BOX NOTE: CERAMIC PARTS ARE FRAGIlE. hANDlE wITh CARE ONlY USE ThE CORRECT TYPE AND QUANTITY OF CERAMIC COMPONENTS AR1362 6.3 • Place the rear panel against the rear of the box resting on the shelf • Slide one of the side panels into the box ensuring it touches the rear panel • Place the front coal centrally i
Résumé du contenu de la page N° 8
USER INSTRUCTIONS • Place the last two small coals to the left and right-hand 14 side of the bed in the two spaces, Diagram 18. 18 AR1364 • Place 2 medium-size coals either side of the first large AR1368 coal, in the recess between the flame baffle and the front coal, Diagram 15. 15 PEBBlE lAYOUT • Position the pebble flame baffle centrally on the tray and ensure the stepped lower edge engages against the rear edge of the burner skin, Diagram 19. 19 AR13
Résumé du contenu de la page N° 9
USER INSTRUCTIONS 21 FITTING ThE GlASS wINDOw - E-BOX 6.9 • Ensure that the fibre glass window seal on the box is intact, then lower the glass window into the lower retaining bracket. • Hold the window and position the upper retaining bracket • Secure using the 4 screws. AR1408 A4 A5 A3 A6 • Tighten the bottom and top screws to retain the window, Diagram 24. • Place the next four pebbles as shown resting between the 24 flame baffle and
Résumé du contenu de la page N° 10
USER INSTRUCTIONS 10. vENTIlATION 10.1 This appliance requires no additional ventilation. 11. INSTAll ATION DETAIlS 11.1 To assist in any future correspondence, your installer should have completed the commissioning sheet at the front of this book, this records the essential installation details of the appliance. In all correspondence always quote the Model number and Serial number. 12. hOT SURFACES 12.1 Parts of this appliance become hot during normal use. It is therefore recommended that
Résumé du contenu de la page N° 11
INSTAllATION INSTRUCTIONS TEChNICAl SPECIFICATION Covering the following E-STUDIO models: 8692BFChUC P8692BFChUC I I 2H 3P GAS CATEGORY Natural Propane G20 G31 Gas Type 20mbar 37mbar Working Pressure 4.3kW 3.75kW hIGh Gross Input kw lOw 2.5kW 2.3kW 3 0.401 0.138 Gas Rate m /hr 2 2 Efficiency Class 4 4 NO Class x 158 170R Injector Size 8mm x 15mm 23mm x 15mm Aeration Size 23mm x 15mm Flue Outlet Size 100mmø / 152mmø 8mm Gas Inlet APPlICABlE FRONTS FRONT PART NUMBER
Résumé du contenu de la page N° 12
INSTAllATION INSTRUCTIONS TEChNICAl SPECIFICATION Covering the following E-BOX models: 8692 MCUC 8692PBUC P8692 MCUC P8692PBUC I I 2H 3P GAS CATEGORY Natural Propane G20 G31 Gas Type 20mbar 37mbar Working Pressure 4.1kW 4.1kW hIGh Gross Input kw lOw 2.3kW 2.5kW 3 0.390 0.154 Gas Rate m /hr 1 1 Efficiency Class 3 3 NO Class x 260 104 Injector Size 12mm x 15mm 6mm x 15mm Aeration Size 23mm x 15mm Flue Outlet Size 100mmø / 152mmø 8mm Gas Inlet APPlICABlE FRONTS F
Résumé du contenu de la page N° 13
INSTAllATION INSTRUCTIONS TEChNICAl SPECIFICATION OvERAll EXTERNAl DIMENSIONS FOR BOTh E-STRUDIO AND E-BOX AR1427 MININUM AND MAXIMUM FlUE SIZE MINIMUM FLUE LENGTH MAXIMUM FLUE LENGTH AR1429 AR1428 13
Résumé du contenu de la page N° 14
INSTAllATION INSTRUCTIONS SITE REQUIREMENTS 1.4 The horizontal terminal can be reduced in length, Diagram 2. 1. FlUE AND ChIMNEY REQUIREMENTS 2 NOTE: This appliance can only be installed in conjunction with the flue supplied. 1.1 The flue must be sited in accordance with BS5440: Part 1 (latest edition), Diagram 1. 1.2 Any terminal which is less than 2 metres above any access (level ground, balcony or above a flat roof to which people have access) is to be fitted with a guard. AR0630 1.3
Résumé du contenu de la page N° 15
INSTAllATION INSTRUCTIONS SITE REQUIREMENTS TIMBER FRAMED BUIlDINGS 4 A 1.5 It will be necessary to provide additional clearance when B the flue passes through a wall containing any combustible D DIMENSIONS MIN MAX materials so as to prevent a fire hazard. A 420 mm 450 mm 1.6 The hole through which the flue will pass, must have a steel C B 560 mm 575 mm sleeve which is positioned so that an air gap of at least C 237 mm - 25mm is maintained between the outer surface of the flue, D 300 mm
Résumé du contenu de la page N° 16
INSTAllATION INSTRUCTIONS INSTAllATION 1. UNPACKING 4. INSTAllATION OF ThE GAS SUPPlY 1.1 • Remove the appliance from its packaging, and check that E-STUDIO BF it is complete and undamaged NAT GAS @ 20MB PROPANE @ 37mb • Put the loose ceramic parts to one side so that they are not damaged during installation. 8692BFCHUC P8692BFCHUC 2. CONTROl UPGRADE E-BOX BF NAT GAS @ 20MB PROPANE @ 37mb 2.1 Your fire is fitted with a control valve that can be easily upgraded t
Résumé du contenu de la page N° 17
INSTAllATION INSTRUCTIONS INSTAllATION 1 3 A AR1436 B AR1435 6.2 A 152mm (6’) diameter hole is required to install the flue. 5.2 Gas pipe entry must come through the rear right-hand side This can be achieved by either: of the box. The rubber seal must be cut using a sharp knife a) Core drill to allow the isolating elbow to pass through it. b) Hammer and chisel. It is advisable to drill small holes around the circumference •
Résumé du contenu de la page N° 18
INSTAllATION INSTRUCTIONS INSTAllATION 6.6 The void into which the appliance is fitted must be 8. INSTAllATION OF ThE APPlIANCE ventilated to prevent a build up of heat. If the void is sealed then it will be necessary to fit vents at both low and high 2 levels of approximately 50cm . These vents should take cold 8.1 The flue can be cut to length, measure the thickness of the air from the room and return warm air back into the room. wall the flue is passing through, then deduct 12mm. This
Résumé du contenu de la page N° 19
INSTAllATION INSTRUCTIONS INSTAllATION 10 5 9A. ARRANGEMENT OF ThE FUEl BED COMPONENTS - E STUDIO A ONlY USE ThE CORRECT TYPE AND QUANTITY OF GRANITE ChIPPINGS. AlwAYS FOllO w ThE FUEl BED lAYOUT AS STATED IN ThESE INSTRUCTIONS. NEvER ChANGE ThE lAYOUT FROM ThAT ShOwN hERE. 9.1 • Arrange the granite chippings in the areas highlighted in Diagram 8. Granite chippings should be evenly distributed. AR1997 8 • Ensure that no chippings over-hang or fill the pilot area, Arr
Résumé du contenu de la page N° 20
INSTAllATION INSTRUCTIONS INSTAllATION 15 9B. ARRANGEMENT OF ThE FUEl BED COMPONENTS - E-BOX NOTE: CERAMIC PARTS ARE FRAGIlE. hANDlE wITh CARE ONlY USE ThE CORRECT TYPE AND QUANTITY OF CERAMIC COMPONENTS 9.2 • Place the rear panel against the rear of the box resting AR1362 on the shelf. • Slide one of the side panels into the box ensuring it touches the rear panel. • Gently ease the front edge of the side panel behind the • Place the
