Résumé du contenu de la page N° 1
™
™
Logic E-box
E-Studio &
With upgradable control valve
Instructions for Use,
Installation and Servicing
For use in GB, IE (Great Britain and Eire)
IMPORTANT
The chimney must be swept before installation. Do not attempt to burn rubbish on this fire. This fire must only be operated with
the glass window secured firmly in position. The front casing of this fire will become hot whilst in operation, it is therefore
recommended that a suitable guard should be used for the protection of young child
Résumé du contenu de la page N° 2
• Covering model number 8691CFCHUC and P8691CFCHUC for E-Studio • Covering 8691MCUC 8691PBUC and P8691MCUC P8691PBUC for Logic E-Box CONTENTS PAGE APPLIANCE COMMISSIONING ChECKLIST 3 USER INSTRUCTIONS 4 INSTALLATION INSTRUCTIONS 11 Technical Specification for E-Studio 11 Technical Specification for Logic E-Box 12 Site Requirements 14 Installation 16 Commissioning 23 SERvICING INSTRUCTIONS 24 Servicing Requirements 24 Fault Finding 26 Replacing Parts 28 Spare Parts List for E-Studi
Résumé du contenu de la page N° 3
APPLIANCE COMMISSIONING ChECKLIST IMPORTANT NOTICE Explain the operation of the fire to the end user, hand the completed instructions to them for safe keeping, as the information will be required when making any guaranteed claims. FLUE ChECK PASS FAIL 1. Flue is correct for fire 2. Flue flow test 3. Spillage test GAS ChECK 1. Gas soundness & let by test 2. Standing pressure test mb 3. Fire working pressure (on High Setting) mb NB All other gas fires must be operating on full 3 4. Gas r
Résumé du contenu de la page N° 4
USER INSTRUCTIONS 2.3 If the pilot does not light after repeated attempts, contact 1. GENERAL the retailer or installer from whom the fire was purchased. 2.4 Turn the right-hand control to point to main burner ( ). 1.1 Installation and servicing must only be carried out by a The fire can now be controlled using the left-hand competent person. control knob. 1.2 In all correspondence, please quote the fire type and 2.5 Turn the left-hand control knob to point to low fire ( ), se
Résumé du contenu de la page N° 5
USER INSTRUCTIONS 3 5. CLEanIng THE E-STUdIo MAKE SURE ThE FIRE AND SURROUND ARE COOL BEFORE TRyING TO CLEAN. 5.1 Remove the glass window by unscrewing the four screws in the retaining bracket, Diagram 2. 2 LOGIC E-BOX AR1377 6.3 Remove the ceramic coals and place on a dry, clean surface. Remove the fuel bed and burner cover gasket. 6.4 Clean the burner and tray assembly using a vacuum cleaner with a soft brush attachment, Ensure all debris is removed from the burner ports. 6.5 Replace th
Résumé du contenu de la page N° 6
USER INSTRUCTIONS 7.2 Lean the granite chippings against the burner ledges to disguise the ledges. 7.5 Ensure that the fibre glass window seal on the box is intact. Lower the glass window into the hooks on the box. Secure the window using four screws in the retaining bracket, 5 Diagram 8. 8 AR1769 7.3 Check that the port area. Arrow A, is clear of granite AR1767 chippings. This can be easily done by gently running a screwdriver or similar object along this area. Diagram 6. NOTE: IT IS IMP
Résumé du contenu de la page N° 7
USER INSTRUCTIONS 10 8. LogIC E-Box ARRANGEMENT OF FUEL BED COMPONENTS ADvICE ON hANDLING AND DISPOSAL OF FIRE CERAMICS The fuel effect and side panels in this fire are made from Refractory Ceramic Fibre (RCF), a material which is commonly used for this application. Preventive clothing is not required when handling these AR1359 AR1360 articles, but we recommend you follow normal hygiene rules of not smoking, eating or drinking in the work area, 8.3 Locate the top panel on top of the sides
Résumé du contenu de la page N° 8
USER INSTRUCTIONS 8.9 Place another two medium size coals resting behind the 13 first three coals and against the flame baffle, Diagram 17. 17 AR1363 8.6 There are three sizes of coal used. Small, medium and large. See diagram 14 for identification. AR1366 14 8.10 Place a small coal directly behind the first large coal, and in between the centre of the last two medium coals resting on the flame baffle, Diagram 18. 18 LARGE MEDIUM SMALL AR1379 8.7 Place the single lar
Résumé du contenu de la page N° 9
USER INSTRUCTIONS 23 Pebble Layout 8.12 Position the pebble flame baffle centrally on the tray and ensure the stepped lower edge engages against the rear edge of the burner skin, Diagram 20. 20 A1 A1 A2 AR1409 8.16 Place the remaining two pebbles identified as shown in diagram 24. 24 AR1406 8.13 Place the front pebble piece centrally in the channel at the front of the tray, Diagram 21. 21 A3 A3 AR1410 8.17 The coals/pebbles should evenly cover the whole bed with the gaps between them kept e
Résumé du contenu de la page N° 10
USER INSTRUCTIONS 10. oxygEn dEPLETIon SEnSor The fire is fitted with an oxygen sensitive pilot system that will act to cut off the gas supply to the fire should the oxygen in the room fall below its normal level. If the fire is turned off by this device, it usually indicates that there is a problem with the flue system, and this should be inspected by a qualified engineer. Do not attempt to use the fire until an engineer says it is safe to do so. This device is not a substitute
Résumé du contenu de la page N° 11
INSTALLATION INSTRUCTIONS TEChNICAL SPECIFICATION E-STUdIo models: 8691CFCHUC P8691CFCHUC I I GAS CATEGORy 2H 3P Natural Propane G20 G31 Gas Type 20mbar 37mbar Working Pressure 4.3kW 4.1kW HIGH Gross Input kW 2.5kW 2.3kW LOW 3 0.41 0.153 Gas Rate m /hr 2 2 Efficiency Class 4 4 NO Class x 240 102 Injector Size 6 x 6mm 12mm x 15mm Aeration Size 5” Diameter Min Flue Size 2 Min Flue Size - Pre-cast 90mm x 183mm (16500mm ) Min Flue Specification T260/N2/0/D/
Résumé du contenu de la page N° 12
INSTALLATION INSTRUCTIONS TEChNICAL SPECIFICATION LogIC E-Box models: 8691 MCUC 8691PBUC P8691 MCUC P8616PBUC I I GAS CATEGORy 2H 3P Natural Propane G20 G31 Gas Type 20mbar 37mbar Working Pressure 5.1kW 4.8kW HIGH Gross Input kW 2.5kW 2.5kW LOW 3 0.486 0.181 Gas Rate m /hr 2 2 Efficiency Class 3 3 NO Class x 300 150 Injector Size Coal Pebble Coal Pebble (1) 10mm x 16mm (1) 14mm x 15mm Aeration Size 5mm x 16mm 10mm x 16mm (1) 23mm x 15mm (1) 23mm x 15mm
Résumé du contenu de la page N° 13
INSTALLATION INSTRUCTIONS TEChNICAL SPECIFICATION 190 1 125 oVEraLL ExTErnaL DIMENSIONS SIDE vIEw AR1179 2 Minimum 50mm 125mm MINIMUM DEBRIS COLLECTION SPaCE rEQUIrEMEnTS- (ExISTIng MaSonry CHIMnEyS onLy) AR1178 3 oVEraLL ExTErnaL DIMENSIONS PLAN vIEw AR1206 13 372 550
Résumé du contenu de la page N° 14
INSTALLATION INSTRUCTIONS SITE REQUIREMENTS 1.3 The chimney or flue must be free from any obstruction. 1. FLUE AND ChIMNEy REQUIREMENTS Any damper plates should be removed or secured in the fully open position, and no restrictor plates should be fitted. 1.1 The chimney or flue system must comply with the rules in 1.4 The chimney should be swept immediately prior to the force, and must be a minimum of 125mm (5”) in diameter. installation of the fire - unless it
Résumé du contenu de la page N° 15
INSTALLATION INSTRUCTIONS SITE REQUIREMENTS 2.5 Ensure that no naked flame or incandescent part of the fire If, however, spillage is detected when commissioning the fire, bed projects beyond the vertical plane of the fireplace there may be insufficient natural ventilation and additional opening. ventilation may be required. 2.6 The fire must not be installed in any room that For ventilation requirements in the Republic of Ireland, it will be contains a bath or shower. nec
Résumé du contenu de la page N° 16
INSTALLATION INSTRUCTIONS INSTALLATION TO ChANGE FROM ONE GAS TyPE TO ANOThER A COMPLETE ENGINE ASSEMBLy AND DATA BADGE wILL BE 1. UNPACKING rEQUIrEd. SEE SECTIon 8 SErVICIng InSTrUCTIonS. 4.1 Before installation, ensure that the local distribution 1.1 Remove the fire from its packaging, and check that it is conditions (identification of the type of gas and pressure) complete and undamaged. and the adjustment of the fire are compatible. See 1.2 Put the loose ceramic parts to one s
Résumé du contenu de la page N° 17
INSTALLATION INSTRUCTIONS INSTALLATION 5.3 Decide on the retention method. If cable fixings are to be used remove the lower cover plate by unscrewing the three 6. InSTaLLaTIon oF THE FIrE screws., Diagram 3. 6.1 Ensure that the fireplace opening is in compliance with Section 2 Site Requirements then proceed as follows: A) CABLE RETENTION METhOD 3 6.2 Mark the position of the 4 fixing holes on the rear of the fireplace opening and drill the holes using a 6.5mm masonry dril
Résumé du contenu de la page N° 18
INSTALLATION INSTRUCTIONS INSTALLATION 10 8 AR1157 6.7 Coil up the surplus cable and locate in the back of the 6.14 Turn the appliance off, disconnect the “U” gauge and firebox. replace the sealing screw. Relight the appliance and check NEvER ShORTEN ThE CABLES, ThEy wILL BE REQUIRED the sealing screw for leaks. whEN SERvICING ThE APPLIANCE. 6.8 Replace the lower cover plate. 7. FITTING ThE DECORATIvE INNER Note: The cable adjuster may need to be tucked upward in
Résumé du contenu de la page N° 19
INSTALLATION INSTRUCTIONS INSTALLATION NOTE: IT IS IMPORTANT TO ENSURE THAT THE PANEL 8.3 Check that the port area. Arrow A, is clear of granite LOCATES TIGHTLY AGAINST THE BURNER TRAY. chippings. This can be easily done by gently running a screwdriver or similar object along this area. Diagram 16. 13 16 A AR1931 AR1768 8. E-STUdIo ARRANGEMENT OF FUEL BED NOTE: IT IS IMPORTANT THE GRANITE CHIPPINGS DO COMPONENTS NOT COVER THE PORT AREA IN BETWEEN THE BURNER LEDGES. ONLy USE ThE CORRECT
Résumé du contenu de la page N° 20
INSTALLATION INSTRUCTIONS INSTALLATION ensuring it touches the rear panel. Then gently ease the front edge of the side panel behind the flange so it lies flat 9. LogIC E-Box against the wall of the box. Repeat with the second side ARRANGEMENT OF FUEL BED panel., Diagram 20. COMPONENTS 20 ADvICE ON hANDLING AND DISPOSAL OF FIRE CERAMICS The fuel effect and side panels in this fire are made from Refractory Ceramic Fibre (RCF), a material which is commonly used for this application. Preven
