Résumé du contenu de la page N° 1
Owners &
Installation
Freestanding Gas Stove
Models: F38-NG2
F38-LPG2
PLEASE KEEP THESE INSTRUCTIONS
FOR FUTURE REFERENCE
WARNING:
FOR YOUR SAFETY
Improper installation, adjustment, altera-
What to do if you smell gas:
tion, service or maintenance can cause
Do not try to light any appli-
injury or property damage. Refer to this
ance
manual. For assistance or additional in-
Do not touch any electri-
LISTINGS AND CODE APPROVALS
formation consult an authorized installer,
cal switch: do no
Résumé du contenu de la page N° 2
To the New Owner: Congratulations! You are the owner of a state-of-the-art Gas Stove by FIREPLACE PRODUCTS INTERNATIONAL LTD. The Regency Gas Series of hand crafted appliances has been designed to provide you with all the warmth and charm of a woodstove, at the fl ick of a switch. The models F38-NG2, and F38-LPG2 of this series has been approved by AGA for both safety and effi ciency. As it also bears our own mark, it promises to provide you with economy, comfort and security for many
Résumé du contenu de la page N° 3
TABLE OF CONTENTS MAINTENANCE SAFETY LABEL Safety Label ..................................................................5 Maintenance Instructions ............................................17 Log Replacement ........................................................17 Door and Glass Gasket ...............................................17 INSTALLATION Gold-plated Doors .......................................................17 Glass Replacement ..................................................
Résumé du contenu de la page N° 4
SAFETY LABEL This is a copy of the label that accompanies NOTE: Regency units are constantly being each Freestanding Gas Stove. We have printed improved. Check the label on the unit and if a copy of the contents here for your review. The there is a difference, the label on the unit is the safety label is located on the inside of the drop correct one. down pedestal door. (Australia Only) 4 Regency F38-2 Freestanding Gas Stove
Résumé du contenu de la page N° 5
INSTALLATION IMPORTANT GENERAL GENERAL SAFETY INFORMATION INFORMATION The F38-2 Freestanding Gas Stove must be installed in accordance with these instructions. This installation must conform with local codes 1) The appliance shall be installed in accord- Carefully read all the instructions in this manual ance with the manufacturer's installation or, in the absence of local codes, with AS5601- fi rst. Consult the "authority having jurisdiction" to 2004 (Australia) NZS 5261 (New Zealand). in
Résumé du contenu de la page N° 6
INSTALLATION 14) This unit can be installed on a solid combus- Minimum ceiling CLEARANCES TO tible surface like a wood fl oor as well as on height is 36" / 914 mm carpeting. COMBUSTIBLES from top of unit. The clearances listed below are MINIMUM INSTALLATION distances. Measure the clearance to both the If further reduced clear- appliance and the chimney connector. (The CHECKLIST farthest distance is correct if the two clear- ances are needed, ob- ances do not coincide.) For example, if th
Résumé du contenu de la page N° 7
INSTALLATION 6) When fi nished reading manometer, turn Flueing Requirements System Data off the gas valve, disconnect the hose and F38-2 A100 mm diameter fl ue is required. For cosmetic tighten the screw (clockwise) with a 1/8" fl at screwdriver. Screw should be snug, but do or aesthetic purposes 6" outer fl ue can be used F38-NG2: For 0 to 610 meters altitude as long as an approved inner fl ue is installed. not over tighten. F38-LPG2: For 0 to 610 meters altitude Fasten but do not penetrate t
Résumé du contenu de la page N° 8
INSTALLATION CONVERSION KIT# 731-968 FROM NG TO LPG THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER IF IN DOUBT DO NOT DO THIS CONVERSION !! 9) Insert a 5/32” or WARNING! LPG Conversion Kit Contains: 4mm Allen wrench Also check that the pilot Qty. Part # Description into the hexagonal 1 910-037 LPG Injector and main burner injectors are key-way of the (Pilot Orifi ce) screw (Fig. 2), rotate appropriate for the gas type. 1 904-390 Burner Orifi ce #52 it counter-clockwise 1 908-528
Résumé du contenu de la page N° 9
INSTALLATION 3) Place Rear Log A)02-65 on the two pins on AERATION LOG SET the rear log support. ADJUSTMENT INSTALLATION The burner aeration is factory set but may need Read the instructions below carefully and adjusting due to either the local gas supply or refer to the diagrams. If logs are broken altitude. do not use the unit until they are replaced. Broken logs can interfere with the pilot A)02-65 F38-2 with 38 mj operation. F38-NG2 NG: Full open The gas log kit contains the fol
Résumé du contenu de la page N° 10
G)02-48 INSTALLATION 6) Place the Left Top Log D)02-46 on the pin 9) Place the notch in Center Log F)02-47 over on Log B)02-56 and on top of the cutout Log E)02-45 and across the cutout on Log G)02-48 on Log A)02-65. A)02-65. E)02-45 A)02-65 F)02-47 A)02-65 D)02-46 E)02-45 Side View B)02-56 Bracket C)02-44 The bottom right edge of Log G)02-48 must Notch Cutout sit snugly against the bracket 10) Position notch in Front Right Log G)02-48 11) Test fi re to ensure proper light off (make Cutou
Résumé du contenu de la page N° 11
INSTALLATION 6) Test the seal around the door by placing The smoke should be drawn into the draft di- FRONT DOOR a piece of paper between the unit and the verter. If the smoke is not drawn into the draft door, close the door and try to pull the paper diverter, turn the unit off and check for the cause INSTALLATION out. If it slips out easily, then the door is not of lack of draft. properly sealed. Tighten or loosen the latch. 1) Open the two side panels. See diagram 3. . 2) Slide the door o
Résumé du contenu de la page N° 12
INSTALLATION OPTIONAL WALL OPTIONAL REMOTE FINAL CHECK THERMOSTAT CONTROL Before leaving this unit with the customer, the installer must ensure that the appliance is fi ring A wall thermostat may be installed if desired. Use the Regency Remote Control Kit approved correctly. This includes: Connect the wires as per the wiring diagrams. for this unit. Use of other systems may void Note that the wires are connected to the "TH" your warranty. 1) Clocking the appliance to ensure the cor- on th
Résumé du contenu de la page N° 13
INSTALLATION WIRING No electrical power supply is required for the WARNING: Electrical Grounding CAUTION: gas control to operate. However, a 240V A.C. Instructions Label all wires prior to disconnection power supply is needed for the fan/blower This appliance is equipped with a three when servicing controls. operation. pronged (grounding) plug for your Wiring errors can cause improper protection against shock hazard and and dangerous operation. Caution: Ensure that the wires do not
Résumé du contenu de la page N° 14
OPERATING INSTRUCTIONS 4) Turn the PILOT knob counterclockwise to DO NOT BURN THE APPLIANCE OPERATING pilot and align it with the arrow as shown WITHOUT THE GLASS FRONT IN INSTRUCTIONS in diagram 1. PLACE. Before operating this appliance, proceed through 5) Push in PILOT knob all the way in and hold. Immediately push IGNITOR button until pilot the following check list. AUTOMATIC lights. Continue to hold the PILOT knob in for approximately one minute, then release 1) Read and understan
Résumé du contenu de la page N° 15
OPERATING INSTRUCTIONS COPY OF THE LIGHTING PLATE INSTRUCTIONS
!" # !! $%&'%!$%!!# !( ) ! $* +,,-./0 (*12$!" ") "! ! ! $ */23./.4* "5*167/ ,772$ #+ 5 +1,6/8
Résumé du contenu de la page N° 16
OPERATING INSTRUCTIONS PILOT ADJUSTMENT NORMAL OPERATING SOUNDS OF Periodically check the pilot fl ames. Correct fl ame pattern has three strong blue fl ames: 1 GAS APPLIANCES fl owing around the thermopile and 1 around the thermocouple, and 1 fl owing across the rear of the burner (it does not have to be touching the It is possible that you will hear some sounds from your gas appliance. This is perfectly normal burner). due to the fact that there are various gauges and types of steel used w
Résumé du contenu de la page N° 17
MAINTENANCE MAINTENANCE GLASS CLOTHING OR OTHER FLAMMA- BLE MATERIAL SHOULD NOT BE INSTRUCTIONS REPLACEMENT PLACED ON OR NEAR THE AP- PLIANCE. 1) Always shut the valve off before cleaning. Your Regency heater is supplied with high For relighting, refer to lighting instructions. temperature, 5mm Neoceram silica coated Keep the burner and control compartment ceramic glass that will withstand the highest DO NOT USE THIS APPLIANCE clean by brushing and vacuuming at least heat that your unit w
Résumé du contenu de la page N° 18
MAINTENANCE 4) Lift fan off of the 2 pins, tip back and pull Installing Glass: IMPORTANT through fi rebox opening. Disconnect the Disconnect power supply green ground wire from the left side of the 1) Install both center and side glass onto fan as soon as you can reach it. before servicing aluminium extrusions as per diagram. IMPORTANT: These fans collect a lot of dust from within your home. Ensure you maintain these fan motors on a regular basis by vacuuming out the fan squirrel cages,
Résumé du contenu de la page N° 19
MAINTENANCE REMOVING VALVE If your valve requires maintenance or replace- 4) Remove the two outside frame pieces by 9) Carefully lift the burner tray assembly out. ment, follow these instructions: removing two screws per side. See diagram below. NOTE: Always shut off the gas supply before removing the valve. 1) Open front pedestal door and unhook chain. You may want to put a soft cloth on the base of the unit so that when the pedestal door is open it doesn't scratch the paint. See di
Résumé du contenu de la page N° 20
PARTS LIST F38-2 MAIN ASSEMBLY Part#: Aust. New Zealand Description Aust. New Zealand Description 1) 560-920 Top/Bottom Gold Louvre (Set) 28) * Mounting Bracket - Fan Thermodisc 560-922 Top/Bottom Black Louvre (Set) 29) * Thermodisc Cover 30) 750-026 Rear Panel 2) 750-532 Safety Screen (Australia only) 9) 750-040 Fan Access Door 32) 730-018 Firebox Baffl e 33) 560-535 False Top Assembly 10) 730-034 Gasket for Fan Access Door 34) 590-273 560245 Flue Attachme
