Résumé du contenu de la page N° 1
9” HOT LAMINATOR
Model 92499
OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at: http://www.harborfreight.com
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
© ®
Copyright 2004 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replace
Résumé du contenu de la page N° 2
PRODUCT SPECIFICATIONS Electrical Requirements 110 Volt, 60 Hz, 2 Amps Red LED "Power" Indicator Green LED "Ready" Indicator Motor Type: Synchronous Power Plug Type: 2 Prong Circuit Protection Internal 3.15 Amp Fuse (for replacement by qualified technician only) M" aximum Laminating Width 9 M) aximum Document Thickness .024" (.6mm F" ilm Thickness 0.0030"-0.0040 Laminating Speed Approx. 12" Per Minute Ws arm Up Time 7 to 8 Minute Mt aximum Temperature 300° Fahrenhei Overall Dimensions 13-1/4" L
Résumé du contenu de la page N° 3
WORK AREA 1. Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. Keep the work area well lit. Always keep the work area free of obstructions, grease, oil, trash, and other debris. 2. Do not operate the Laminator in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Electrical equipment creates sparks which may ignite flammables. 3. Keep bystanders, children, and visitors away while operating laminating equipment. Distr
Résumé du contenu de la page N° 4
2. Do not use the Laminator if the Power Switch does not turn it on or off. Any equipment that cannot be controlled with the Power Switch is dangerous and must be replaced. 3. Disconnect the Power Cord Plug from its electrical outlet before making any adjustments, changing accessories, or storing the Laminator. Such preventive safety measures reduce the risk of starting the equipment acciden- tally. 4. Make sure the Laminator has completely cooled before touching it and storing it. 5. Store id
Résumé du contenu de la page N° 5
grounding prong or modify the plug in any way. Do not use any adapter plugs. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. If the tools should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user. 2. Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is grounded. 3. Do
Résumé du contenu de la page N° 6
3. Your tool must be plugged into an appropriate outlet, properly installed and grounded in accordance with all codes and ordinances. The plug and outlet should look like that in the following illustration. (See Figure A.) 3-PRONG PLUG 110 VOLT, GROUNDED, ELECTRICAL OUTLET FIGURE A EXTENSION CORDS 1. Grounded tools require a three wire extension cord. 2. As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized
Résumé du contenu de la page N° 7
4. When using more than one extension cord to make up the total length, make sure each cord contains at least the minimum wire size required. (See Figure B.) 5. If you are using one extension cord for more than one tool, add the nameplate amperes and use the sum to determine the required minimum cord size. (See Figure B.) 6. If you are using an extension cord outdoors, make sure it is marked with the suffix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use. 7. Make sure your ext
Résumé du contenu de la page N° 8
3. Never place objects on top of the Laminator. Always check to make sure the Cooling Vents on top of the Laminator are not obstructed. 4. Turn off the Laminator and unplug it from its electrical outlet before remov- ing any jammed paper or film. 5. The laminating Film (not included) must always be approximately 1/4” longer and wider than the objects being laminated. 6. Use a larger size laminating Film if there is no proper size Film available. After laminating, cut off the excess laminating F
Résumé du contenu de la page N° 9
OPERATING INSTRUCTIONS NOTE: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram on page 11. 1. Extend the two Pull Out Rear Platforms (6). (See Figure D.) 2. Plug the Power Cord (2) into the nearest 110 volt, grounded, electrical outlet. (See Figure D.) POWER CORD (2) RED LED LIGHT (3) GREEN FRONT PLATFORM LED LIGHT (5) (4) POWER SWITCH (1) PULL OUT REAR PLATFORM FIGURE D (6) 3. Turn the Power Switch (1) to its “ON” position. NOTE: The
Résumé du contenu de la page N° 10
5. Place the object to be laminated (i.e., paper, card, etc.) between the two layers of laminating film, and center the object on the laminating film. 6. Make sure the sealed edge of the laminating film is inserted first into the Laminator to avoid jamming. Keep hands and fingers clear of the Adjustable Front Guide (6). 7. Once inserted into the Laminator, the laminating object will be automatically drawn into the Laminator and ejected from the Rear Guide Platform (7). To avoid possible accide
Résumé du contenu de la page N° 11
PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/ OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS
