Résumé du contenu de la page N° 1
510887.qxd 1/21/2004 7:35 PM Page i
012004-510887-(01)
MAX
XL/Pro
Optical Disc Laminator
Connectivity Guide
© 2004 All rights reserved.
Résumé du contenu de la page N° 2
510887.qxd 1/21/2004 7:35 PM Page ii Notices: The information in this document is subject to change without notice. NO WARRANTY OF ANY KIND IS MADE WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. No liability is assumed for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. This document contains proprietary infor
Résumé du contenu de la page N° 3
510887.qxd 1/21/2004 7:35 PM Page iii Table of Contents Optical Disc Laminator Guide .....................................................................................1 A. Unpacking and Inspection ...............................................................................1 B. Installing the Laminator Software Driver......................................................1 C. Connecting the Laminator to Your Duplicator .............................................3 D. Creating Discs with
Résumé du contenu de la page N° 4
510119pdf.qxd 5/29/2002 11:14 AM Page iv Interactive Feature in this PDF Document There are interactive features that will allow you to jump to different locations within the document. Each listing in the Table of Contents is interactive. Place the cursor on either the words or the page number. A small hand with a pointing finger icon appears. Click on the line with the icon and the document will jump to that page. If you want to return to the Table of Contents, move the icon to the top of t
Résumé du contenu de la page N° 5
510887.qxd 1/21/2004 7:35 PM Page 1 Optical Disc Laminator Connection Guide THANK YOU… Thank you for purchasing the Optical Disc Laminator Connectivity Kit. This kit will allow you to use your Optical Disc Laminator in conjunction with the Pro, XL and MAX versions of Optical Disc Duplicators. This guide will explain the connection of the Laminator to these systems, the installation of software and the running of disc jobs. A. UNPACKING AND INSPECTION While unpacking your Laminator Connect
Résumé du contenu de la page N° 6
510887.qxd 1/21/2004 7:35 PM Page 2 e. Make certain the Laminator has been plugged into power and turned on. f. Select "Install Software Automatically" and click Next. 2 Optical Disc Laminator Connectivity Guide
Résumé du contenu de la page N° 7
510887.qxd 1/21/2004 7:35 PM Page 3 g. You may see a notice like the one shown here stating that the Accent Disc Laminator has not passed Windows Logo Testing. Click the Install Anyway button to continue installing the printer driver for your Laminator. Once the driver has finished installing, click the Finish button. This will install an update to your PrimoDVD software and will reboot your system. C. CONNECTING THE LAMINATOR TO YOUR DUPLICATOR MAX Your Laminator connects easily to a Duplica
Résumé du contenu de la page N° 8
510887.qxd 1/21/2004 7:35 PM Page 4 The following steps describe in detail how to connect the Laminator to your DuplicatorMAX: a. Connect the Laminator Stand to the left hand side of the DuplicatorMAX as shown: b. Remove the Input Bin closest to the Laminator Stand to make room for the Laminator's disc tray. c. Place the Laminator on the stand using the Locating Pegs to align the Laminator properly. d. Connect your Laminator to the PC using the provided USB Cable. e. The Laminator must now b
Résumé du contenu de la page N° 9
510887.qxd 1/21/2004 7:35 PM Page 5 5) From the Main Application Screen click Robotics then Options. 6) Enable the Use Laminator checkbox. 7) Click the button labeled Move to (Calibrate). This will move the Picker Mechanism to the Laminator Tray position. 8) Lower the disc to the Laminator Tray Position as follows: a) Press and hold the Sequence and Pick buttons simultaneously for 5 seconds to enter calibration mode. The LEDs on the front of the DuplicatorMAX will flash back and forth indic
Résumé du contenu de la page N° 10
510887.qxd 1/21/2004 7:35 PM Page 6 b) While the LEDs are flashing, press the Pause button. The Picking Mechanism will lower to the Laminator Tray Position. Press Pause to Lower Mechanism to Laminator Tray Position c) Adjust the Laminator Tray forward and back by loosening the adjusting screws located towards the front of the stand. d). For left-to-right adjustment, nudge the Picker Mechanism left by pressing the Pause Button or nudge it right by pressing the Sequence Button. End Cali
Résumé du contenu de la page N° 11
510887.qxd 1/21/2004 7:35 PM Page 7 f) Tighten the Adjusting Screws on the front of the Laminator Stand to lock the stand in position. 9. You have now calibrated your Laminator to the Duplicator MAX and are ready to produce discs! D. CREATING DISCS WITH YOUR DUPLICATOR MAX IN PRIMO Laminating your disc jobs is very simple. This is done as follows: 1. From the Main Application Screen click Robotics then Options. Enable the Use Laminator checkbox as shown: 2. Set up your print and record job
Résumé du contenu de la page N° 12
510887.qxd 1/21/2004 7:35 PM Page 8 The Laminator is positioned at the front left corner of the Duplicator. The optional Duplicator XL/Pro Laminator Stand is needed for both of these configurations. The stand is shown here: STAND-ALONE MODE The Automated Stand-Alone Mode allows you to connect the Laminator to the Duplicator XL or DuplicatorPro without connecting either the Duplicator or Laminator to a PC. This mode is used when you simply want to load the Duplicator with 100 printed discs a
Résumé du contenu de la page N° 13
510887.qxd 1/21/2004 7:35 PM Page 9 4. Connect the Laminator Stand to the back of the Laminator as shown: 2 1 5. Place the Laminator on the Laminator Stand as shown: There are two sets of holes on the underside of your Laminator. Set the Laminator on the stand locating the smaller set of holes on the metal locating pegs on the Laminator Stand. Make certain the Laminator's rubber feet are resting on the stand and not in the four large holes in the stand. Optical Disc Laminator Connectivity G
Résumé du contenu de la page N° 14
510887.qxd 1/21/2004 7:35 PM Page 10 6. Connect the Auxiliary Control Cable and Power Cable the Laminator as shown: 7. Align the Laminator's tray position to the picker. This is done as follows: a. Make certain the Laminator has power and is turned on. b. Load a disc into the Input Bin. This is the Bin on the right side of the Duplicator. c. If the Laminator Tray is not in the OUT position, press the Laminate button to eject the Laminator Disc Tray. d. Press the Sequence button on the fron
Résumé du contenu de la page N° 15
510887.qxd 1/21/2004 7:35 PM Page 11 8. The Laminator is now aligned properly. Once the Laminator's Heat Roller has achieved proper operating temperature (indicated by a solidly lit Ready LED on the Laminator's Control Panel), you are ready to laminate discs. Load the input bin with discs and press the Laminate button. Discs will be automatically picked from the input bin, loaded into the laminator, and deposited in the output bin when finished. This will repeat until the Input Bin is empt
Résumé du contenu de la page N° 16
510887.qxd 1/21/2004 7:35 PM Page 12 4. Place the Laminator on the stand. The Laminator will need to be placed on the stand with the Laminator's rubber feet resting in the four holes located on the top of the Stand as shown: 5. Using the provided USB Cable, connect the Laminator to your PC as shown: 6. Align the Laminator's Disc Tray position for proper picking and placement of discs. This is done as follows: a. Make certain the Laminator has power and is turned on. b. Load a disc into th
Résumé du contenu de la page N° 17
510887.qxd 1/21/2004 7:35 PM Page 13 c. If the Laminator Tray is not in the OUT position, press the Laminate button to eject the Laminator Disc Tray. d. From the Main Application Screen click Robotics then Options. e. Enable the Use Laminator checkbox. f. Click the button labeled Move to (Calibrate). This will move the Picker Mechanism to the Laminator Tray position. g. Press and hold the Pick button on the front of the Duplicator for 5 seconds. The disc should automatically and hover just
Résumé du contenu de la page N° 18
510887.qxd 1/21/2004 7:35 PM Page 14 8. From the Main Application Screen click Robotics then Options. Select Lamination as shown: 9. Set up your print and record job as you normally would per the Duplicator XL/Pro User's Manual. 10. Click the red circle Record button to start your job! 14 Optical Disc Laminator Connectivity Guide
Résumé du contenu de la page N° 19
510887.qxd 1/21/2004 7:35 PM Page 15 F. TROUBLESHOOTING Problem Resolution Will not Laminate • Check Power to the Laminator • Make sure that the Ready LED is on and steady indicating the Laminator's Heat Roller has achieved normal operating Temperature I do not see an option • In PrimoDVD, click Robotics then in PrimoDVD to Options. You should see a laminate discs Laminate check box.· • If you do not see this option in the Robotic Options dialog box, install the software on the instal
Résumé du contenu de la page N° 20
510887.qxd 1/21/2004 7:35 PM Page 16 Printed in the United States of America P/N 510887
