Résumé du contenu de la page N° 1
If you have questions or comments, contact us.
Pour toute question ou tout commentaire, nous contacter.
Si tiene dudas o comentarios, contáctenos.
1-800-4-De WALT • www.dewalt.com
InstructIon ManuaL
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA
GuIDe D'utILIsatIon DE GARANTÍA. aDVertencIa: LÉASE ESTE INSTRUCTIVO ANTES
DE USAR EL PRODUCTO.
ManuaL De InstruccIones
DPD3100
Pressure Washer
Laveuse à pression
Lavadora a presión
Résumé du contenu de la page N° 2
B C FIG. 1 A DPD3100 Pressure Washer P A. Panel assembly I. Starter grip O L N B. Nozzle holder J. Engine C. Professional Spray gun K. Choke control K M D. Side Handle L. Throttle control lever E. Quick-connect M. Fuel valve lever Q spray wand N. Gas cap F. Frame O. Handle assembly D G. Engine dipstick/oil plug P. High-pressure hose H. Engine switch J Q. High-pressure pump E I F Engine Refer to the engine instruction manual for location and operation of other engine controls. G P
Résumé du contenu de la page N° 3
English Specifications MoDeL WeIGht heIGht WIDth LenGth PsI Max* aVera Ge GPM Max* aVera Ge enGIne oP erat InG oP erat InG PsI GPM DPD3100 83.6 lbs 26.5" 23" 40" 3100 2780 2.8 2.7 De WALT (21373 kPa) (19167 kPa) (10.6 L/min) (10.3 L/min) 196 cc OHV, 5.5 Net HP, 6.5 Gross HP ** * Maximum PSI and GPM ratings determined in accordance with the Pressure Washers Manufacturers Association (PWMA) standard PW101 ** Horsepower rating (shown as maximum output @ 3600 rpm) is in accordance with SAE J
Résumé du contenu de la page N° 4
7. Do not overreach or stand on unstable support. Keep good footing and balance at all times. 8. Follow the maintenance instructions specified in the manual. DANGER: RISk Of I Nj ECTION OR SEvERE INj URy. kEEP DANGER: RISk Of Ex Pl OSION OR f IRE ClEAR Of NOzzlE. DO NOT DIRECT DISChARGE STREAm AT What can happen how to prevent it PERSONS. ThIS PRODUCT IS TO BE USED ONly By T RAINED OPERATORS. • S p i l l e d g a s o l i n e a n d i t ’ s • S h u t o f f e n g i n
Résumé du contenu de la page N° 5
English • Muffler e xhaust heat can • A l w a y s k e e p p r e s s u r e w a s h e r DANGER: RISk TO BREAThING (ASPhyxIATION) CONTINUED damage painte d surf ac es, a mini m um of 4' (1.2 m) away melt any material sensi tive from surf ace s (such as • S o m e c l e a n i n g f l u i d s • Use only cleaning fluids to heat (such as siding, houses, aut o mob iles or con tain substanc es which specif i cal ly recom mend ed could cause injury to skin,
Résumé du contenu de la page N° 6
DANGER: RISk Of flUID INjECTION AND lACERATION CONTINUED • Y o u r p r e s s u r e w a s h e r • D i r e c t s p r a y a w a y f r o m s e l f DANGER: RISk Of INjUR y fROm SPRAy operates at fluid pressures and others. What can happen how to prevent it and velocities high enough to • M a k e s u r e h o s e a n d f i t t i n g s penetrate human and • H i g h - v e l o c i t y f l u i d s p r a y • A l w a y s w e a r A N S I - a p p r o v e
Résumé du contenu de la page N° 7
English • If proper star ting procedure • If engine does not star t after is not followed, engine can two pulls, squeeze trigger kickback causing serious of gun to relieve pump DANGER: RISk Of UNSAfE OPERATION hand and arm injury. pressure. Pull starter cord slowly until resistance is felt. What can happen how to prevent it Then pull cord rapidly to avoid • Unsaf e oper a tion of y our • Do not use chlor ine kickback and prevent hand or pressure wash
Résumé du contenu de la page N° 8
DANGER: RISk Of I Nj URy OR PROPE R Ty DAmAGE WhEN WARNING: RISk Of B URSTING TRANSPORTING OR STORING What can happen how to prevent it What can happen how to prevent it • Over inflation of tires could • Use a tire pressure gauge to • F u e l o r o i l c a n l e a k o r s p i l l • If pressure w asher is equipped result in serious injury and check the tires pressure before and could result in fire or with a fuel shut-off valve, turn property damage. each use
Résumé du contenu de la page N° 9
English WARNING: RISk Of ElEC TRI CAl ShOCk WARNING: RISk Of hOT SURf ACES What can happen how to prevent it What can happen how to prevent it • S p r a y d i r e c t e d a t e l e c t r i c a l • U n p l u g a n y e l e c t r i c a l l y • Con tact with hot surf ac es , • D u r i n g o p e r a t i o n , t o u c h outlets or switches , or obj ects op era t ed product before such as engines exhaust only the control surfaces con nec
Résumé du contenu de la page N° 10
note: The high pressure pump is maintenance free and requires InSTALLATIon no oil, if there is a problem with the pump contact a De WALT factory Pressure Washer Assembly (Fig. 1) service center, a De WALT authorized service center or other qualified 1. Place handle assembly (O) onto frame, depress service personnel. the snap buttons, and slide the handle assembly WARNING: Risk of bursting. Use a tire pressure gauge to check the onto the frame (F) until snap buttons are secured tires press
Résumé du contenu de la page N° 11
English chanGInG nozzLes on sPray WanD nozzle color spray Pattern uses surfaces* DANGER: Risk of fluid injection. Do not direct discharge stream 0˚ powerful metal or toward persons, unprotected skin, eyes or any pets or animals. pinpoint for concrete; Serious injury will occur. red very intense DO NOT use WARNING: Flying objects could cause risk of serious injury. DO cleaning on wood NOT attempt to change nozzles while pressure washer is running. Turn engine off before changing nozzles. 15
Résumé du contenu de la page N° 12
3. Install low-pressure (black) nozzle into quick connect fitting of spray • DO NOT let hoses come in contact with very hot engine wand, refer to spray Wand nozzles. note: Chemicals and soaps muffler during or immediately after use of your pressure will not siphon if the black soap nozzle is not installed on the washer. Damage to hoses from contact with hot engine spray wand. surfaces will NOT be covered by warranty. 4. After use of chemicals, place chemical hose into container of clean
Résumé du contenu de la page N° 13
English 4. Verify the filter screen (U) is in water inlet of pump. 13. WARNING: Risk of unsafe operation. Pull starter grip slowly The cone side faces out. until resistance is felt. Then pull starter grip (I) rapidly to avoid kickback and prevent hand or arm injury. 5. Connect the cold water source (V) to pump inlet. note: Do not allow the starter grip to snap back. Return it gently note: Water source must provide a minimum of by hand. 5 gallons per minute at 20 PSI (138 kPa). WARNIN
Résumé du contenu de la page N° 14
CAUTION: Risk of property damage Failure to do so could cause Pump damage to the pump. The high pressure pump is maintenance free and requires no oil, if 2. Place the engine ON/OFF switch (H) to the OFF Position. there is a problem with the pump contact a De WALT factory service 3. Place the fuel valve lever (M) in the OFF center, a De WALT authorized service center or other qualified ser- postion. vice personnel. CAUTION: Risk of property damage. Never nozzle cleaning turn water supply
Résumé du contenu de la page N° 15
English 1. Obtain a funnel, 6 oz. (170 mL) of RV antifreeze and 16–36" 1. Remove the filter screen (U) by grasping the end and removing it from water inlet of (40–91cm) of garden hose with a male hose connector attached pump. to one end. 2. Clean filter by flushing it with water on both CAUTION: r i s k o f p r o p e r t y d a m a g e . U s e o n l y r v a n t i f r e e z e . A n y sides. other anti freeze is corrosive and can damage pump. 3. Reinsert filter into water
Résumé du contenu de la page N° 16
CAUTION: Risk of personal injury. Avoid placing hands between Limited Warranty handle and frame when assembling to prevent pinching. De WALT pressure washers are warranted for two years from the date of purchase. De WALT will repair, without charge, any defects AccESSorIES due to faulty materials or workmanship. This warranty does not Recommended accessories for use with your tool are available for cover parts that are damaged through misuse or abuse, or parts purchase from your local dea
Résumé du contenu de la page N° 17
English Free W arnInG LaBeL rePLaceMent : If your warning labels Glossary (next page) become illegible or are missing, call 1-800-4-De WALT Bypass mode: Allows water to re-circulate within pump when the for a free replacement. gun trigger is not pulled. chemical hose: Feeds cleaning agents into the pump to mix with the water. Refer to Chemicals and Cleaning Solvents. chemical injection system: Mixes cleaners or cleaning solvents with water to improve cleaning effectiveness. choke control:
Résumé du contenu de la page N° 18
Troubleshooting Guide This section provides a list of the more frequently encountered malfunctions, their causes and corrective actions. The operator or maintenance personnel can perform some corrective actions, and others may require the assistance of a qualified De WALT technician or your dealer. Problem code Engine will not start ......................................................................................................1, 2, 3, 4, 5, 6, 7, 8, 29 (refer to the engine's instruct
Résumé du contenu de la page N° 19
English (Troubleshooting codes cont.) coDe PossIBLe cause PossIBLe soLutIon 10 Low water supply. Water supply must be at least 5 GPM @ 20 PSI (138 kPa). 11 Leak at high-pressure hose fitting. Repair leak. Apply sealant tape if necessary. 12 Nozzle obstructed. See nozzle cleaning under Maintenance. 13 Water filter screen clogged. Remove and clean filter. 14 Air in hose. Turn off the engine, then the water source. Disconnect the water source from the pump inlet and turn the water source on to
Résumé du contenu de la page N° 20
(Troubleshooting codes cont.) coDe PossIBLe cause PossIBLe soLutIon 26 Loose hose connection. Tighten. 27 Piston packings worn. Have replaced by authorized service center. 28 Pump head or tubes damaged from freezing. Have replaced by authorized service center. 29 Air filter filled with oil. Clean air filter element. Refer to engine instruction manual for correct procedure. 20 English
