Résumé du contenu de la page N° 1
BUFFING SYSTEM
MODEL G1061/G1061Z
INSTRUCTION MANUAL
COPYRIGHT © 1992 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
JANUARY, 2002 PRINTED IN TAIWAN.
Résumé du contenu de la page N° 2
WARNING Some dust created by power sanding, sawing, grind- ing, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. • Crystalline silica from bricks, cement, and other masonry products. • Arsenic and chromium from chemically treated lumber. Your risk from these exposures varies, depending on how often you do this type of w
Résumé du contenu de la page N° 3
Table Of Contents PAGE 1. SAFETY SAFETY RULES FOR POWER TOOLS ..............................................................2-3 ADDITIONAL SAFETY INSTRUCTIONS FOR BUFFERS ......................................4 2. CIRCUIT REQUIREMENTS 110V OPERATION ..................................................................................................5 EXTENSION CORDS ..............................................................................................5 GROUNDING ............................
Résumé du contenu de la page N° 4
SECTION 1: SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures. I
Résumé du contenu de la page N° 5
Safety Instructions For Power Tools 9. USE PROPER EXTENSION CORD. Make 16. REDUCE THE RISK OF UNINTENTION- sure your extension cord is in good condi- AL STARTING. On machines with magnet- tion. Conductor size should be in accor- ic contact starting switches there is a risk of dance with the chart below. The amperage starting if the machine is bumped or jarred. rating should be listed on the motor or tool Always disconnect from power source nameplate. An undersized cord will cause before adjustin
Résumé du contenu de la page N° 6
Additional Safety Instructions For Buffers 1. ALWAYS WEAR EYE PROTECTION! 7. DO NOT allow your hands to come into contact with sanding drums or buffing 2. WEAR AN APPROVED DUST MASK wheels during operation. Abrasive acces- OR RESPIRATOR. Buffing operations sories have the ability to remove a lot of produce dust. material, including skin, very quickly. 3. MAKE SURE BUFFER IS SECURED 8. ANY PROBLEM concerned with any FIRMLY TO A BENCH OR STAND moving parts or accessories must be BEFORE USE. Any “w
Résumé du contenu de la page N° 7
SECTION 2: CIRCUIT REQUIREMENTS 110V Operation This equipment must be grounded. Verify that any The Model G1061/G1061Z is wired for 110/120V. existing electrical outlet The 1 H.P. motor will safely draw 10 amps at and circuit you intend to 110V. If you operate this machine on any circuit plug into is actually that is already close to its capacity, it might blow grounded. Under no cir- a fuse or trip a circuit breaker. However, if an cumstances should the unusual load does not exist and a power f
Résumé du contenu de la page N° 8
SECTION 3: INTRODUCTION Most importantly, we stand behind our machines. Commentary If you have any service questions or parts requests, please call or write us at the location listed below: We are proud to offer the Grizzly Model Grizzly Industrial, Inc. G1061/G1061Z Buffing System. The Model 1203 Lycoming Mall Circle G1061/G1061Z is part of a growing Grizzly family Muncy, PA 17756 of fine woodworking machinery. When used Phone: (570) 546-9663 according to the guidelines set forth in this manu-
Résumé du contenu de la page N° 9
Unpacking Mounting The Model G1061/G1061Z is shipped from the The Model G1061/G1061Z weighs approximately manufacturer in a carefully packed carton. If you 59 lbs. Make sure the workbench on which you discover the machine is damaged after you have plan to mount the buffer is sturdy enough to hold signed for delivery, immediately call Customer the weight of the machine and any downward Service for advice. pressure that may be applied during operation. The workbench should have a level surface an
Résumé du contenu de la page N° 10
SECTION 6: OPERATIONS Test Run Keep loose clothing rolled up and out of the way of machinery and Once mounting is complete and adjustments are keep hair pulled back. done to your satisfaction, you are ready to test the machine. Turn on the power supply at the main panel. Make sure that your hand is poised near the Disconnect power to the switch in case there is a problem. The buffer machine when perform- ! should run smoothly with little or no vibration or ing any maintenance, rubbing noises. St
Résumé du contenu de la page N° 11
5. Start the buffer and with both hands firmly Buffing & Polishing grasp the item to be polished. Lightly and evenly move the workpiece back and forth on the buffing wheel. Be careful when polishing For buffing and polishing, Grizzly offers a broad plated metals; there is a chance that the thin line of buffing wheels and polishing compounds. plated material may be damaged. A light Please refer to our current catalog. To buff or pol- pressure is all that is needed for quality work. ish: 1. Make s
Résumé du contenu de la page N° 12
4. Inflate the drum using a bicycle pump or air Accessory Removal compressor. The maximum air pressure is 10 psi. DONOT OVER-INFLATE! We recom- mend against filling the drum with an air com- pressor. When sanding drums have been To remove the buffing or sanding attachments, installed, the assembly should look similar to ensure that the switch is pushed in and the power Figure 3. cord is disconnected. With buffing wheels mount- ed, hold the shaft with one hand while loosening the nut with a wrenc
Résumé du contenu de la page N° 13
SECTION 7: MAINTENANCE Miscellaneous Disconnect power to the machine when perform- ! ing any maintenance, Always be aware of the condition of your buffer. assembly or adjust- Routinely check the condition of the following ments. Failure to do this items and repair or replace as necessary: may result in serious personal injury. • Loose mounting bolts • Worn switch Lubrication • Worn or damaged cord • Worn or damaged support bearings or guide Shielded and pre-lubricated ball bearings require beari
Résumé du contenu de la page N° 14
SECTION 8: CLOSURE The following pages contain general machine We recommend you keep a copy of our current data, parts diagrams/lists, a troubleshooting guide catalog for complete information regarding and Warranty/Return information for your Model Grizzly's warranty and return policy. If you need G1061/G1061Z. additional technical information relating to this machine, or if you need general assistance or If you need parts or help in assembling your replacement parts, please contact the Service
Résumé du contenu de la page N° 15
MACHINE DATA SHEET Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 GRIZZLY MODEL G1061/G1061Z BUFFING MACHINE Design Type.................................................................................................... Bench Model Overall Dimensions: 1 Height ....................................................................................................................11 ⁄4" 1 Width................................................................
Résumé du contenu de la page N° 16
Ref# Part# Description Ref# Part# Description 001 P1061001 MOTOR BASE 016 P1061016 PANEL SWITCH 3 002 P1061002 MOTOR CASE 017 PLW03 LOCK WASHER ⁄16" 5 1 003 PFH07 FLAT HD SCR ⁄16"-18 X 1 ⁄4" 018 P1061018 ON/OFF SWITCH 5 004 P1061004 STATOR (G1061) 019 PLW01 LOCK WASHER ⁄16" 5 004 P1061Z004 STATOR (G1061Z) 020 PN02 HEX NUT ⁄16"-18 005 P1061005 ROTOR W/#6 (G1061) 021 PHTEK1 SELF TAP PHLP HD SCR 005 P1061Z005 ROTOR (G1061Z) 022 P1061022 CLAMP 007 P1061007 MOTOR FAN 023 PC400 CAPACITOR 008 P6206 BA
Résumé du contenu de la page N° 17
NOTES: G1061/G1061Z Buffing System -15-
Résumé du contenu de la page N° 18
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty and any and all warranties that may be implied by law, including any merchantability or fitness, for any par- ticular purpose, are hereby limited to th
Résumé du contenu de la page N° 19
WARRANTY CARD Name ____________________________________________________________________________________ Street ____________________________________________________________________________________ City ______________________________________________________________State________Zip_________ Phone Number_______________________E-Mail_______________________FAX________________________ MODEL # G1061/G1061Z Buffing System Order #______________________________________________ The following inform
Résumé du contenu de la page N° 20
FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 FOLD ALONG DOTTED LINE Send a Grizzly Catalog to a friend: Name_______________________________ Street_______________________________ City______________State______Zip______ TAPE ALONG EDGES--PLEASE DO NOT STAPLE
