Résumé du contenu de la page N° 1
4-1/2” ANGLE GRINDER
Model 95578
ASSEMBLY AND OPERATING INSTRUCTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at: http://www.harborfreight.com
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
©
®
Copyright 2006 by Harbor Freight Tools . All right reserved. No portion of this
manual or any artwork contained herein may be reproduc
Résumé du contenu de la page N° 2
PRODUCT SPECIFICATIONS Item Description Electrical 120 VAC / 60 Hz / 4.2 Amps / 11,000 RPM Requirements Power Cord Type: 18 AWG x 2C / 6’ Long Power Plug Type: 2-Prong / Polarized Power Switch Type: Toggle (ON/OFF) Spindle Size 5/8”-11 TPI with 7/8” Arbor Adapter Required 4-1/2” Diameter Grinding Wheel Size 1/4” Thick (Not Included) 7/8” Spindle Hole Side Handle 4-1/2” Long x 2-1/4” O.D. Dimensions Overall 10-1/8” Long x 8” Wide x 3-3/4” High Dimensions (with Side Handle) Net Wei
Résumé du contenu de la page N° 3
ELECTRICAL SAFETY 4. Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the plug in any way. Do not use any adapter plugs. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. If the tools should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user. 5. Double insu
Résumé du contenu de la page N° 4
in. Carrying power tools with your finger on the Power Switch, or plugging in power tools with the Power Switch on, invites accidents. 13. Remove adjusting keys or wrenches before turning the power tool on. A wrench or a key that is left attached to a rotating part of the power tool may result in personal injury. 14. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the power tool in unexpected situations. 15. Use safety equi
Résumé du contenu de la page N° 5
model. Accessories that may be suitable for one tool may become hazardous when used on another tool. SERVICE 24. Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury. 25. When servicing a tool, use only identical replacement parts. Follow instructions in the “Inspection, Maintenance, And Cleaning” section of this manual. Use of unauthorized parts or failure to follow maintenance instructi
Résumé du contenu de la page N° 6
8. Use only 4-1/2” diameter grinding wheels (not included) having a 7/8” center spindle hole. Never disable or modify the Wheel Guard (4). 9. Avoid unintentional starting. Make sure you are prepared to begin work before turning on the Angle Grinder. 10. Do not force the Angle Grinder. This tool will do the work better and safer at the speed and capacity for which it was designed. Do not force the rotating grinding wheel (not included) into the object being ground. Apply moderate pressure,
Résumé du contenu de la page N° 7
and other construction activities, contain chemicals known (to the State of Cali- fornia) to cause cancer, birth defects or other reproductive harm. Some ex- amples of these chemicals are: lead from lead-based paints, crystalline silica from bricks and cement or other masonry products, arsenic and chromium from chemically treated lumber. Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated
Résumé du contenu de la page N° 8
to an electrically “live” terminal. (See Figure A.) 3. Your tool must be plugged into an appropriate outlet, properly installed and grounded in accordance with all codes and ordinances. The plug and outlet should look like those in the following illustration. (See Figure A.) THIS PRODUCT 120 VOLT, DOES NOT GROUNDED, USE A ELECTRICAL OUTLET 3-PRONG PLUG FIGURE A DOUBLE INSULATED TOOLS: TOOLS WITH TWO PRONG PLUGS 4. Tools marked “Double Insulated” do not require grounding. They have a special
Résumé du contenu de la page N° 9
EXTENSION CORDS 1. Grounded tools require a three wire extension cord. Double Insulated tools can use either a two or three wire extension cord. 2. As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible tool damage. (See Figures C.) 3. The smaller the gauge number of the wire, the greater the capacity of the cord. For example, a 14
Résumé du contenu de la page N° 10
SYMBOLOGY FIGURE D UNPACKING When unpacking, check to make sure all the parts shown on the Parts List on page 14 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. ASSEMBLY INSTRUCTIONS NOTE: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram on page 14. 1. CAUTION! Always make sure the PowerSwitch (41) for the Angle Grinder is in i
Résumé du contenu de la page N° 11
install the convex (rounded outward) side of the Grinding Wheel toward the Spindle (7). (See Figure E.) 3. Screw the Outer Flange Nut (1) onto the Spindle (7). Depress and hold the Lock Pin (22) to keep the Spindle from turning. Then, use the provided Wrench (51) to firmly tighten the Outer Flange Nut onto the Spindle. (See Figure E.) A B C GRINDING WHEEL LOCK PIN (22) WRENCH (51) SPINDLE (7) OUTER OUTER FLANGE FLANGE NUT NUT (1) (1) FIGURE E To Attach The Side Handle: 1. The Side Handle (18
Résumé du contenu de la page N° 12
2. Grip the Angle Grinder firmly with both hands. Then turn the Power Switch (41) to its “ON” position to start the Grinder. (See Figure G.) o o 3. Hold the Angle Grinder at an angle of 10 to 15 to the work surface. When only the outer edge of the grinding wheel is used, a rough cut surface will result. If the grinding wheel is pressed flat against the workpiece, the grinding action will be irregular or bumpy and the tool will be difficult to control. (See Figure G.) 4. Do not force the r
Résumé du contenu de la page N° 13
4. To clean or replace the Carbon Brushes (38): It may become necessary to clean or replace the two Carbon Brushes when the Motor performance de- creases, or stops working completely. The Carbon Brushes are located on each side of the Motor Housing (40). To do so, remove the two Brush Holder Covers (37). Then, remove the two Carbon Brushes from the Brush Holders (39). If the Carbon Brushes are worn down more than 1/2, replace both Carbon Brushes. If, however, the Carbon Brushes are just di
Résumé du contenu de la page N° 14
PARTS LIST AND ASSEMBLY DIAGRAM Part # Description Part # Description Part # Description 1 Outer Flange Nut 18 Side Handle 35 Spring 2 Spring Washer 19 Screw 36 Wind Shield Ring 3 Inner Flange 20 Keeper 37 Brush Holder Cover 4 Wheel Guard 21 Lock Spring 38 Carbon Brush (#100, Qty. 2) 5 Screw 22 Lock Pin 39 Brush Holder (#100) 6 Nut 23 Shell Head 40 Motor Housing 7 Spindle 24 Pinion Gear 41 Power Switch 8 Woodruff Key 25 Bearing 6018 42 Switch Mount 9 Screw 26 Gearbox Back Cover 43 Screw
Résumé du contenu de la page N° 15
IMPORTANT WARRANTY INFORMATION LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of ninety days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, or t
