Instruction d'utilisation Invacare 1034177

Résumé du contenu de la page N° 1

PATIENT OPERATED WHEEL LOCKS
FOR 2000/4000 RECLINER WHEELCHAIRS
KIT NUMBERS 1034177
Installation, Assembly and Operating Instructions
NOTE: Check ALL parts for shipping damage. In case 3. Remove the existing tube clamp from the wheel-
of shipping damage, DO NOT use. Contact Carrier/ chair frame.
Dealer for further instruction.
4. Install the plug button into end of the NEW pivot
arm assembly.
SAFETY SUMMARY
5. Insert the NEW strap and stud assembly through
The following recommendations are made

Résumé du contenu de la page N° 2

Back Tube 2-inch Plug Button (STEP 6) Mounting Screw (STEP 4) (STEPS 2,7) Heavy Locknut Pivot Arm Assembly Washer (STEPS 1,11) (STEPS 1,4,5,9,10,12) (STEP 12) DETAIL “A” Axle Lug 3/4-inch (STEP 10) Mounting Screw (STEP 12) Wheelchair Frame Wheel Lock Assembly Locknut Tube Clamp (STEP 12) (STEP 5) (STEPS 3,6,7) Bushing (STEPS 2,5,7) Strap/Stud Assembly (STEPS 2,7) Axle Mounting Screw (STEPS 1,10,11) Pivot Arm Thin Washer (STEPS 2,7) Spacer Rear Wheel (STEPS 1,9,10) Locknut (STEPS 1,10) (STEPS 2,8

Résumé du contenu de la page N° 3

ADJUSTING THE PATIENT USING THE PATIENT OPERATED OPERATED WHEEL LOCKS THE WHEEL LOCKS (FIGURE 3) (FIGURE 2) WARNING NOTE: Refer to INSTALLATION WARNINGS in the DO NOT attempt to stop a moving wheelchair SAFETY SUMMARY in this instruction sheet. with the wheel locks. WHEEL LOCKS ARE NOT BRAKES. NOTE: If wheels are pneumatic, before adjusting or replacing the wheel lock assemblies, ensure that the 1. Ensure the wheelchair is not moving before en- tires are inflated to the recommended psi on the si

Résumé du contenu de la page N° 4

8. Install the plug button into end of pivot arm assembly. CONVERTING FROM ATTENDANT 9. Insert the strap and stud assembly through the pivot OPERATED WHEEL LOCKS arm assembly and secure with locknut. (FIGURE 4) 10. Install the tube clamp over the frame and mea- NOTE: Refer to INSTALLATION WARNINGS and sure 4-3/16-inches from the back tube of the frame CAUTIONS in the SAFETY SUMMARY in this instruc- assembly to the center of the tube clamp. tion sheet. 11. Insert the 2-inch mounting screw through

Résumé du contenu de la page N° 5

STEPS 1-6 Locknut Locknut Attendant Operated (STEPS 2,6) (STEPS 2,6) Wheel Lock BackTube (STEPS 1,4,5) Mounting Recliner Tube Locking Rod Bracket (STEPS 1,5,6) (STEPS 2-6) (STEPS 2,6,) Bolt and Locknut (STEP 1) Anti-Rattle (STEPS 3,5,6) Mounting Screw Recliner Tube (STEPS 2,6,) (STEPS 1,5,) STEP 7 Wheelchair Frame Locknut Rear Wheel Axle Mounting Spacer Screw STEPS 8-16 Back Tube (STEP 10) Plug Button Heavy (STEP 8) Pivot Arm Assembly Washer 2-inch Mounting (STEPS 8,9,12,13) (STEP 15) Screw (STE

Résumé du contenu de la page N° 6

PARTS LIST ITEM DESCRIPTION QTY 1 Pivot Arm Assembly 2 2 Plug Button 2 3 Strap and Stud Assembly 2 4 Locknut 2 5 5/16-24x2-inch Mntg Screw 2 6 Tube Clamp 2 7 Bushing 2 8 Thin Washer 2 9 Locknut 2 10 Pivot Arm Spacer 2 11 Wheel Lock Assembly 2 12 Axle Locknut 2 13 3/4-inch Mntg Screw 2 14 Washer (Heavy) 2 15 Axle Mounting Screw 2 1 2 5 14 12 13 11 6 7 3 8 9 10 15 4 6

Résumé du contenu de la page N° 7

NOTES 7

Résumé du contenu de la page N° 8

INVACARE CORPORATION l ONE INVACARE WAY l P.O. Box 4028 l Elyria, Ohio 44036-2125 l Phone 1-(800)-333-6900 Form No. 94-170 Part No. 1052754 Rev. (1) - 3/98 Printed in U.S.A.