Résumé du contenu de la page N° 1
M E M O R A N D U M
To: Jim Prescott
From: kent
Subject: Manual 90846
Date: August 29, 1997
cc:
Printing you purchasing copy for you. The last page will be the back cover, let me know if you re-
ceive the complete manual.
Résumé du contenu de la page N° 2
SPIRAL ICEMAKER-DISPENSER MODEL: SID650A/80 SID650W/80 SID650A/80--BC Operator ’ s Manual SID650W/80--BC Part No. 90846 August 1997 Revision F THIS DOCUMENT CONTAINS IMPORTANT INFORMATION This Manual must be read and understood before installing or operating this equipment PRINTED IN U.S.A â REMCOR INC: 1995
Résumé du contenu de la page N° 3
TABLE OF CONTENTS Page SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 UNPACKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Résumé du contenu de la page N° 4
TABLE OF CONTENTS (cont’ d) Page LIST OF FIGURES FIGURE 1. REAR VIEW - BOTTOM SECTION SERVICE PANEL REMOVED . 4 FIGURE 2. MOUNTING TEMPLATE MODEL SID650/80 . . . . . . . . . . . . . . . . . . . . 5 FIGURE 3. MOUNTING TEMPLATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 FIGURE 4. “B”MODELS POST MIX BEVERAGE SYUSTEM SCHEMATIC . . . 7 FIGURE 5. “BC”MODELS POST MIX BEVERAGE SYSTEM SCHEMATIC . . . 8 FIGURE 6. WIRING SCHEMATIC 115 / 1 / 60 HZ . . . . . . . . . . . . . .
Résumé du contenu de la page N° 5
SAFETY PRECAUTIONS Always disconnect power to the dispenser before servicing or cleaning. Never place hands inside of hopper or gate area without disconnecting power to the dispenser. Agitator rotation occurs automatically when the dispenser is energized! This ice dispenser has been specifically designed to provide protection against personal injury and eliminates contamination of ice. To insure continued protection and sanitation, observe the following ALWAYS be sure the removable lid is proper
Résumé du contenu de la page N° 6
DESCRIPTION The REMCOR LOW PROFILE S.I.D. (Spiral Iceâ Icemaker Dispenser) is a unique, self-contained, free stand- ing style unit which automatically makes hard, clear cube-quality ice and stores it in a sealed hopper for sanitary dispensing. The ice is made by a new, patented process on a spiral shaped stainless steel evaporator and pro- duces tube cube quality ice on the outside of the tubes. There are no augers, no compressing of flaked ice, no bearings and no high gear motor loads in the ic
Résumé du contenu de la page N° 7
INSTALLATION WARNING: Only qualified personnel should service internal components or electrical wiring. LOCATION Locate the icemaker/dispenser indoors in a well ventilated area. Avoid exposure to direct sunlight and/or heat caused by radiation. Ambient room temperature must be in the range of 60° to 90° F. Do not install unit in an enclosed area where heat build-up could be a problem. For proper air flow for the refrigeration system, allow 6” clearance at the back of the unit and a 12”clearance
Résumé du contenu de la page N° 8
BLACK (HOT) WHITE (NEUTRAL) SUPPLY CONDUIT GREEN (GROUND) 115V 60 HZ, 1PHASE FIGURE 1. REAR VIEW - BOTTOM SECTION SERVICE PANEL REMOVED BEVERAGE SYSTEM “B”, Models: contain beverage faucets only and must be supplied with cold product from any remote cold plate or refrigerated soda factory. “BC”units have a built-in cold plate, in addition to the beverage faucets and are de- signed to be supplied direct from syrup tanks and carbonator with no additional cooling required. Installation NOTE: This w
Résumé du contenu de la page N° 9
15 7/8 1 5/8 14 1 29/32 1 5/8 5/8 2 9/16 29 1/4 26 18 3/4 22 SHADED AREA INDICATES OPENING IN CABINET BOTTOM FOR BEVERAGE TUBING FOR --B, --BC MODELS ONLY FIGURE 2. MOUNTING TEMPLATE MODEL SID650--80 5 90846
Résumé du contenu de la page N° 10
90846 6 CLEARANCE NECESSARY ONLY IF UNIT IS INSTALLED IN AN ENCLOSED SPACE. 6 28 3/4 12 16 1/4 22 12 14 7/8 AIR AIR FLOW FLOW DOOR WITH LOCK 29 FOR ACCESS TO ICE STORAGE 15 3/4 49 2 1/2 12 AREA R ICE 12 11 1/8 17 5/8 9 AIR DISCHARGE GRILL 3 1/2 CONDENSER WATER IN 3/8 npt (WATER COOLED) 6 7/8 CONDENSER WATER OUT 34 3/8 29 1/4 3/8 npt (WATER COOLED) 34 7/8 ICEMAKER WATER IN 1/4 O.D. TUBE COMP. FITTING ELECTRICAL INPUT 16 5/8 ACCESS PANEL FOR SERVICE AND BEVERAGE HOOK-UP 3/4 FPT DRAINS (2) 13/16 6
Résumé du contenu de la page N° 11
90846 7 FIGURE 4. “B” MODELS POST MIX BEVERAGE SYUSTEM SCHEMATIC
Résumé du contenu de la page N° 12
90846 8 FIGURE 5. “BC” MODELS POST MIX BEVERAGE SYSTEM SCHEMATIC
Résumé du contenu de la page N° 13
START UP ICEMAKER 1. Open the hinged service door on the upper left side panel. Remove ice drop cover and storage hopper cov- er. 2. Turn on water to icemaker. Make sure that the proper water level is attained in the float chamber before starting unit. 3. Depress the flush switch for 30 seconds to verify that water dump valve operates and that the water drain lines are open and not plugged. 4. Put the “stop/run”switch in the “run”position. Observe that the icemaker goes through proper icemaking
Résumé du contenu de la page N° 14
OPERATING INSTRUCTIONS ICEMAKER OPERATING INSTRUCTIONS A temperature sensing bulb located in the storage hopper starts and stops the icemaking process (compressor) in response to the ice level in the hopper. With this ice level control “calling”for ice (hopper ice level is low), the total cycle timer energized. This timer , in turn energizes the harvest and agitation timers for their respective “on”times. The chart below details this sequence of events: HARVEST CYCLE Cam Time Switch Action 0 --
Résumé du contenu de la page N° 15
N COMPRESSOR TP R RUN CAP C CC S 5 2 START 1 RELAY START CAP STOP/ COMPRESSOR LPS BIN T’ STAT RUN HPS CONTACTOR CC 1 2 HARVEST MOTOR NC RED HT3 BLUE NO CAP CONDENSER FAN NC HT2 C RUN AIR PUMP NO CLEAN HG SOL VALVE NC HT4 C WATER DUMP VALVE NO FLUSH L N NC NO C HT ICE THICKNESS HT1 C HARVEST PROBE NC TIMER NO CONDUCTIVITY H CAP CONTROL COM AGITATOR MOTOR BLUE NO RED HT5 C F GATE SOLENOID VEND SWITCH NC MOTOR HEATER BEVERAGE TRANSFROMER (OPTIONAL) 24 V TO BEVERAGE FAUCETS FIGURE 6. WIRING SCHEMATI
Résumé du contenu de la page N° 16
FIGURE 7. WIRING DIAGRAM 12 90846
Résumé du contenu de la page N° 17
REFRIGERATION SCHEMATIC HOT GAS SOLENOID HIGH HIGH SIDE VALVE PRESSURE SERVICE CONTROL PORT AIR- -COOLED MODELS A CONDENSER COMPRESSOR LOW SIDE SERVICE PORT CONDENSER FAN LOW PRESSURE CONTROL B TXV SIGHT BULB GLASS FILTER/ DRIER EVAPORATOR TXV WATER- -COOLED MODELS PRESSURE TAP PRESSURE REGULATING VALVE CITY A WATER SUCTION ACCUMULATOR EXPANSION VALVE (TXV) DRAIN B COMPARTMENT FAN FIGURE 8. REFRIGERATION SCHEMATIC 13 90846
Résumé du contenu de la page N° 18
MAINTENANCE It is recommended that the air inlet filter be cleaned ever 3 months or sooner, depending on the operating envi- ronment for proper refrigeration system performance. On air-cooled units. also check that the condenser is free of dirt/foreign material that could cause air flow blockage. Consult the MAINTENANCE/ADJUSTMENT PROCE- DURES for cleaning these items. Cleaning of the icemaker is recommended on a regular basis not only for sanitary reasons but also to maintain the performance of
Résumé du contenu de la page N° 19
8. Open the water supply valve and fill evaporator with water (level is up in float reservoir). 9. Put the clean/run switch in the “clean”position. Allow unit to run in the cleaning mode for at least 30 min- utes. 10. Put the clean/run switch in the “run”position. 11. Close the water supply valve. 12. Depress the “Flush”switch push button and drain evaporator for about 1-1/2 minutes. Release push but- ton. Open the water supply valve. Allow evaporator to refill with water. Repeats Steps 11 and 1
Résumé du contenu de la page N° 20
2. Remove cold plate cover by loosening thumbscrew on the ice drop chute and lowering chute from plastic drop tube. then, remove cover by lifting slightly in front and slide forward. 3. Wash down the inside of the cold plate, tray and cover with mild detergent solution and rinse. A small, long- handled brush will be found helpful in reaching the corners. 4. Replace the cover, taking care that it is securely positioned in cold plate tray. 5. Replace ice drop chute. 6. Replace the lower front pane
