Résumé du contenu de la page N° 1
AC-6975TB-A
AC-6975TB-D
TOOLBOX
Toolbox Installation Instructions 1
Résumé du contenu de la page N° 2
Introduction Congratulations on the purchase of your new toolbox! You can be assured your toolbox was constructed and designed with quality and performance in mind. Each component has been rigorously tested to ensure the highest level of acceptance. This installation manual was compiled for your benefit. Please read and follow the simple installation instructions described in this manual. The contents of this manual are based on the latest product information available at the time of pu
Résumé du contenu de la page N° 3
Table of Content SAFETY .................................................................................................................4-5 GENERAL SAFETY RULES....................................................................4-5 FUNCTIONAL DESCRIPTION ...............................................................................6 MODEL ....................................................................................................6 NAME OF PARTS ...................................
Résumé du contenu de la page N° 4
Safety RECOGNIZE SAFETY INFORMATION This is the safety alert symbol. When you see this symbol in this manual, be alert to the potential for personal injury. Follow recommended precautions and safe operating prac- tices. UNDERSTAND SIGNAL WORDS A "DANGER, WARNING or CAUTION" safety warning will be surrounded by a "SAFETY ALERT BOX." This box is used to designate and emphasize Safety Warnings that must be fol- lowed when installing this toolbox. Accompanying the Safety Warnings are "signal
Résumé du contenu de la page N° 5
CAUTION THIS INSTALLATION REQUIRES THE USE OF POWER TOOLS. SAFETY GLASSES SHOULD BE WORN AT ALL TIMES DURING THE USE OF THE POWER TOOLS. IF YOU ARE UNABLE TO LIFT A MINIMUM OF 75 LBS., THEN THIS INSTALLATION WILL REQUIRE THE USE OF TWO PEOPLE. PINCH AREA BETWEEN BODY AND LID OF TOOLBOX. Toolbox Installation Instructions 5
Résumé du contenu de la page N° 6
Functional Description MODEL: AC-6975TB-A AC-6975TB-D NOTE: Some illustrations in this installation manual may show details that differ from those on your own toolbox. NAME OF PARTS: Single-Lid Toolbox: 3/8" J-Bolt (2) 3/8" Flatwasher (2) 3/8" Lockwasher (2) 3/8" Hex Nut (2) Vinyl Cap (2) Plastic Plug (2) Foam Tape (2) Toolbox Tray (1) TOOLS REQUIRED: 9/16" Wrench / Socket Drill with a 3/8" Drillbit Scissors Safety Glasses 6 Toolbox Installation Instructions
Résumé du contenu de la page N° 7
Installation INSTALLATION INSTRUCTIONS: CAUTION: THIS INSTALLATION REQUIRES THE USE OF POWER TOOLS. SAFETY GLASSES SHOULD BE WORN AT ALL TIMES DURING THE USE OF THE POWER TOOLS. CAUTION: IF YOU ARE UNABLE TO LIFT A MINIMUM OF 75 LBS., THEN THIS INSTALLATION WILL REQUIRE THE USE OF TWO PEOPLE. CAUTION: PINCH AREA BETWEEN BODY AND LID OF TOOLBOX. (FIG. 1) 1. Peel backing off the foam gasket (H). (Fig. 2) 2. Attach the foam gasket (H) onto the bottom of the to
Résumé du contenu de la page N° 8
Installation INSTALLATION INSTRUCTIONS (CONTINUED): CAUTION: SAFETY GLASSES SHOULD BE WORN DURING THIS STEP OF THE INSTALLATION. 4. Using Figures 5 and 6, mark the mounting hole locations for the J-hooks. The mounting hole locations should be centered inside the toolbox (A) and near the lip of the truck bed rail as shown below. (Fig.5) (Fig. 6) 8 Toolbox Installation Instructions
Résumé du contenu de la page N° 9
Installation INSTALLATION INSTRUCTIONS (CONTINUED): 5. Secure the toolbox (A) to the vehicle truck bed using the 3/8" J-bolts (B), 3/8" flatwasher (C), 3/8" lockwashers (D) , and the 3/8" hex nuts (E). Tighten into place using a 9/16" wrench / socket. (Fig. 7) 6. Now place the vinyl cap (F) onto the exposed threads of the 3/8" J-bolts (B). (Fig. 8) NOTE: After drilling, it is recommended that a sealant or rust inhibitor be placed around all holes drilled into the body panel
Résumé du contenu de la page N° 10
Maintenance MAINTENANCE INSTRUCTIONS: CLEANING INSTRUCTIONS: To maintain the luster of your toolbox, use a mild detergent. NOTE: Locks are provided as a deterrent to inadvertent opening or easy access to the contents of your toolbox. Contents stored in the toolbox are the responsibility of the user. LUBRICATION INSTRUCTIONS: All locks, latches, latching rods, and hinges should be lubricated regularly to assure smooth and proper operation for the life of the toolbox. Lubricate the fo
Résumé du contenu de la page N° 11
Notes Toolbox Installation Instructions 11
Résumé du contenu de la page N° 12
Form #37-0804-112003 Manufactured for Deere & Company 12 Toolbox Installation Instructions ©Copyright 2003, John Deere Moline, Illinois 61265 John Deere Toolbox
