Résumé du contenu de la page N° 1
OPTIONAL ACCESSORIES
22222
11111
SHREDDER KIT
R
P/N 890209. Shreds
leaves, dramatically reducing
total volume.
HOSE KITS
For vacuuming in hard to
reach areas.
Heavy Duty Vacuum
Hose Kit P/N 900943.
4"(102mm) x 10' (3.05m)
Homeowners Vacuum
Hose Kit P/N 900942.
4"(102mm) x 10' (3.05m)
NOZZLE WEAR PLATES
P/N 890413.
(STD. ON KD510HS) Extends
nozzle life when used along
curbs and hard surfaces.
STANDARD TURF QUICK
DEBRIS BAG
P/N 890307. (STD. ON TKD)
For use in leaves and grass in non-
dusty cond
Résumé du contenu de la page N° 2
555 55 IN THE INTEREST OF SAFETY BEFORE STARTING ENGINE, READ AND UNDERSTAND THE “ENTIRE OPERATOR'S MANUAL & EN- GINE MANUAL.” THIS SYMBOL MEANS WARNING OR CAUTION. DEATH, PERSONAL INJURY AND/OR PROPERTY DAMAGE MAY OCCUR UNLESS INSTRUCTIONS ARE FOLLOWED CAREFULLY. WARNING: The Engine Exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. 21. DO NOT touch hot muffler, cylinder, or 13. DO NOT tamper with governor spr
Résumé du contenu de la page N° 3
9 GENERAL SAFETY For your safety and the safety of others, these directions should be followed: Do not operate this machine without first reading ·DO NOT operate during excessive vibration. owner's manual and engine manufacturer's manual. ·DO NOT remove bag until engine has been turned off and has Use of Ear Protection is recommended while come to a complete stop. operating this machine. ·DO NOT remove hose kit cap on nozzle until engine has been turned off and has come to a complete stop.
Résumé du contenu de la page N° 4
12 12 13 13 13 13 13 CONTROLS 12 12 12 LITERATURE ASSY P/N 890392 Throttle Owner's Literature Check- Control Manual list Check Owner's Manual 890394 STOP Briggs Check Literature SLOW engines have Literature KD / TKD KD / TKD a primer Accessories Accessories button 890409 carburetor rather than choke type carburetor. Honda - Place in fast position Check Warranty to start. Warranty FAST Card Card 400972 Check Start EU Declaration EU Declaration of Conformity & of Conformity position EU Distribut
Résumé du contenu de la page N° 5
" 16 16 16 16 16 Operation INTENDED USE: This machine is designed for vacuuming CHIPPING OPERATION 16.7 16.7 16.7 16.7 16.7 leaves, grass clippings and other types of organic litter and (TKD MODLES ONLY) for chipping brush, limbs, corn and sunflower stalks and palm fronds. Debris mixed with cans, bottles and small amounts of sand Wearing Eye Protection and Durable can be vacuumed; however, it is not this machine's primary Gloves is recommended while operating purpose. Vacuuming cans, bottles an
Résumé du contenu de la page N° 6
16 16 OPERATION continued 16 16 16 16. 16. 16. 16. 16.33333 DEBRIS BAG Debris bags are normal replaceable wear items. Note: Frequently empty debris to prevent bag overloading with more weight than you can lift. An optional bag and dust cover is available for use where debris will be vacuumed in dusty conditions (see Optional Accessories shown on page 1). DO NOT place bag on or near hot surface, such as engine. Run engine at 1/2 throttle for first 1/2 hour to condition new bag. Your
Résumé du contenu de la page N° 7
OPERATION continued 16 16 16 16 16 16.4 16.4 16.4 16.4 16.4 HANDLING & TRANSPORTING: TAMPER 16. 16. 16. 16. 16.12 12 12 12 12 Before turning machine off, use the Tamper to slowly push Using two people to lift machine is recommended. Lift holding the remaining pieces of wood through the chipper. This can handle and front of nozzle. Secure in place during transport. prevent any remaining wood from jamming in the chipper when machine is turned off. Do not leave tamper on the ground, store tampe
Résumé du contenu de la page N° 8
17 17 17 17 17 MAINTENANCE CHIPPER BLADE REMOVAL AND SHARPENING Use only a qualified mechanic for any adjustments, disassembly or Chipper blades are normal replaceable wear items. any kind of repair . DANGER DANGER KEEP KEEP HANDS and FEET HANDS and FEET A AW WA AY Y DANGER Chipper blade is sharp. Replace any damaged blade. WARNING: TO AVOID PERSONAL INJURY, ALWAYS TURN MACHINE OFF, MAKE SURE ALL MOVING Depending on the type and amount of wood being chipped, the PARTS COME TO A COMPLETE STOP
Résumé du contenu de la page N° 9
17 17 17 17 17 MAINTENANCE continued 17.1 17.1 IMPELLER REMOVAL continued 17.1 17.1 17.1 17.2 17.2 17.2 17.2 17.2 18. If chipper blade properly clears anvil surface, proceed to step . If Follow these hourly not, return to (step 14) and add or subtract shim washers as Maintenance Schedule maintenance intervals. needed to obtain a correct gap. Every Every 5 hrs Maintenance Operation 19. Reinstall engine and impeller onto housing in reverse order of Use or (Daily) removal. Engine (See Engine
Résumé du contenu de la page N° 10
18 18 18 18 18 PARTS DRAWING KD510H, KD510HS, KD510, KD510IC, TKD510IC, TKD510H R Part No. 890394 Page 10 of 12 Form No. F011398B
Résumé du contenu de la page N° 11
item KD510 QTY KD510IC QTY KD510H QTY KD510HS QTY TKD510IC QTY TKD510H QTY PARTS Description 19 Part No. Part No. Part No. Part No. Part No. Part No. no. LIST * Denotes 1 TURF QUICK DEBRIS BAG (service) 890305 1 890305 1 890305 1 890305 1 890307 1 890307 1 standard 2 THROTTLE 850270 1 850270 1 850270 1 850270 1 850270 1 850270 1 hardware 3 item that 4 NUT LOCK (1/4 - 20 ) *8160001 8 *8
Résumé du contenu de la page N° 12
( Continued from page 11 ) PARTS LIST CONTINUED 19 19 19 19 19 item KD510 QTY KD510IC QTY KD510H QTY KD510HS QTY TKD510IC QTY TKD510H QTY PARTS * Denotes Part No. Part No. Part No. Part No. Part No. Part No. no. LIST Description standard 78 BOLT CARRIAGE 5/16-18x3/4" - - - - - - 8024039 2 - - - - hardware 79 LINE PVC - - - - - - 900732 1 - - - - item that 80 may be 81 purchased 82 locally. 83 CON
