Instruction d'utilisation Desa VN2000BB

Instruction d'utilisation pour le dispositif Desa VN2000BB

Dispositif: Desa VN2000BB
Catégorie: Système de chauffage à gaz
Fabricant: Desa
Dimension: 0.4 MB
Date d'addition: 1/4/2014
Nombre des pages: 32
Imprimez l'instruction

Téléchargez

Comment utiliser?

Notre objectif consiste à vous assurer le plus rapide accès au contenu de l'instruction d'utilisation du dispositif Desa VN2000BB. En utilisant l'aperçu en ligne vous pouvez parcourir le sommaire et passer à la page où vous trouverez la résolution de votre problème avec Desa VN2000BB.

Pour votre confort

Si regarder l'instruction Desa VN2000BB directement sur la page n'est pas confortable pour vous, vous pouvez profiter de deux solutions possibles:

  • Exploration au mode de plein écran - pour analyser l'instruction d'une manière commode (sans l'avoir téléchargée sur votre ordinateur) vous pouvez utiliser le mode d'exploration en plein écran. Pour démarrer l'exploration de l'instruction Desa VN2000BB en plein écran, utilisez le bouton Plein écran.
  • Téléchargement sur l'ordinateur - vous pouvez aussi télécharger l'instruction Desa VN2000BB sur votre ordinateur et la sauvegarder dans vos ressources. Si vous n'avez pas envie de gaspiller votre espace disque, vous pouvez toujours télécharger cette instruction du ManualsBase dans l'avenir.
Desa VN2000BB Manuel d'utilisation - Online PDF
Advertisement
« Page 1 of 32 »
Advertisement
Version imprimée

Beaucoup de gens préfèrent de lire les documents dans la version imprimée et non pas sur l'écran. L'option d'impression de l'instruction est aussi prévue et vous pouvez en profiter en cliquant le lien ci-dessus - Imprimez l'instruction. Il n'est pas nécessaire d'imprimer toute l'instruction Desa VN2000BB - on peut choisir des pages. Economisez le papier.

Résumés

Vous trouverez ci-dessous les annonces des contenus qui se trouvent sur les pages suivantes de l'instruction de Desa VN2000BB. Si vous voulez parcourir rapidement le contenu des pages suivantes de l'instruction, vous pouvez en profiter.

Résumés du contenu
Résumé du contenu de la page N° 1

®
VENT-FREE NATURAL GAS HEATER
OWNER’S OPERATION AND INSTALLATION MANUAL
Model: VGN30B and VN2000BB
WARNING: If the information in this manual is not followed exactly, a fire or
explosion may result causing property damage, personal injury, or loss of life.
— Do not store or use gasoline or other flammable vapors and liquids in the
vicinity of this or any other appliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone

Résumé du contenu de la page N° 2

SECTION PAGE CONTENTS Safety Information ......................................................................... 2 Product Identification .................................................................... 4 Local Codes ................................................................................... 4 Unpacking...................................................................................... 4 Product Features ............................................................................

Résumé du contenu de la page N° 3

SAFETY WARNING ICON G 001 WARNINGS Continued INFORMATION WARNING: Any change to this heater or its controls can be dangerous. Continued 1. Use only natural gas. Do not convert heater to use different fuel type. 2. If you smell gas • Shut off gas supply • Do not try to light any appliance • Do not touch any electrical switch; do not use any phone in your building • Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions • If you cannot reach your gas sup

Résumé du contenu de la page N° 4

Ignitor Button Control Knob PRODUCT IDENTIFICATION Grill Guard Heat Shield (VGN30B) or Glass Panel (VN2000BB) Front Panel Heater Cabinet Figure 1 - Vent-Free Natural Gas Heater Install and use heater with care. Follow all local codes. In the absence of local LOCAL CODES codes, use the latest edition of National Fuel Gas Code ANSI Z223.1, also known as NFPA 54*. *Available from: American National Standards Institute, Inc. 1430 Broadway New York, NY 10018 National Fire Protection Association, Inc

Résumé du contenu de la page N° 5

FRESH AIR WARNING WARNING ICON G 001 FOR This heater must have fresh air for proper operation. If not, poor fuel combustion could result. Read the following instructions to COMBUSTION insure proper fresh air for this and other fuel-burning appliances in your home. AND VENTILATION Today’s homes are built more energy efficient than ever. New materials, increased insulation, and new construction methods help reduce heat loss in homes. Home owners weather strip and caulk around windows and doors to

Résumé du contenu de la page N° 6

DETERMINING FRESH-AIR FLOW FOR HEATER LOCATION FRESH AIR Determining if You Have a Confined or Unconfined Space FOR Use this worksheet to determine if you have a confined or unconfined space. COMBUSTION Space: Includes the room in which you will install heater plus any adjoining rooms with doorless passageways or ventilation grills between the rooms. AND 1. Determine the volume of the space (length x width x height). VENTILATION Length x Width x Height = ___________________ cu. ft. (volume of sp

Résumé du contenu de la page N° 7

VENTILATION AIR FRESH AIR Ventilation Air From Inside Building FOR This fresh air would come from an adjoining unconfined space. When ventilating to an adjoining unconfined space, you must provide two permanent openings: one within 12" of the COMBUSTION ceiling and one within 12" of the floor on the wall connecting the two spaces (see options 1 and AND 2, Figure 2). You can also remove door into adjoining room (see option 3, Figure 2). VENTILATION WARNING WARNING ICON G 001 Continued Rework wor

Résumé du contenu de la page N° 8

VENTILATION AIR (Continued) FRESH AIR Ventilation Air From Outdoors FOR Provide extra fresh air by using ventilation grills or ducts. You must provide two perma- nent openings: one within 12" of the ceiling and one within 12" of the floor. Connect these COMBUSTION items directly to the outdoors or spaces open to the outdoors. These spaces include attics AND and crawl spaces. Follow the National Fuel Gas Code NFPA 54/ANSI Z223.1, Section 5.3, Air for Combustion and Ventilation for required size o

Résumé du contenu de la page N° 9

INSTALLING NOTICE TO WALL A qualified service person must install heater. Follow all local codes. CHECK GAS TYPE Use only natural gas. If your gas supply is not natural gas, do not install heater. Call dealer where you bought heater for proper type heater. INSTALLATION ITEMS Before installing the heater, make sure you have the items listed below. • piping (check local codes) • test gauge connection * (see • sealant (resistant to propane gas) Figure 12, page 15) • manual shutoff valve * • sedimen

Résumé du contenu de la page N° 10

INSTALLING CAUTION WARNING ICON G 001 TO WALL If you install the heater in a home garage • heater pilot and burner must be at least 18 inches above floor Continued • locate heater where moving vehicle will not hit it For convenience and efficiency, install heater • where there is easy access for operation, inspection, and service • where strong wind gusts from an open door or garage door can not blow directly into heater. An optional fan kit is available from your dealer. See Accessories, p

Résumé du contenu de la page N° 11

INSTALLING HEATER TO WALL INSTALLING Mounting Bracket TO WALL The mounting bracket is located on back panel of heater. It has been taped there for Continued shipping. Remove mounting bracket from back panel. Mounting Bracket Figure 5 - Mounting Bracket Location Removing Front Panel Of Heater 1. Remove two screws near bottom corners of front panel. 2. Lift straight up on grill guard until it stops. Grill guard will slide up about 1/4". 3. Pull bottom of front panel forward, then down. 4. Remove c

Résumé du contenu de la page N° 12

Marking Screw Locations INSTALLING 1. Tape mounting bracket to wall where heater will be located. Make sure mount- TO WALL ing bracket is level. Continued WARNING WARNING ICON G 001 Maintain minimum clearances shown in Figure 7. If you can, provide greater clearances from floor and joining wall. 2. Mark screw locations on wall (see Figure 7). Note: Only mark last hole on each end of mounting bracket. Insert mounting screws through these holes only. 3. Remove tape and mounting bracket from wall.

Résumé du contenu de la page N° 13

4. For thin walls (1/2" or less), insert red key into wall anchor. Push red key to INSTALLING “pop” open anchor wings. IMPORTANT: Do not hammer key! For thick walls (over 1/2" thick) or solid walls, do not pop open wings. TO WALL Continued Figure 9 - Popping Open Anchor Wings For Thin Walls 5. Place mounting bracket onto wall. Line up last hole on each end of bracket with wall anchors. 6. Insert mounting screws through bracket and into wall anchors. 7. Tighten screws until mounting bracket is fi

Résumé du contenu de la page N° 14

CONNECTING NOTICE A qualified service person must connect heater to gas supply. TO GAS Follow all local codes. SUPPLY WARNING WARNING ICON G 001 Never connect heater to private (non-utility) gas wells. This gas is commonly known as well-head gas. IMPORTANT: Check gas line pressure before connecting heater to gas line. Gas line pressure must be no greater than 14 inches of water. If gas line pressure is higher, heater regulator damage could occur. CAUTION WARNING ICON G 001 Use only new, black

Résumé du contenu de la page N° 15

IMPORTANT: Hold pressure regulator with wrench when connecting it to gas piping CONNECTING and/or fittings. Note: Burner bracket TO GAS not shown for clarity Pressure SUPPLY Regulator Continued 1/2" NPT Pipe Nipple Heater Ground Joint Cabinet Union Tee Joint Test Reducer Manual Bushing to Gauge Shutoff 1/8" NPT Connection * Valve * From 1/8" NPT Gas Meter Plug Tap (4" W.C. to 10.5" W.C. Tee Joint Pressure) Sediment Pipe 3" Minimum Trap Nipple Cap Figure 12 - Gas Connection * An A.G.A. design c

Résumé du contenu de la page N° 16

4. Check all joints of gas supply piping system. Apply mixture of liquid soap and CHECKING water to gas joints. Bubbles forming show a leak. GAS 5. Correct all leaks at once. Test Pressures Equal To or Less Than 1/2 PSIG CONNECTIONS 1. Close manual shutoff valve (see Figure 13). Continued 2. Pressurize supply piping system by either using compressed air or opening main gas valve located on or near gas meter. 3. Check all joints from gas meter to manual shutoff valve (see Figure 14). Apply mixtur

Résumé du contenu de la page N° 17

OPERATING FOR YOUR SAFETY READ BEFORE LIGHTING HEATER WARNING ICON G 001 WARNING If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly. B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the f

Résumé du contenu de la page N° 18

4. Wait five (5) minutes to clear out any gas. Then smell for gas, including OPERATING near the floor. If you smell gas, STOP! Follow “B” in the safety information HEATER at the top of page 17. If you don’t smell gas, go to the next step. Continued C-clockwise 5. Press in control knob and turn counterclockwise to the PILOT position. Keep control knob pressed in for five (5) seconds (see Figure 15, page 17). Note: You may be running this heater for the first time after hooking up to gas supply.

Résumé du contenu de la page N° 19

OPERATING TO TURN OFF GAS TO APPLIANCE Shutting Off Heater HEATER 1. Turn control knob clockwise Clockwise to the PILOT position. Continued 2. Press in control knob and turn clockwise to the OFF position. Clockwise 3. Turn off all electric power to the appliance if service is to be performed. Shutting Off Burner Only (pilot stays lit) 1. Turn control knob clockwise Clockwise to the PILOT position. MANUAL LIGHTING PROCEDURE 1. Remove front panel (see Figure 6, page 11). 2. Follow steps 1 through

Résumé du contenu de la page N° 20

If pilot flame pattern is incorrect, as shown in Figure 18 INSPECTING • turn heater off (see To Turn Off Gas to Appliance, page 19) BURNER • see Troubleshooting, pages 21 through 24 Continued BURNER FLAME PATTERN Figure 19 shows a correct burner flame pattern. Figure 20 shows an incorrect burner flame pattern. The incorrect burner flame pattern shows yellow tipping of the flame. It also shows the flame higher than 1/2 the heat shield height. WARNING WARNING ICON G 001 If yellow tipping occu


Instructions pareilles
# Instruction d'utilisation Catégorie Téléchargez
1 Desa 125-R Manuel d'utilisation Système de chauffage à gaz 0
2 Desa BG30P Manuel d'utilisation Système de chauffage à gaz 0
3 Desa 30-80 Manuel d'utilisation Système de chauffage à gaz 0
4 Desa 75-200 Manuel d'utilisation Système de chauffage à gaz 0
5 Desa BG30N Manuel d'utilisation Système de chauffage à gaz 0
6 Desa BG30NT Manuel d'utilisation Système de chauffage à gaz 0
7 Desa BCLP375 Manuel d'utilisation Système de chauffage à gaz 0
8 Desa BG30PT Manuel d'utilisation Système de chauffage à gaz 0
9 Desa 125-RN Manuel d'utilisation Système de chauffage à gaz 0
10 Desa BLP35E Manuel d'utilisation Système de chauffage à gaz 0
11 Desa BVDR18 Manuel d'utilisation Système de chauffage à gaz 1
12 Desa BVDR24 Manuel d'utilisation Système de chauffage à gaz 0
13 Desa BVDR30 Manuel d'utilisation Système de chauffage à gaz 0
14 Desa BVSR18 Manuel d'utilisation Système de chauffage à gaz 0
15 Desa CB36N Manuel d'utilisation Système de chauffage à gaz 0
16 Allied Air Enterprises 506271-01 Manuel d'utilisation Système de chauffage à gaz 0
17 Blue Rhino ALL WEATHER WOVEN HEATER GWU9850F / 35554 Manuel d'utilisation Système de chauffage à gaz 2
18 Breckwell ECONOMY P22FSL Manuel d'utilisation Système de chauffage à gaz 0
19 Breckwell ECONOMY P22FSA Manuel d'utilisation Système de chauffage à gaz 0
20 Breckwell ECONOMY P22I Manuel d'utilisation Système de chauffage à gaz 1