Résumé du contenu de la page N° 1
COIL ROOFING NAILER
Model 68024
SET UP AND OPERATING INSTRUCTIONS
Visit our website at: http://www.harborfreight.com
Read and understand tool labels and
manual. Failure to follow warnings could
result in DEATH or SERIOUS INJURY.
SAVE THIS MANUAL.
© ®
Copyright 2010 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within thi
Résumé du contenu de la page N° 2
CAUTION, without the SAVE THIS MANUAL safety alert symbol, is Keep this manual for the safety warnings used to address practices not and precautions, assembly, operating, related to personal injury. inspection, maintenance and cleaning procedures. Write the product’s serial number Symbol Definitions in the back of the manual near the assembly diagram (or month and year of purchase if Symbol Property or statement product has no number). Keep this manual Pounds per square inch of pres
Résumé du contenu de la page N° 3
WARNING – When using tools, basic c. Avoid unintentional starting. Be precautions should always be followed, sure the trigger is released before including the following: connecting to the air supply. Do not carry the tool with your finger on the trigger or connect the tool to the air General supply with the trigger pressed. a. To reduce the risks of electric shock, d. Do not overreach. Keep proper fire, and injury to persons, read all the footing and balance at all times. instructions b
Résumé du contenu de la page N° 4
specific tool model, increases the risk of Tool use and care injury to persons. a. Use clamps or another practical way i. Use only those fasteners listed in the to secure and support the workpiece Specifications chart of this manual. to a stable platform. Holding the work Fasteners not identified for use with this by hand or against the body is unstable tool by the tool manufacturer are able to and can lead to loss of control. result in a risk of injury to persons or tool b. Do not fo
Résumé du contenu de la page N° 5
d. Moving the tool to a new location. Specific Safety Instructions SPECIFIC INSTRUCTIONS 13. Do not make any modifications to tool. 1. Operators and others in work area 14. Refer to the tool maintenance instructions for detailed information on MUST wear ANSI‑approved safety goggles with side shields during use. the proper maintenance of the tool. The employer is responsible to enforce 15. Fire fasteners into an appropriate the use of eye protection by the operator work surface only. Do n
Résumé du contenu de la page N° 6
24. Do not engrave or stamp anything into 1. Anyone using vibrating tools regularly the housing to avoid weakening it. or for an extended period should first be examined by a doctor and then have 25. WARNING: Some dust created by regular medical check-ups to ensure power sanding, sawing, grinding, medical problems are not being caused drilling, and other construction activities, or worsened from use. Pregnant contains chemicals known [to the State women or people who have impaired o
Résumé du contenu de la page N° 7
FUNCTIONAL DESCRIPTION INITIALASSEMBLY Functional Description Initial Tool Setup/Assembly Specifications Read the ENTIRE IMPORTANT SAFETY INFORMATION Max. Air Pressure 120 PSI section at the beginning of this Air Inlet 1/4” -18 NPT manual including all text under Air Consumption 1 CFM @ 90 PSI subheadings therein before set up Fastener 11 Gauge, 3/4” to 1-3/4” Wire- or use of this product. Capacity Collated Roofing Nails Magazine Note: For additional information regarding the 120 Capa
Résumé du contenu de la page N° 8
Air Tool & Spray Gun Portable Setup Page 8 For technical questions, please call 1800 ‑ ‑444‑3353. SKU 68024 C Lubricated B D A E F Tools A Non-lubricated E H C Tools B G A Description Function A Air Hose Connects air to tool B Filter Prevents dirt and condensation from damaging tool or work piece C Regulator Adjusts air pressure to tool D Lubricator (optional) For air tool lubrication E Coupler and Plug Provides each connections F Leader Hose (optional) Increases coupler life G Air C
Résumé du contenu de la page N° 9
Air Tool & Spray Gun Stationary Setup SKU 68024 For technical questions, please call 1‑800‑444‑3353. Page 9 Slope Lubricated Tools J G C K F L M O C D E H M N C J B B F A A H I F L Non-lubricated Tools Description Function A Vibration Pads For noise and vibration reduction B Anchor Bolts Secures air compressor in place C Ball Valve Isolates sections of system for maintenance D Isolation Hose For vibration reduction E Main Air Line - 3/4” minimum recommended Distributes air to bra
Résumé du contenu de la page N° 10
air hose is ruptured. The shutoff the air output gauge to set the right valve should be a ball valve because pressure range. it can be closed quickly. See pages 8 8. The air pressure setting must not exceed and 9 for Air Tool Setup procedures. job site regulations/restrictions. The air Note: If an automatic oiler system is not pressure setting must not exceed 90 PSI used, add a few drops of Pneumatic when being used with work pieces that Tool Oil into the airline connection before have a
Résumé du contenu de la page N° 11
The tool should only fire if the Safety OPERATING INSTRUCTIONS Operating Instructions Nosepiece is pressed against the workpiece and the trigger is pulled. It should fire again Read the ENTIRE IMPORTANT if the trigger is released and pulled OR SAFETY INFORMATION if the safety is lifted and pressed against section at the beginning of this the workpiece again. The Tool should not manual including all text under fire if the Safety Nosepiece is not pressed subheadings therein before set
Résumé du contenu de la page N° 12
stop immediately and take the tool to a 3. Check that the Trigger and the Safety qualified service technician. Nosepiece move freely, without sticking. 7. Press the Safety Nosepiece against 4. Connect the air supply to the tool and the workpiece and squeeze the Trigger. set within the Operating Air Pressure The tool must cycle (fire) only once. indicated on the Specification chart. Release the trigger and squeeze it 5. Test the tool by pressing the Safety again. The tool must cycle (fire)
Résumé du contenu de la page N° 13
5. Swing the Magazine Cover closed. Loading the Tool Then, close the Cover Plate, making TO PREVENT sure the Latch snaps shut. If the Latch SERIOUS INJURY does not engage, the nail head is not in FROM ACCIDENTAL OPERATION, the slot in the upper portion of the Feed BEFORE LOADING: Drive Guide. • Wear ANSI‑approved safety goggles with side shields. Other Roofing Gauge Adjustment people in the work area must also 1. The Roofing Gauge (82) controls roof wear ANSI-approved impact safe
Résumé du contenu de la page N° 14
5. If the tool requires more force to accomplish the task, verify that the tool receives sufficient, unobstructed airflow (CFM) and increase the pressure (PSI) output of the regulator up to the maximum air pressure rating of this tool. CAUTION! TO PREVENT TOOL AND ACCESSORY FAILURE, RESULTING IN INJURY: Do not exceed the tool’s maximum air pressure rating. If the tool still does not have sufficient force at maximum pressure and sufficient airflow, then a larger tool may
Résumé du contenu de la page N° 15
mechanism and may be highly USERINSTRUCTIONS ‑ User‑Maintenance Instructions flammable, causing an explosion. Note: These procedures are in addition to Procedures not specifically the regular checks and maintenance explained in this manual must explained as part of the regular operation be performed only by a qualified of the air-operated tool. technician. Daily ‑ Air Supply Maintenance: TO PREVENT Every day, perform maintenance on the SERIOUS INJURY air supply according to the
Résumé du contenu de la page N° 16
2. Remove the jammed fasteners with pliers. 3. If a fastener is jammed in the Magazine, lift open the Latch, and then swing back the moveable Cover Plate and then the Magazine Cover. 4. Uncoil the fasteners and, if necessary, use a screwdriver to release the jammed fastener. 5. Pull out the jammed fastener. 6. If you are unable to clear the fastener jam using the method prescribed above, the tool should be taken to a qualified service technician for proper servicing. Record Product’s
Résumé du contenu de la page N° 17
Troubleshooting Problem Possible Causes Likely Solutions Insufficient 1. Incorrect tool depth setting. 1. Adjust depth setting. fastener depth. 2. Not enough air pressure. 2. Check for loose connections and make sure that air supply is providing enough air pressure (PSI) to the tool’s air inlet. Do not exceed 120 PSI maximum air pressure. 3. Incorrect lubrication or not 3. Lubricate using air tool oil and grease according to enough lubrication. directions. 4. Blocked air inlet screen 4.
Résumé du contenu de la page N° 18
Parts List Part Description Q’ty Part Description Q’ty 1 Hex bolt M5x10 1 52 Depth Knob 1 Flat Washer 6 2 2 Retaining Ring 3 1 53 3 Air deflector 1 Air valve seat sealing ring 1 54 Deflector cover 1 4 55 O-ring 16x1.6 1 Cylinder cap sleeve 1 5 Sleeve seat 1 56 6 Hex bolt M5x25 4 O-ring 6.1x1.8 1 57 Spring Washer 5 4 7 58 O-ring 6.4x2 1 Hex flat end bolt M5x8 1 8 Valve sleeve 1 59 9 Cylinder cap 1 O-ring 9x1.8 1 60 Cylinder cap O-ring 17x1.8 1 10 61 O-ring 2.5x1.5 2 Cylinder cap bumper 1 11 Air
Résumé du contenu de la page N° 19
Assembly Diagram SKU 68024 For technical questions, please call 1‑800‑444‑3353. Page 19
Résumé du contenu de la page N° 20
Limited 1Y ‑ ear Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of one year from the date of purchase (90 days if used by a professional contractor or if used as rental equipment). This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repa
