Résumé du contenu de la page N° 1
650CRT
Owner's Manual
Résumé du contenu de la page N° 2
SAFETY RULES SAFE OPERATION PRACTICES FOR WALK-BEHIND POWERED ROTA R Y TILLERS Keep children and pets away. TRAINING Do not overload the machine capacity by attempting Read the Owner’s Manual care ful ly. Be thor ough ly to till too deep at too fast a rate. fa mil iar with the controls and the proper use of the equip ment. Know how to stop the unit and disengage Never operate the machine at high speeds on slippery the controls quickly. surfaces. Look behind and use care
Résumé du contenu de la page N° 3
CUSTOMER RESPONSIBILITIES PRODUCT SPECIFICATIONS Read and observe the safety rules. Gasoline Capacity: 3 Quarts Follow a regular schedule in maintaining, caring for Unleaded Reg u lar and using your tiller. OIL (API-SF/SJ): SAE 30 (Above 40°F) Follow instructions under “Maintenance” and “Stor age” (Capacity 20 oz./0.6L) SAE 5W-30/10W30 sections of this Owner’s Manual. (Below 40°F) IMPORTANT: THIS UNIT IS EQUIPPED WITH AN INTERNAL Spark Plug: Champion COMBUSTION E
Résumé du contenu de la page N° 4
ASSEMBLY Your new tiller has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tiller all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. TOOLS REQUIRED FOR ASSEMBLY FRONT A socket wrench set will make assembly easier. Standard wrench sizes are listed. (1) Utility knife (1) Tire pressure gauge (1) Pair of pliers LEFT RIGHT
Résumé du contenu de la page N° 5
ASSEMBLY UNPACKING CARTON (See Fig. 2) Grasp handle assembly. Hold in “up” position. Be sure handle lock remains in gearcase notch. Slide handle assembly into position. CAUTION: Be careful of exposed sta ples when handling or disposing of cartoning material. HANDLE ASSEMBLY "UP" POSITION IMPORTANT: WHEN UN PACK ING AND AS SEM BLING TILLER, BE CAREFUL NOT TO STRETCH OR KINK CABLES. TIGHTEN HANDLE LOCK LEVER TO HOLD While holding handle assembly, cut cable ties se cur ing han
Résumé du contenu de la page N° 6
ASSEMBLY ATTACH CLUTCH CABLE (See Fig. 6) CONNECT SHIFT ROD (See Fig. 7) Insert end of shift rod into hole of shift lever indicator. Hook end of clutch cable through hole in control bar bracket. Insert hairpin clip through hole of shift rod to secure. SHIFT HAIRPIN CONTROL BAR SHIFT LEVER CLIP BRACKET ROD INDICATOR CONTROL BAR CLUTCH CABLE CONTROL BAR FIG. 7 BRACKET REMOVE TILLER FROM CRATE Make sure shift lever indicator is in “N” position (See Fig. 7) END OF CLUTCH
Résumé du contenu de la page N° 7
OPERATION KNOW YOUR TILLER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TILLER. Compare the illustrations with your tiller to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your Tiller or in literature supplied with the product. Learn and understand their meaning. THROTTLE CONTROL SHIFT LEVER CHOKE CONTROL SHIFT LEVER IN DI CATO R DRIVE CONTROL BAR DEPTH STAKE LEVELING SHIELD RE
Résumé du contenu de la page N° 8
OPERATION The operation of any tiller can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields before starting your tiller and while tilling. We recommend a wide vision safety mask for over spectacles or standard safety glasses. DEPTH STAKE (See Fig. 10) HOW TO USE YOUR TILLER The depth stake can be raised or lowered to allow you more Know how to operate all controls before adding fuel and versatile tilling and cul
Résumé du contenu de la page N° 9
OPERATION For cold weather operation you should change oil for TURNING easier starting (See oil viscosity chart in the Mainte- Release the drive control bar. nance sec tion of this manual). Move throttle control to “SLOW” position. To change engine oil, see the Maintenance section in Place shift lever indicator in “F” (forward) position. Tines this manual. will not turn. Lift handle to raise tines out of ground. Swing the handle in the opposite direction y
Résumé du contenu de la page N° 10
OPERATION Move choke control to choke position. Soil conditions are important for proper tilling. Tines will not readily penetrate dry, hard soil which may con tribute Grasp recoil starter handle with one hand and grasp to excessive bounce and diffi cult handling of your tiller. tiller handle with other hand. Pull rope out slowly until Hard soil should be mois tened before tilling; however, engine reaches start of com pres sion cycle (rope will extremely wet soil will “bal
Résumé du contenu de la page N° 11
MAINTENANCE MAINTENANCE SCHEDULE FILL IN DATES AS YOU COMPLETE SERVICE DATES REGULAR SERVICE Check Engine Oil Level Change Engine Oil 1,2 Oil Pivot Points Inspect Spark Arrester / Muffler Inspect Air Screen Clean or Replace Air Cleaner Cartridge 2 Clean Engine Cylinder Fins Replace Spark Plug RH Gear Case Grease Fitting (1oz.) 1 - Change more often when operating under a heavy load or in high ambient temperatures. 2 - Service more often when operating in dirty or dusty conditions. LUBRICATION C
Résumé du contenu de la page N° 12
MAINTENANCE Disconnect spark plug wire before performing any maintenance (except car bu re tor adjustment) to prevent accidental start ing of engine. Prevent fi res! Keep the engine free of grass, leaves, spilled oil, or fuel. Re move fuel from tank before tipping unit for maintenance. Clean muffl er area of all grass, dirt, and debris. Do not touch hot muffl er or cylinder fi ns as contact may cause burns. ENGINE LUBRICATION Use only high quality detergent oil rated with API service classifi
Résumé du contenu de la page N° 13
MAINTENANCE MUFFLER COVER KNOB Do not operate tiller without muffl er. Do not tamper with exhaust system. Damaged muffl ers or spark arresters could COVER create a fi re hazard. Inspect pe ri odi cally and re place if nec es sary. If your engine is equipped with a spark arrester FOAM screen assembly, re move every 50 hours for cleaning and PRECLEANER inspection. Re place if dam aged. AIR CLEANER CARTRIDGE SPARK PLUG Replace spark plugs at the beginning of each tilling sea- BASE son or after
Résumé du contenu de la page N° 14
SERVICE AND ADJUSTMENTS CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come into contact with plug. TILLER CLEVIS PIN TO ADJUST HANDLE HEIGHT (See Fig. 20) Select handle height best suited for your tilling conditions. Handle height will be different when tiller digs into soil. NUT “C” First loosen handle lock lever. Handle can be positioned at different settings between NUT “HIGH” and “LOW” positions. “D” Retighten handle lock lever secu
Résumé du contenu de la page N° 15
SERVICE AND ADJUSTMENTS GROUND DRIVE BELT ADJUSTMENT (See TO REPLACE GROUND DRIVE BELT (See Fig. 23) Fig. 23) For proper belt tension, the extension spring should Remove belt guard (See “TO REMOVE BELT GUARD” in this section of this manual). have about 5/8 inch stretch when drive control bar is in “EN GAGED” position. This tension can be attained as Remove old belt by slipping off engine pulley fi rst then follows: remove from transmission pulley. Loosen cable clip screw s
Résumé du contenu de la page N° 16
SERVICE AND ADJUSTMENTS To maintain the superb tilling performance of this TINE REPLACEMENT (See Figs. 24, 25, and ma chine the tines should be checked for sharpness, 26) wear, and bending, particularly the tines which are next to the transmission. If the gap between the tines CAUTION: Tines are sharp. Wear ex ceeds 3-1/2 inches (9 cm), they should be replaced gloves or other protection when han- or straight ened as necessary. dling tines. New tines should be assembled as s
Résumé du contenu de la page N° 17
SERVICE AND ADJUSTMENTS ENGINE TO ADJUST CARB URETOR The carburetor has been preset at the factory and ad just ment TO ADJUST THROTTLE CONTROL CABLE should not be necessary. However, engine per formance (See Fig. 27) can be affected by dif ferenc es in fuel, tem per a ture, al ti tude or load. If the carburetor does need ad just ment, contact The throttle control has been preset at the factory and your nearest authorized service center/de part ment ad just ment should not be necessary
Résumé du contenu de la page N° 18
STORAGE Immediately prepare your tiller for storage at the end of the ENGINE OIL season or if the unit will not be used for 30 days or more. Drain oil (with engine warm) and replace with clean oil. (See “ENGINE” in the Maintenance section of this man ual). CAUTION: Never store the tiller with gasoline in the tank inside a build ing CYLINDER(S) where fumes may reach an open fl ame Remove spark plug. or spark. Allow the engine to cool before Pour 1 ounce (29 ml) of oil through sp
Résumé du contenu de la page N° 19
TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION Will not star t 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly. 2. See “TO START ENGINE” in Operation section. 3. Engine fl ooded.
Résumé du contenu de la page N° 20
REPAIR PARTS TILLER - - MODEL NUMBER 650CRTC, PRODUCT NUMBER 954 32 80-30 HANDLE ASSEMBLY KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 532 18 06-34 Control, Throttle 21 532 18 11-27 Handle 2 532 00 92-66 Grip, Handle 23 532 08 67-77 Screw, Hex Washer Hd. Slotted 4 532 15 92-28 Bar Assembly, Control #10-24 x 1/2 6 532 18 06-76 Panel, Control 24 5
