Instruction d'utilisation Life Fitness Seated Row

Résumé du contenu de la page N° 1

Seated Row
Assembly Instructions

Résumé du contenu de la page N° 2

Seated Row Assembly Instructions Item Qty Description Part Number Item Qty Description Part Number 1 1 Pulley 3237801 22 1 Output Cam 7998501 2 2 Pulley Guard 79794XX 23 1 Output Plate 7998495 3 1 Tower Support 80385XX 24 1 Output Ring 7998895 4 9 M10 x 45mm Bolt 3251706 25 1 Rear Shroud 8024807 5 41 3/8” Flat Washer 3102514 26 1 Front Shroud 8024707 6 1 Bottom Brace 80004XX 27 4 M10 x 20mm Bolt 3251701 7 1 Center Frame 80187XX 28 1 Plate 7322301 8 1 Tower 79854XX 29 1 Seat Pad 74689XX 9 4 M10 x

Résumé du contenu de la page N° 3

Résumé du contenu de la page N° 4

Seated Row Assembly Instructions 1. Assemble the PULLEY (1) and two PULLEY GUARDS (2) to the TOWER SUPPORT (3) using one M10 X 45mm BOLTS (4) and one 3/8" SAE WASHER (5) as shown. Tighten the BOLT securely. 2. LOOSELY assemble the BOTTOM BRACE (6) and CENTER FRAME (7) to the TOWER (8) using four M10 X 130mm BOLTS (9), eight 3/8" SAE WASHERS (5) and four M10 NYLOCK NUTS (10) as shown. 3. LOOSELY assemble the SEAT FRAME (11) to the BOTTOM BRACE (6) and CENTER FRAME (7) using four M10 X 90mm BOLTS

Résumé du contenu de la page N° 5

8. Assemble the OUTPUT CAM (22), OUTPUT PLATE (23), and OUTPUT RING (24) using three M10 X 45mm BOLTS (4) and three 3/8" SAE WASHERS (5) as shown. Tighten the BOLTS securely. 9. Assemble the REAR SHROUD (25) and FRONT SHROUD (26) to the TOWER (8) using four M10 X 20mm BOLTS (27), four 3/8" SAE WASH- ERS (5) as shown. Be sure all tabs along the sides and top of the SHROUDS are fully engaged in the slots located inside the TOWER. Tighten the BOLTS securely. Do not overtighten the BOLTS. 10. Secure

Résumé du contenu de la page N° 6

Seated Row Assembly Instructions 11. Attach the SEAT PAD (29) to the SEAT FRAME (11) using two M10 X 35mm BOLTS (30) and two 3/8" SAE WASHERS (5) as shown. Tighten the BOLT securely.

Résumé du contenu de la page N° 7

NOTE: Some components have been removed from the illustration for clarity. 12. Assemble one M10 HEX JAM NUT (31) onto one end of the CABLE (32) approximately 1/2”. Assemble the ROD END BEARING (33) to the same end of the CABLE until it meets the M10 HEX JAM NUT. Tighten the M10 HEX JAM NUT securely. 13. Loosely assemble the ROD END BEARING (33) of the CABLE (32) to the WORKARM (15) using one M10 X 40mm BOLT (34), SPACER (35), 3/8" SAE WASHER (5) and M10 NYLOCK NUT (10). 14. Route the CABLE (32)

Résumé du contenu de la page N° 8

Seated Row Assembly Instructions © 2006 Life Fitness, a division of Brunswick Corporation. All rights reserved. Life Fitness is a registered trademark of Brunswick Corporation. TCRW 6.09.06 8060801 RevA-2