Instruction d'utilisation Sears S A - 4 0 0 B H

Résumé du contenu de la page N° 1

OWNER'S MANUAL
40" LAWN AERATO R
MODEL:
SA-400BH
• Assembly
• Installation
• Operation
• Repair Parts
Original Instructions
For the latest product updates & setup tips:
Important: This manual contains information for the safety
Visit us on the web!
of persons and property. Read it carefully before
www.brinly.com
assembly and operation of the equipment!
1008590BH-C

Résumé du contenu de la page N° 2

INTRODUCTION AND SAFETY ================================================================================================ CONGRATULATIONS on the purchase of your new Brinly-Hardy Aerator! Your tow at speeds higher than the maximum recommended towing speed. Aerator has been designed, engineered and manufactured to give you the best • Towing speed should always be slow enough to maintain control. Travel slowly possible dependability and performance. over rough terrain. Avoid holes, rocks and roots

Résumé du contenu de la page N° 3

PARTS REFERENCE ================================================================================================ INSTALLATION QUESTIONS? Tools Required: MISSING PARTS? (1) Flat Head Screwdriver REPLACEMENT PARTS? (1) 1/2” Wrench DON’T GO BACK (1) Set of Pliers or Hammer TO THE STORE! STOP (1) Pair of Gloves. Please call our Customer Service Department Toll-Free at 877.728.8224 or 10 www.customerservice @brinly.com 11 10 6 5 7 1 14 14 16 11 13 13 4 21 3 1 12 20 13 14 14 12 19 15 17 13 15 12

Résumé du contenu de la page N° 4

ASSEMBLY ================================================================================================ Figure 1 12 1. Install Drawbar (3) to the Tray (5) using two 5/16" X 12 1" Round Head Screws (11), two 5/16" Lock Washers 3 13 (13), and two 5/16" Hex Nuts (12) as shown in Figure 5 1. 2. Assemble the Clevis Drawbar (20) to the Drawbar (3) using two 5/16" X 1" Round Head Screws (11), two 5/16" Lock Washers (13), and two 5/16" Hex Nuts 13 (12). See Figure 1. NOTE: Install Clevis (20

Résumé du contenu de la page N° 5

ASSEMBLY ================================================================================================ CAUTION: Gloves are required when handling aerator tines. Tines have extremely sharp points. Use caution when handling. Figure 4 17 15 6. Position the 10 Tines (8) and 20 Bearings (9) onto the Tine Shaft as follows: * Bearing (9), small end fi rst * Tine (8) * Bearing (9), large end fi rst See Figure 4. NOTE: Round projections on Bearings (9) must fi t 8 into holes in Tines (8) a

Résumé du contenu de la page N° 6

OPERATION ================================================================================================ DEPTH / PENETRATION OF TINES Figure 6 CAUTION: Avoid injury! Openings in Tray allow access to Tines for cleaning and service. Excercise caution when working around Tray openings and avoid placing body parts into the openings. Bagged weight material can fall through Tray Openings and be torn open or damaged by the Tines. Use solid weight or close Tray Openings with wood panel or by ot

Résumé du contenu de la page N° 7

MAINTENANCE-STORAGE ================================================================================================ MAINTENANCE The key to years of trouble-free service is to keep your Aerator clean and dry. After the fi rst 30 minutes of use, check all fasteners for tightness. Thereafter, periodically check all fasteners for tightness. Tines are manufactured with galvanized steel to resist wear of abrasive soil. Striking objects can cause Tines to curl or break. Contact Brinly-Hardy customer

Résumé du contenu de la page N° 8

MANUFACTURER’S LIMITED WARRANTY FOR Pull Behind Accessories The limited warranty set forth below is given by Brinly-Hardy respect to any product, shall bind Brinly-Hardy Co. During Company with respect to new merchandise purchased and used the period of the warranty, the exclusive remedy is repair or in the United States, its possessions and territories. replacement of the product as set forth above. The provisions as set forth in this warranty provide the sole Brinly-Hardy Company warrants