Résumé du contenu de la page N° 1
User’s Guide
www.fetco.com
Models:
CBS-2051e
CBS-2052e
CBS-2052e20
NOTICE TO INSTALLER: Please leave this book with the machine.
Table of Contents
Contact Information ..................................................2 Programming ..........................................................10
Description & Features .............................................2 Batch Settings...............................
Résumé du contenu de la page N° 2
Contact Information FETCO® Phone: (800) 338-2699 (US & Canada) Food Equipment Technologies Company (847) 719-3000 600 Rose Road Fax: (847) 719-3001 Lake Zurich • IL • 60047-0429 • USA Email: sales@fetco.com Internet: www.fetco.com techsupport@fetco.com Description & Features The CBS-2050e Series coffee brewers feature our patented intermittent spray over technology, which works like this: The following variables are programmed for each batch size: Brew volu
Résumé du contenu de la page N° 3
Electrical Configuration and Brewing Efficiency US & Canada CBS-2051e 1.5 gallons per batch Electrical Heater Voltage Maximum Batches per Hour* (max 11) Config. Code Configuration (AC) Phase Wires KW Amp draw Cold Water Hot Water E51016 2 X 3 KW 120/208 4.6 22.1 7.7 11.0 120/220 single 3 + ground 5.1 23.4 8.6 11.0 120/240 6.1 25.5 10.3 11.0 CBS-2052e 1.5 gallons per batch Electrical Heater Voltage Maximum Batches per Hour* (max 22) Config. Code Conf
Résumé du contenu de la page N° 4
Dimensions & Utility Connections CBS-2051e DWG 201100-000 CBS-2052e DWG 201101-000 4
Résumé du contenu de la page N° 5
CBS-2052e20 DWG 201129-000 5
Résumé du contenu de la page N° 6
Installation (For Qualified Service Technicians Only) Keys To A Successful Installation If not installed correctly by qualified personnel, the brewer may not operate properly and damage may result. Damages resulting from improper installation are not covered by the warranty. Here are the key points to consider before installation: Electrical: All FETCO brewers require NEUTRAL. Ground is not an acceptable substitute. Installation without neutral may cause damage to the electron
Résumé du contenu de la page N° 7
Electrical Connection 1. Verify that the actual voltage at the electrical service connection is compatible with the specifications on the brewer’s serial number label. Make sure the electrical service includes neutral. 2. The temperature and water tank fill level are pre-set at the factory. There is no need to turn off the heaters during the installation process. The heaters are disabled by the control board until the tank is full of water. The heating process will start automatically
Résumé du contenu de la page N° 8
Final Setup 1. Turn on the incoming water supply line and inspect both inside and outside of the brewer for leaks in all fittings and tubes 2. Turn on the incoming power. 3. Press the brewer’s main power switch, which is hidden behind the front leg of the brewer. The control panel on/off switch will begin flashing. Press this switch. 4. Within 6 seconds, the hot water tank will begin filling until the water is sensed by the probe at the top of the tank. The display will read “FIL
Résumé du contenu de la page N° 9
Operating Instructions Control Panel Functions Only switches that are active are illuminated. Switches that are inactive or disabled are invisible. Main Power Switch Controls all power to brewer Indicator lamp at top of panel. Control Panel On/Off Switch Secondary power switch. Does not disconnect main power. Flashing = Off Lit = On Invisible = Main Power Off Display ”FIL” = Water tank is filling. ”LO XXX” = Unit is heating, not ready to brew. (XXX = act
Résumé du contenu de la page N° 10
Programming Display Batch Settings Turn the brewer off by pressing the main power switch. Press the main power switch again to turn the unit on. 52 The last 2 digits of the model number will display briefly, then S t b. S t b Quickly hold the STOP button for 3 seconds. P r G The display will show the software version. Example: 0.0 4.8 Press STOP to continue. Batches are numbered 1 – 3 (CBS-2051e) or 1 – 6 (CBS-2052e / 2052e20
Résumé du contenu de la page N° 11
Temperature Settings Parameter Name Range Default Setting Comment 7 Inside tank. Will be slightly lower at Water Temp. ( °F) 180 °F - 208 °F 200 °F spray head. To display in ° Celsius, see # 58 in Advanced Settings. 8 Hot Water Service A (auto) / On / Off A (auto) A= Faucet will dispense only when not brewing. On=Faucet always enabled. Off=Faucet always disabled. 9 Brew at Set 0 - 1 1 0=Will brew at any temperature Temperature above 180°F. 1=Will brew only at set temperature. N
Résumé du contenu de la page N° 12
Address Description Range Default Comment 60 Left Brew Valve 0.09 – 1.49 0.92 If #59 is GAL and Flow Rate 61 Right Brew Valve Use this to compensate for minor discrepancies in or Flow Rate actual volume versus programmed volume. Set lower to increase volume, higher to decrease 0.33 – 5.63 3.48 volume. The following formula can be used to If #59 is LTR determine the correct setting: 62 Left Bypass Valve 0.28 – 0.38 0.33 If #59 is GAL ACTUAL VOLUME and Fl
Résumé du contenu de la page N° 13
Error Codes How to Clear Error Code Description Possible Cause Corrective Action Codes 001 Internal Error Control board failure. Clear error. Turn main power System had to reload Re-program the brewer to switch off and on. default settings. the desired specifications. If error occurs again, replace control board. 050 Shorted temperature probe. Probe failure. Replace probe. Turn main power switch off and on. 051 Open temperature probe. Bad probe connection, Check all connections. Tur
Résumé du contenu de la page N° 14
Parts Figure 1 – CBS-2051e Main Assembly DWG 101191-B ITEM # QTY PART # DESCRIPTION 1 1 001049 WELDMENT CBS-2051e 2 1 57006 FILL VALVE, S-53 120VAC EXPORT 2 1 57017 FILL VALVE, S-53 220VAC 220V ONLY 3 1 24012 GASKET, S-53 FILL VALVE 4 1 31078 FITTING, S-53 FILL VALVE INLET 5 1 03074 BRACKET, S-53 6 4 82020 SCREW, S-53 FILL VALVE 7 1 31031 FITTING, 90° MALE ELBOW, 3/8 TUBE OD X 3/8 MPT 8 1 86040 CONNECTOR, CABLE CLAMP, 3/4" 9 2 86032 BUSHING, SNAP, 1" MOUNTING HOLE DIA
Résumé du contenu de la page N° 15
18 4 15007 STANDOFF, MALE-FEMALE, THREADED HEX 4-40-1/2" 19 4 29007 NUT, #4-40 KNURLED THUMB 20 1 51042 BOARD, POWER SUPPLY-120VAC EXPORT 20 1 51055 BOARD, POWER SUPPLY-220VAC 220V ONLY 21 4 29019 SPACER, .25" HEX x 1" LG., FEM, #4-40 THREAD 22 1 65002 CONNECTOR, COPPER LUG 23 1 52050 TERMINAL BLOCK 24 12 83026 WASHER, INTERNAL TOOTH LOCK, #8 SCREW SIZE, 25 1 104029 ASSEMBLY, TANK CBS-2051e 26 1 22057 INSULATION TANK FRONT CBS-2051 27 1 22058 INSULATION TANK REAR CBS-2051
Résumé du contenu de la page N° 16
Figure 2 – CBS-2051e Tank Assembly DWG 104029-C ITEM # QTY PART # DESCRIPTION 1 1 4039 WELDMENT, TANK CBS-2051e 2 1 83041 WASHER, .812"OD X .412"ID, FLAT 3 1 31005 FITTING, 90 ELBOW, 1/4 HOSE ID X 1/8 MPT 4 1 31116 LOCKNUT 1/8 STRAIGHT PIPE THREAD 5 1 83043 WASHER, 1.125"OD X 0.688"ID FLAT 6 1 83048 WASHER, 1.250"OD X 0.835"ID FLAT 7 1 31077 FITTING, 3/8 HOSE ID X 3/8 MPT 8 1 31150 FITTING, 5/8 HOSE ID X 1/2 MPT 9 1 31118 LOCKNUT 3/8 STRAIGHT PIPE THREAD 10 1 31151 LOCKNUT 1/
Résumé du contenu de la page N° 17
18 1 13072 OUTLET, INSIDE TANK HOT WATER 19 3 83042 WASHER, .875"OD X .562"ID, FLAT 20 1 31036 FITTING COMPR. MALE CONNECTOR 1/4 TUBE OD X 1/4 MPT 21 3 31117 LOCKNUT 1/4 STRAIGHT PIPE THREAD 22 1 25098 FITTING, COMPRESSION MALE CONNECTOR 23 1 31081 PLUG, HEX HEAD 1/4" MPT 24 1 24002 O-RING, TANK COVER 25 1 102013 ASSEMBLY, TANK COVER 26 2 3332 BRACKET 2, ONE SHOT THERMOSTAT 27 2 53064 THERMOSTAT, SINGLE SHOT,TRIAC 28 8 83011 WASHER, #6 SCREW SIZE, INTERNAL 29 8 84001 NUT, HEX, #6-3
Résumé du contenu de la page N° 18
Figure 3 – CBS-2052e / 2052e20 Main Assembly DWG 101197-B ITEM # QTY PART # DESCRIPTION 2 2 86021 BUSHING, SNAP, 1.375 MTG HOLE 3 2 86018 PLUG, DOME, 1.375 MOUNTING HOLE 4 2 86032 BUSHING, SNAP, 1" MOUNTING HOLE DIA 5 1 102189 ASSEMBLY, POWER BRACKET, CBS-2000e 5 1 52026 CIRCUIT BREAKER, 5A 5 1 58054 SWITCH, PUSH BUTTON 6 1 102104 ASSEMBLY, TERMINAL BLOCK 7 1 65002 CONNECTOR, COPPER LUG 8 1 57001 FILL VALVE ASSY., S-45, 120VAC EXPORT 8 1 57022 FILL VALVE ASSY., S-45, 2
Résumé du contenu de la page N° 19
EXPORT 18 1 102193 ASSEMBLY, HOT WATER VALVE, 220VAC 220V ONLY 18 57073 VALVE REBUILD KIT, DSV11. (PLUNGER, SPRING, AND DIAPHRAGM) 19 1 102202 ASSEMBLY, WATER LEVEL PROBE, CBS-2040, -50e 20 6 83051 WASHER, #8 SCREW SIZE, FLAT 21 1 002065 WELDMENT, HOT WATER FAUCET 22 1 33007 LOCKNUT, 7/16 STRAIGHT PIPE THREAD 23 1 45082 OVERLAY, CBS-2052e 24 2 102102 ASSEMBLY, LARGE SPRAY HEAD, 120V (SEE FIG 5) EXPORT 24 2 102159 ASSEMBLY, LARGE SPRAY HEAD, 220V (SEE FIG 5) 220V ONLY 25 2
Résumé du contenu de la page N° 20
Figure 4 – CBS-2052e / 2052e20 Tank Assembly DWG 104026-A ITEM # QTY PART # DESCRIPTION 1 1 004038 WELDMENT, TANK CBS-2052e 2 3 31021 BUSHING, 3/4-16 X 1/4 NPSM, HEX HEAD 3 1 84007 NUT, 3/4-16 HEX JAM 4 1 31082 FITTING, HEX NIPPLE, 3/8 MPT X 1/4 MPT 5 1 34004 VALVE, BALL 3/8 FPT X 3/8 FPT 6 1 31054 FITTING, 1/2 HOSE ID X 3/8 MPT 7 2 31027 FITTING, COMPR 90° MALE ELBOW, 3/8 TUBE OD X 1/4 MPT 8 1 31128 FITTING, 90° ELBOW, 3/8 HOSE ID X 1/4 MPT 9 1 13072 OUTLET, INSIDE TANK HOT W
