Résumé du contenu de la page N° 1
USER GUIDE
Aleratec
DVD/CD RoboRacer SA™
Part No. 280112, 280112EUR
Résumé du contenu de la page N° 2
Copyright/Model Identification The content of this manual is for informational purposes only and is subject to change without notice. This manual is copyright with all rights reserved. Under copyright laws, this manual and the software described within may not be copied, except in the normal use of the product(s) described within or to make a backup copy. Copyright© 2010 Aleratec, Inc. 9851 Owensmouth Avenue Chatsworth, CA 91311 U.S.A. www.aleratec.com Aleratec is a registered trademark an
Résumé du contenu de la page N° 3
Radio/TV Interference Statement The equipment described in this guide emits radio frequency energy. If it is not installed in accordance with the manufacturer’s instructions, it may cause interference with radio or television reception. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
Résumé du contenu de la page N° 4
Safety Regulations WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to authorized personnel only. CAUTION As the laser beam in these DVD/CD Duplicators is harmful to the eyes, do not attempt to disassemble the cabinet. Refer servicing to authorized personnel only. The use of optical instruments with this product will increase eye hazard. This DVD/CD Duplicator is classified as a CLASS
Résumé du contenu de la page N° 5
Table of Contents Introduction ..........................................................................................1 Included Items ............................................................................................1 Key Items – DVD/CD RoboRacer SA .......................................................2 DVD/CD RoboRacer SA Display Panel .....................................................3 Precautions ..............................................................................
Résumé du contenu de la page N° 6
www.aleratec.com
Résumé du contenu de la page N° 7
Introduction Thank you for purchasing this DVD/CD RoboRacer SA. Please read this User Guide thoroughly before using this product. • Page 2 shows the Key Features of the DVD/CD RoboRacer SA • Page 3 shows the Duplicator LCD Display Panel. Included Items • 1 DVD/CD RoboRacer SA • 1 Disc Output Bin Holder • 1 100-Disc Capacity Disc Output Bin • 1 50-Disc Capacity Disc Output Bin • 4 100-Disc Capacity Guide Rods • 4 50-Disc Capacity Guide Rods • 1 USB 2.0 Cable • 1 Power Cord • Software/User Guide
Résumé du contenu de la page N° 8
Introduction Key Items – DVD/CD RoboRacer SA 1 5 2 3 6 B 7 4 C 8 A 1. Clear Plastic Disc Guide Rods A. Power Plug 2. LCD Display Panel B. High Performance Cooling Fan 3. Control Panel C. USB 4. Disc Tray ControlArm 5. Disc Input Bin 6. Protective Cover 7. Disc Bin Holder 8. Disc Output Bin 2 www.aleratec.com
Résumé du contenu de la page N° 9
Introduction DVD/CD RoboRacer SA Display Panel 1 2 3 4 Multi Duplicate ESC Enter 6 5 1 Display shows all functions and messages 2 Power Indicator 3 LEFT Scroll Button 4 RIGHT Scroll Button 5 ENTER Button The left and right scroll buttons are used to navigate through the operating menu, while the enter and escape buttons are used to select or cancel menu settings. 6 ESCAPE Button www.aleratec.com 3
Résumé du contenu de la page N° 10
Precautions Before installing your DVD/CD RoboRacer SA, please read the following. Installation Avoid placing the DVD/CD RoboRacer SA in a location subject to: • High humidity • High temperature • Excessive dust • Mechanical vibration • Direct sunlight • Electromagnetic radiation Operation Do not move the DVD/CD RoboRacer SA during operation. This may cause it to malfunction during operations. Note: Choose a Good Location 1. Allow adequate clearance for moving parts. 2. When placing the duplica
Résumé du contenu de la page N° 11
Overview Main Menu This section provides a listing of the functions on the DVD/CD RoboRacer SA. Detailed descriptions of each function are given in the next section. The functions are numbered for easy reference; these numbers are also used in the next section. There are 5 main menu items that will display in the DVD/CD RoboRacer SA Display Panel. These are: Multi Duplicate Compare Image USB Mode Setup www.aleratec.com 5
Résumé du contenu de la page N° 12
Overview Subfunctions The main menu “Image” function has 4 subfunctions. These are: Image Load Image Delete Image Image Burn Image Compare 6 www.aleratec.com
Résumé du contenu de la page N° 13
Overview Subfunctions The main menu “Setup” function has 13 subfunctions. These are: Copy Mode Over Burn Mode Read Error Skip Auto Verify CD Burn Speed DVD Burn Speed Setup Default Reload Format Hard Disk Test Mode Set System Sound Erase Disc Software ID Reset Robot Input Bin Pointer 1 Pointer 2 Demo Run www.aleratec.com 7
Résumé du contenu de la page N° 14
Using the DVD/CD Duplicator Main Menu: Multi Duplicate This is the default mode of the DVD/CD RoboRacer SA controller. This function will activate the duplication process. Multi Duplicate 1. Load a source disc in the input bin and load blank discs for the number of copies needed. Multi Duplicate has a special feature that will produce copies of multiple source discs automatically. Multiple source discs can be interleaved within blank target discs loaded in the DVD/CD RoboRacer SA to produc
Résumé du contenu de la page N° 15
Using the DVD/CD Duplicator Main Menu: Compare Compare will perform a bit by bit comparison of the disc copies loaded on the input bin to the source disc. 1. Press the LEFT/RIGHT arrow keys ( ) to navigate to the “Compare” function. Compare 2. Press ENTER ( ) to begin compare. Compare Check SourceDisc 3. Load the disc to be checked. 4. Use the ESCAPE ( ) key to return to the Main Menu. Main Menu: Image Four image subfunctions manage the disc images on the built in hard disk
Résumé du contenu de la page N° 16
Using the DVD/CD Duplicator Main Menu: Image - continued Image Load “Image Load” will copy an image of a source disc loaded in the input bin to a chosen hard drive partition. 1. Press ENTER ( ) key to enter the subfunction menu. Image Load 2. Press ENTER ( ) and use the LEFT/RIGHT arrow keys ( ) to select the partition location. Select Partition No Image If there is a file size being displayed in the chosen partition, the image will be overwritten. The partitions are labele
Résumé du contenu de la page N° 17
Using the DVD/CD Duplicator 4. Press ENTER ( ) and select the partition to be compared. Select Partition A 4174MB 5. Press ENTER ( ) to start. 6. Use the ESCAPE ( ) key to return to the Main Menu. Image Burn This function will select the source image from the hard drive and burn the desired number of copies. 1. Press the LEFT/RIGHT arrow keys ( ) to navigate to the “Image” function. 2. Press ENTER ( ) key to enter the subfunction menu. 3. Press the LEFT/RIGHT arrow
Résumé du contenu de la page N° 18
Using the DVD/CD Duplicator Main Menu: Image - continued Image Delete Using this function you can select a partition to be deleted from the hard drive. 1. Press the LEFT/RIGHT arrow keys ( ) to navigate to the “Image” function. 2. Press ENTER ( ) key to enter the subfunction menu. 3. Press the LEFT/RIGHT arrow keys ( ) to navigate to the “Image Delete”. Image Delete 4. Press ENTER ( ) and select the partition to be deleted. Select Partition A 4174MB 5. Press EN
Résumé du contenu de la page N° 19
Using the DVD/CD Duplicator Main Menu: USB Mode The “USB mode” activates the connection from the DVD/CD RoboRacer SA built in hard disk drive to a PC. 1. Press the LEFT/RIGHT arrow keys ( ) to navigate to the “USB Mode” function. USB Mode 2. Press ENTER ( ) and the system will ask you if you want to enter the “USB mode”. Enter USB Mode Are you sure ? 3. Press ENTER ( ) again to make the connection. Allow the duplicator and the PC time to register the USB connection before a
Résumé du contenu de la page N° 20
Using the DVD/CD Duplicator Main Menu: USB Mode First install the Image Manager software included on the Software/User Guide CD. Using Image Manager 1. Once the Image Manager software is installed, put the RoboRacer SA into USB Mode and connect the device to your PC. 2. After Windows has finished registering the device you will have access to the HDD through the Image Manager software. 3. To load an image file to the RoboRacer SA’s HDD, start the Image Manager software. 4. The first screen
