Résumé du contenu de la page N° 1
www.DanaherMotion.com
®
Installation Instructions for SLO-SYN
MODEL SS2000MD4 Translator Drive
400030-043 Rev G
Résumé du contenu de la page N° 2
Danaher Motion Superior Electric Record of Manual Revisions ISSUE Date Description of Revision G 09/12/2003 Updated corporate information Copyright Information Copyright 1992 - 2003 Danaher Motion - All rights reserved. Printed in the United States of America. NOTICE: Not for use or disclosure outside of Danaher Motion except under written agreement. All rights are reserved. No part of this book shall be reproduced, stored in retrieval form,
Résumé du contenu de la page N° 3
Danaher Motion Superior Electric Safety Safety symbols used in this manual are: Warning Alerts users to potential physical danger or harm. Failure to follow warning notices could result in personal injury or death. Caution Directs attention to general precautions, which if not followed, could result in personal injury and/or equipment damage. Note Highlights information critical to your understanding or use of the product. Instructions Only qualified personnel should install or per
Résumé du contenu de la page N° 4
Danaher Motion Superior Electric THE FOREGOING WARRANTY IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, and of any other obligations or liabilities on the part of the Company; and no person is authorized to assume for the Company any other liability with respect to equipment manufactured by the Company. The Company shall have no liability with respect to equipment not of its m
Résumé du contenu de la page N° 5
Danaher Motion Superior Electric Table of Contents SECTION 1: INTRODUCTION.................................................................................... 6 1.1 USING THIS MANUAL.............................................................................................. 6 1.2 PRODUCT FEATURES............................................................................................... 6 SECTION 2: EXPRESS START UP ......................................................................
Résumé du contenu de la page N° 6
Danaher Motion Superior Electric SECTION 1: INTRODUCTION 1.1 USING THIS MANUAL ® It is important that you understand how this SLO-SYN 2000MD4 Translator/Drive is installed and operated before you attempt to use it. Read this manual completely before proceeding with the installation of this unit. This manual is an installation and operating guide to the SLO-SYN 2000MD4 Translator/Drive. Section 1 gives an overview of the Drive and its features. Section 2 describes the steps necessary to
Résumé du contenu de la page N° 7
Danaher Motion Superior Electric SECTION 2: EXPRESS START UP The following instructions define the minimum steps necessary to make your Drive operational. Always disconnect the AC power to the unit and be certain the "PWR ON" LED is OFF before connecting or disconnecting the motor leads. FAILURE TO DO THIS RESULTS IN A SHOCK HAZARD. Always operate the Motor and the Drive GROUNDED. Be sure to twist together the wires for each motor phase. Six twists per foot is a good guideline. 1.
Résumé du contenu de la page N° 8
Danaher Motion Superior Electric Section 3: Installation Guidelines 3.1 MOUNTING The SLO-SYN Drive is mounted by fastening its mounting brackets to a flat surface as shown in Figure 3.1. If the drive assembly is mounted against a bulkhead, be sure to apply a thin coating of thermal compound between the drive and the mounting surface before fastening the unit in place. Do not use too much thermal compound. It is better to use too little than too much. Figure 3.1 Mounting Diagram Case
Résumé du contenu de la page N° 9
Danaher Motion Superior Electric 3.2 TERMINAL LOCATIONS AND ASSIGNMENTS Figure 3.2 shows the terminal locations for the SLO-SYN SS2000MD4 Translator/Drive. I/O Connector (J2) Motor And Power Supply Connector (J1) Figure 3.2, Terminal Locations SS2000MD4 9 400030-043 Rev G
Résumé du contenu de la page N° 10
Danaher Motion Superior Electric 3.3.1 Motor Connections All motor connections are made via the 6-terminal strip (J1). Terminal assignments are given below. Motor connections are shown in Figure 3.3. J1 Pin Assignment 1 M1 (Phase A+) 2 M3 (Phase A-) 3 M4 (Phase B+) 4 M5 (Phase B-) Motor phase A is M1 and M3 and motor phase B is M4 and M5. The motor frame must be grounded. Cabling from the drive to the motor should be done with a shielded, twisted pair cable. As a
Résumé du contenu de la page N° 11
Danaher Motion Superior Electric MOTOR MOTOR TERMINAL "M" NUMBERS MOTOR CONNECTOR PIN CONNECTOR PIN WHITE/ 1 5 DRIVE PIN 1 RED B D DRIVE PIN 4 BLACK WHITE/ DRIVE PIN 2 H F BLACK DRIVE PIN 3 3 4 RED GREEN 4-LEAD MOTORS DRIVE PIN 1 1 5 DRIVE PIN 4 RED B D GREEN * N.C. 2 WHITE BLACK G 6 E N.C.* WHITE/ WHITE/ DRIVE PIN 2 DRIVE PIN 3 H F 3 4 RED GREEN 6-LEAD MOTORS DRIVE PIN 1 1 5 RED B D GREEN DRIVE PIN 4 BLACK G E ORANGE 6 7 * WHITE/ * 2 8 WHITE A C BLACK WHITE/ WHITE/ DRIVE PIN 2 H F DRIVE PIN 3
Résumé du contenu de la page N° 12
Danaher Motion Superior Electric 3.3.2 Power Input The DC input power is connected to terminals 5 and 6 of the terminal strip (J1). Terminal 5 [Vm(+)] is the power supply plus (+) connection and pin 6 [Vom(-)] is the power supply minus (-) connection. An unregulated supply similar to that shown in Figure 3.4 is preferable. If a regulated supply is used, it must be capable of operating with the added filter capacitor. A switching regulated supply may not be suitable for use with this driv
Résumé du contenu de la page N° 13
Danaher Motion Superior Electric SECTION 4: SPECIFICATIONS 4.1 MECHANICAL Size (Inches) 1.56 H x 4.13 W x 3.25 D (mm) 40 H x 105 W x 83 D Weight 0.6 pounds (272 grams) 4.2 ELECTRICAL DC Input Range............ 24 VDC min., 40 VDC max. DC Current ................... see Motor Table Drive Power Dissipation (Worse Case)..... 35 watts 4.3 ENVIRONMENTAL Temperature Operating +32° F to +122° F (0° C to +50° C) free air ambient, Natural Convection. Maximum heat sink temp
Résumé du contenu de la page N° 14
Danaher Motion Superior Electric MOTORS FOR USE WITH THE SS2000MD4 TRANSLATOR/DRIVE Current Power Supply Current Setting Standstill Maximum Motor Winding Connection (Amperes) (Amps. DC) (Amps. DC) M061 08 Series 2.5 1.0 2.0 M061 08 Parallel 3.5 1.0 2.0 M062 09 Series 3.0 1.0 2.5 M062 09 Parallel 3.5 1.0 3.5 M063 09 Series 3.0 1.5 2.0 M063 09 Parallel 3.5 1.0 3.5 M091 09 Series 3.0 1.0 1.5 M091 09 Parallel 3.5 1.0 3.0 M092 09 Series 3.0 1.5 2.0 M092 09 Parallel 3.5 1.0 3.0 KM
Résumé du contenu de la page N° 15
Danaher Motion Superior Electric 4.5 CURRENT SETTINGS The proper current setting for each motor is shown on the individual torque vs. speed curves. Use this current level to obtain the torque shown. Switches 1 through 7 select the current level. Select the desired operating current by setting the appropriate switch to position 1 (ON). The OFF position is labeled "0". Only one switch should be ON. If two or more switches are ON, the one that selects the highest current level is the active
Résumé du contenu de la page N° 16
Danaher Motion Superior Electric 4.7 SIGNAL SPECIFICATIONS 4.7.1 Connector Pin Assignments All connections are made via the 4-pin terminal strip (J2). Pin Assignment 1 OPTO 2 PULSE 3 DIR 4 AWO 4.7.2 Signal Descriptions OPTO Opto-Isolator Supply User supplied power for the opto-isolators. PULSE Pulse Input A low to high transition on this pin advances the motor one step. The step size is determined by the Step Resolution switch setting. DIR Direction Input When this signal is h
Résumé du contenu de la page N° 17
Danaher Motion Superior Electric 4.7.4 Timing Requirements PULSE Max. Frequency....... 20 kHz Max. Rise and Fall Times................ 1 microsecond Min. Pulse Width ....................... 25 microseconds Other Signals Response Time ....... 25 microseconds OPTO IN 12 VDC, 16 mA PER SIGNAL 560 ohms PULSE CONTROL SIGNAL 1/4 watt DRIVE CONTROL LOGIC COMMON OPTO IN 4.5 - 6.0 VDC, 16 mA PER SIGNAL PULSE CONTROL SIGNAL DRIVE CONTROL LOGIC COMMON OPTO IN 4.5 - 6.0 VDC, 16 mA PER SIGNAL PULS
Résumé du contenu de la page N° 18
Danaher Motion Superior Electric SECTION 5: TORQUE VERSUS SPEED CHARACTERISTICS 5.1 MOTOR PERFORMANCE All stepper motors exhibit instability at their natural frequency and harmonics of that frequency. Typically, this instability occurs at speeds between 50 and 1000 full steps per second and, depending on the dynamic motor load parameters, cause excessive velocity modulation or improper positioning. This type of instability is represented by the open area at the low end of each Torque
Résumé du contenu de la page N° 19
Danaher Motion Superior Electric 5.2 TYPICAL TORQUE VERSUS SPEED CURVES The test conditions used when obtaining the torque versus speed data are listed in the lower left-hand corner of each curve. SS2000MD4 19 400030-043 Rev G
Résumé du contenu de la page N° 20
Danaher Motion Superior Electric SS2000MD4 20 400030-043 Rev G
