Résumé du contenu de la page N° 1
PX865PEC PRO(2.0)
Copyright
All rights are reserved. No part of this publication may be reproduced, transmitted, transcribed,
stored in a retrieval system or translated into any language or computer language, in any form or by
any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the
prior written permission of the company. Brands and product names are trademarks or registered
trademarks of their respective companies.
The vendor makes no represen
Résumé du contenu de la page N° 2
Things You have to know !!! The images and pictures in this manual are for reference only and may vary slightly from actual product installation depending on specific hardware models, third party components and software versions. Unplug any power connector when installing components and configuring switches and pins on the mainboard. This mainboard contains very delicate IC chips. Use a grounded wrist strap when working with the system. Do not touch the IC chips, leads, connectors
Résumé du contenu de la page N° 3
PX865PEC PRO(2.0) ® Intel 865PE & ICH5 ® ® Supports Socket 478 Intel Pentium 4 Processor User Manual Enabling the Hyper-Threading Technology, your computer system is required as the following components: ® ® CPU: An Intel Pentium 4 Processor with HT Technology ® Chipset: An Intel Chipset that supports HT Technology BIOS: A BIOS that supports HT Technology and has it enabled OS: An operating system that supports HT Technology For more information on
Résumé du contenu de la page N° 4
Contents CHAPTER 1. GETTING STARTED ............................................................1 INTRODUCTION.......................................................................................................... 1 SPECIFICATION.......................................................................................................... 2 CONFIGURATION ....................................................................................................... 5 Layout of PX865PEC PRO(2.0).......
Résumé du contenu de la page N° 5
Chapter 1. Getting Started Introduction Thanks for choosing the PX865PEC PRO(2.0) mainboard! It is based on the 865PE Northbridge ® ® chipset and the ICH5 Southbridge chipset. It supports Intel Pentium 4 (Northwood/ Prescott) Processors with FSB (Front Side Bus) 800/533/400 MHz. The PX865PEC PRO(2.0) mainboard provides 4 sockets using 184-pin DDR SDRAM with a total capacity of up to 4GB. You can install unbuffered & non-ECC DDR400/ 333/ 266 (PC3200/ 2700/ 2100) SDRAM. The PX865PEC PR
Résumé du contenu de la page N° 6
Specification CPU: ® ® Support Socket 478 Intel Pentium 4 processor (Northwood/ Prescott) Support Hyper Threading Technology Chipset: ® Northbridge Chip (MCH) – Intel 865PE ® Southbridge Chip (ICH) – Intel ICH5 I/O Controller – ITE IT8712F AC’97 Audio Codec – ALC655 LAN Controller – RTL8100C DRAM Memory: Support DDR400 (PC3200)/ 333 (PC2700)/ 266 (PC2100) SDRAM Support 64 MB/128 MB/256 MB/512 MB/1 GB unbuffered & non-ECC DDR memory modules Single channel DDR400 memo
Résumé du contenu de la page N° 7
AC’97 Sound Codec Onboard: High performance CODEC with high S/N ratio (>90 dB) Compliant with AC’97 2.3 specification Support 6-channel playback capability (Super 5.1 Channel Audio Effect) Support 3D Stereo enhancement Support Sony/ Philips Digital Interface (S/PDIF) function LAN Chip onboard: 10/100 Mbps Ethernet supported I/O facilities: One Multi-parallel Port capable of supporting the following specifications: 1. Standard & Bi-direction Parallel Port 2. Enhanced Para
Résumé du contenu de la page N° 8
Watch Dog Timer: This mainboard contains a special feature called the “Watch Dog Timer” which is used to detect when the system is unable to handle over-clocking configurations during the POST stage. Once a problem is detected the system will reset the configurations and reboot the system after five seconds. 4
Résumé du contenu de la page N° 9
Configuration Layout of PX865PEC PRO(2.0) 5
Résumé du contenu de la page N° 10
Hardware Installation This section will assist you quickly in installing your system hardware. Wear a wrist ground strap before handling components. Electrostatic discharge may damage your system components. CPU Processor Installation ® ® This mainboard supports Intel Pentium 4 processors using a Socket 478. Before building your system, we suggest you to visit the Intel website and review the processor installation procedures. http://www.intel.com CPU Socket 478 Configuration Steps: Loc
Résumé du contenu de la page N° 11
FAN Headers: JCFAN1、JSFAN1 Two power headers are available for cooling fans, which play an important role in maintaining the ambient temperature in your system. Attention We strongly recommend that you use a CPU fan sink with your CPU. You can attach the CPU fan to the JCFAN1 Header. Memory Installation The mainboard contains 4 memory modules which using 184-pin DDR SDRAM with a total memory capacity of up to 4 GB. You can install unbuffered & non-ECC D
Résumé du contenu de la page N° 12
To Enable Dual-Channel DDR, the following conditions must be met: 1.You must insert either DDRA1 & DDRA2 together or DDRB1 & DDRB2 together or all four memory modules together. 2.You must insert the same memory configurations between DDRA1 & DDRA2, and DDRB1 & DDRB2. Same memory density (128MB, 256MB, 512MB, etc.) Same memory technology (128Mb, 256Mb, or 512Mb) Same memory bus width (x8 or x16) Both either single-sided or dual-sided memory modules Same brand memory Same c
Résumé du contenu de la page N° 13
Lower the memory module into the socket and press firmly using both thumbs until the module snaps into place. Repeat step 1, 2 & 3 for the remaining memory modules setting. ＊ The pictures shown above are for reference only. Your mainboard configuration may vary with the pictures shown. Back Panel Configuration PS/2 Mouse & Keyboard Connectors: JKBMS1 This mainboard provides a standard PS/2 mouse connector and PS/2 Keyboard connector. The pin assignm
Résumé du contenu de la page N° 14
Parallel Interface Port: JPRNT1 The parallel port on your system has a 25-pin connector and is used to connect parallel printers and other devices which are able to support with this port. The Serial Interface: COM1 This mainboard provides a serial port COM1 on the back panel, and is used to connect mice, modems and other peripheral devices. You can also connect your computer to another one through this serial port, in order to transfer data or information from your hard drive disk.
Résumé du contenu de la page N° 15
Speaker-Out (Green) It is a standard audio port for connecting the speaker or headphone connectors. When the Super 5.1 Channel Audio driver installed and enabled, your front speaker function will be enabled with this port. In addition, if you enable the Super 5.1 Channel Audio Effect but using the Standard 2 channel audio function, we suggest you to connect this port, so that the outputed sounds can be high fidelity. Mic In (Pink) This port is for connecting a microphone to input your vo
Résumé du contenu de la page N° 16
Connector Connector 21 +5V 22 Ground 23 IRTX 24 IRRX SPK (Speaker Connector) A front panel speaker can be connected to this header. When you reboot the computer, the speaker will sound a short “beep”. If there is something wrong during the Power On Self-Test, the speaker otherwise will sound “irregular beep” to warn you. HLED (Hard Drive LED Header) This header can be connected to an HLED on the front panel of a computer case. The HLED will flicker during the hard drive disk (HDD) activ
Résumé du contenu de la page N° 17
Connectors Floppy Drive Disk Connector: FDD1 The mainboard provides a standard floppy drive connector (FDC) that supports 360K, 720K, 1.2M, 1.44M and 2.88M floppy disks. This connector supports the floppy drive ribbon cables provided in the packaging. Hard Drive Disk Connectors: IDE1/ IDE2、SATA1/ SATA2 The mainboard has a 32-bit enhanced IDE Controller that supports Ultra ATA 33, Ultra ATA 66, Ultra ATA 100 and Ultra ATA 133. It has two IDE slots, IDE1 and IDE2 for connecting th
Résumé du contenu de la page N° 18
Headers & Jumpers Front USB Headers: JUSB2/ JUSB3 This mainboard provides 4 USB ports and 2 USB headers on the mainboard which allowing you to use 4 additional USB ports. An optional USB bracket may be included with this product. The bracket is typical secured to the back side of your computer case and has standard USB ports that you can connect to external USB devices. The bracket will also have cables that you can extend to the JUSB2 or JUSB3 headers. USB Power Source Hea
Résumé du contenu de la page N° 19
Clear CMOS Jumper: JCMOS1 The “Clear CMOS” function is used when you cannot boot your system due to some CMOS problems, such as a password is forgotten. This jumper allows you to reset the CMOS configurations, and then reconfigure it. The following steps explain how to reset your CMOS configurations when you have forgotten your system password. 1. Turn off your system and disconnect the AC power cable. 2. Set JCOMS1 to OFF (2-3 Closed). 3. Wait several seconds. 4
Résumé du contenu de la page N° 20
Audio Connectors This mainboard provides three connectors as part of its audio Subsystem. CD-ROM Audio-In Header: JCDIN1 This header is used to connect to a CD-ROM / DVD audio cable. S/PDIF (Sony/Philips Digital Interface) Headers:SPDIF_IN1/OUT1 S/PDIF is a recent audio transfer file format, which provides high quality audio using optical fiber and digital signals. This mainboard is capable of delivering audio output and receiving audio input through the SPD
