Instruction d'utilisation Vantec UGT-PC2S1P

Résumé du contenu de la page N° 1

2+1 SERIAL & PARALLEL PCI
HOST CARD


User Manual
Model: UGT-PC2S1P




All brand names and trademarks are properties of their respective owners.
w ww.vantecusa.com

Résumé du contenu de la page N° 2

Features and Benefits Compliant with PCI Local Bus Specification, Revision 2.3 Supports 2 x UART serial ports Add one IEEE 1284 Parallel Port on system Easy Plug and Play Automatically selects IRQ & I/O address Built-in 16C450/550 compatible UART On chip 256 byte FIFOs in transmit and receive path of each serial port Serial data transfer rate up to 115200bps Supports Standard Parallel Port (SPP), Enhanced Parallel (EPP) & Enhanced Capability Port (ECP) Parallel data t

Résumé du contenu de la page N° 3

Specifications Model: UGT-PC2S1P Bus interface: PCI 32-bit Ports: 2 x External Serial Port (DB9 Male) 1 x External Parallel Port (DB25 Female) Dimension : 142 x 120 x 18mm OS Support : Windows® 2000, XP/2003/Vista/2008/7 (32/64 bit) System Requirements Windows® 2000, XP/2003/Vista/2008/7 (32/64 bit) Computer with one available PCI slot (CD-Rom Drive May Be Needed For Drivers) Package Contents 1 x 2+1 SERIAL & PARALLEL PCI HOST CARD 1 x

Résumé du contenu de la page N° 4

Layout Before Installing the Vantec 2+1 SERIAL & PARALLEL PCI HOST CARD, please see the photo below highlighting the available Parallel, Serial ports of the card. P1 & P2: Serial Ports P3: Parallel Port UGT‐PC2S1P                                    Page  4 

Résumé du contenu de la page N° 5

Hardware Installation 1. Turn off the power to your computer. 2. Unplug the power cord and remove your computer’s cover. 3. Remove the slot bracket from an available PCI slot. 4. To install the 2+1 SERIAL & PARALLEL PCI HOST CARD, carefully align the card’s bus connector with the selected PCI slot on the motherboard. Push the board down firmly. 5. Replace the slot bracket’s holding screw to secure the card. 6. Replace the computer cover and reconnect the power cord. Driver Installatio

Résumé du contenu de la page N° 6

For Windows® XP/2003/Vista/2008/7 32bit 1. At the Windows desktop click Start, then Run. 2. Type D:\UGT-PC2S1P\XP_2003_2008_Vista_7\32bit\PciSetup.exe, then click OK. 3. Press “Install” button to install the drivers. 4. Click “Exit” button. 5. Restart Windows to complete the installation. For Windows® XP/2003/Vista/2008/7 64bit 1. At the Windows desktop click Start, then Run. 2. Type D:\UGT-PC2S1P\XP_2003_2008_Vista_7\64bit\PciSetup.exe, then click OK. 3. Press “Install” button to

Résumé du contenu de la page N° 7

To Verify Windows® Driver Installation Click on the Device Manager tab in System Properties, which you access from the Windows Control Panel. You should see two High-Speed PCI Serial Port … and one PCI ECP Parallel Port … installed under Ports (COM & LPT) item. UGT‐PC2S1P                                    Page  7 

Résumé du contenu de la page N° 8

Warranty The 2+1 SERIAL & PARALLEL PCI HOST CARD comes with a 1 year limited warranty (90 day parts). If your unit becomes defective within that time frame, please go to www.vantecusa.com for information on how to receive warranty exchange or repair. Cosmetic defects and missing parts are not covered under this warranty. Please check the contents of the unit to make sure you received all parts. Also, check for any cosmetic flaws. If any parts are missing or if there are cosmetic defects,