Résumé du contenu de la page N° 1
Résumé du contenu de la page N° 2
English SAFETY SYMBOLS This manual uses the safety symbols below. They denote critical information. Please read them carefully. WARNING Failure to abide by the information in a WARNING may result in serious injury and can be life threatening. CAUTION Failure to abide by the information in a CAUTION may result in moderate injury and/or property or product damage. Indicates a prohibited action. Indicates to ground for safety. Copyright© 2003 by EIZO NANAO CORPORATION.
Résumé du contenu de la page N° 3
English TABLE OF CONTENTS PRECAUTIONS.....................................................................................4 1. INTRODUCTION .....................................................................................9 1-1. Features ........................................................................................................9 1-2. Package Contents..........................................................................................9 1-3. Controls & Connectors ......
Résumé du contenu de la page N° 4
English PRECAUTIONS IMPORTANT! • This product has been adjusted specifically for use in the region to which it was originally shipped. If operated outside the region to which it was originally shipped, the product may not perform as stated in the specifications. • To ensure personal safety and proper maintenance, please read this section and the caution statements on the unit (refer to the figure below). [Location of the Caution Statements] WARNING If the unit begins to emit s
Résumé du contenu de la page N° 5
English WARNING Keep small objects or liquids away from the unit. Small objects accidentally falling through the ventilation slots into the cabinet or spillage into the cabinet may result in fire, electric shock, or equipment damage. If an object or liquid falls/spills into the cabinet, unplug the unit immediately. Have the unit checked by a qualified service engineer before using it again. Place the unit at the strong and stable place. A unit placed on an inadequate surface
Résumé du contenu de la page N° 6
English WARNING Use the correct voltage. * The unit is designed for use with a specific voltage only. Connection to another voltage than specified in this User’s Manual may cause fire, electric shock, or equipment damage. * Do not overload your power circuit, as this may result in fire or electric shock. Handle the power cord with care. * Do not place the cord underneath the unit or other heavy objects. * Do not pull on or tie the cord. If the power cord becomes damaged, stop
Résumé du contenu de la page N° 7
English CAUTION Handle with care when carrying the unit. Disconnect the power cord and cables when moving the unit. Moving the unit with the cord attached is dangerous. It may result in injury. When handling the unit, grip the bottom of the unit firmly with both hands ensuring the panel faces outward before lifting. Dropping the unit may result in injury or equipment damage. OK Do not block the ventilation slots on the cabinet. * Do not place any objects on the venti
Résumé du contenu de la page N° 8
English LCD Panel In order to suppress the luminosity change by long-term use and to maintain the stable luminosity, use of a monitor in lower brightness is recommended. The screen may have defective pixels. These pixels may appear as slightly light or dark area on the screen. This is due to the characteristics of the panel itself, and not the product. The backlight of the LCD panel has a fixed life span. When the screen becomes dark or begins to flicker, please contact your deale
Résumé du contenu de la page N° 9
English 1. INTRODUCTION Thank you very much for choosing an EIZO Color Monitor. 1-1. Features • Dual inputs compliant • DVI (p. 28) Digital input (TMDS (p. 29)) compliant • [Horizontal scanning frequency] Analog: 31.5 - 80 kHz, Digital: 31.5 - 64 kHz [Vertical scanning frequency] Analog: 56 - 75.1 Hz Vertical Digital: 59 - 61 Hz (VGA text: 69 - 71 Hz) [Resolution] 1280 dots x 1024 lines • Auto Screen Adjustment function incorporated (p. 18) • BrightRegulator function incorporat
Résumé du contenu de la page N° 10
English 1-3. Controls & Connectors Front (6) (1) Control Panel (2) (3) (4) (5) ® (1) ScreenManager *1 (2) Control Buttons (Left, Right) (3) Enter Button (4) Power Button *2 (5) Power Indicator Blue Operation Yellow Power saving Off Power off *3 (6) Sensor *1 Pressing the Control buttons without displaying ScreenManager Left Control Button Switching the input signals (p. 14) Right Control Button Displaying the Brightness Adjustment menu (p. 19) *2 Regarding the p
Résumé du contenu de la page N° 11
English Rear (10) (11) (12) Bottom (7) (8) (9) (7) Power Connector (8) DVI-D Input Connector (9) D-Sub mini 15 pin Input Connector *4 (10) 4 Holes for Mounting an Arm-Stand *5 (11) Security Lock Slot (12) Stand *4 The LCD monitor can be used with an optional arm stand by folding the stand, see p. 22. *5 Allows for connection of a security cable. This lock supports Kensington’s MicroSaver security system. For further information, please consult: Kensington Tech
Résumé du contenu de la page N° 12
English 2. CABLE CONNECTION 2-1. Before connecting Before connecting your monitor to the PC, change the display screen settings (resolution (p. 28) and frequency) in accordance with the charts below. NOTE • When your computer and display support VESA DDC, the suitable resolution and the refresh rate are set by just plugging your display into the computer without any manual settings. Analog Input Resolution Frequency Dot Clock Remarks 640 x 480 ~75 Hz VGA, VESA 640 x 480 67 Hz Apple
Résumé du contenu de la page N° 13
English 2-2. Connecting the signal cable NOTE • Be sure that the Power buttons of both the PC and the monitor are OFF. 1. Set up the monitor after unfolding the base of the stand. NOTE • How to adjust Angles of the Monitor Grip upper side of the monitor firmly with both hands and adjust the monitor angle as desired. 2. Plug the signal cable into the connector at the rear of the monitor and the other end of the cable into the video connector on the PC. After connecting, secure the
Résumé du contenu de la page N° 14
English 3. Plug the power cord into the power connector on the rear of the monitor. Then, plug the other end of the cord into a power outlet. WARNING Use the enclosed power cord and connect to the standard power outlet of your country. Be sure to remain within the rated voltage of the power cord. Not doing so may result in fire or electric shock. The equipment must be connected to a grounded main outlet. Not doing so may result in fire or electric shock. 4. Turn on the m
Résumé du contenu de la page N° 15
English 3. ScreenManager 3-1. How to use the ScreenManager Main Menu Control Panel Power Button Enter Button Right Control Button Left Control Button (To select the desired sub (To select the desired sub menu to the right / upward menu to the left / downward and adjust) and adjust) 1. Entering the ScreenManager Press the Enter button once to display the main menu of the ScreenManager. 2. Making Adjustments and Settings (1) Select the desired sub menu icon using the Contr
Résumé du contenu de la page N° 16
English 3-2. ScreenManager Adjustments and Settings The following table shows all the ScreenManager’s adjustment and setting menus. “*” indicates adjustments of analog input only. Main menu Sub menu Reference Auto Adjustment Screen * 4-1. Auto Screen Adjustment (p. 18) Range * Screen Clock * Adjust the Clock (p. 28). Phase * Adjust the Phase (p. 28). Hor. Position * Adjust the Horizontal Position. Ver. Position * Adjust the Vertical Position. Color sRGB 4-4. Color Adjust
Résumé du contenu de la page N° 17
English 3-3. Useful Functions Adjustment Lock Use the “Adjustment Lock” function to prevent any accidental changes. Locked function • Settings in the ScreenManager Unlocked function • BrightRegulator function • Adjusting the brightness by the right control button • Switching the input signal by the left control button • Turning the power on and off by the Power button [To lock] (1) Switch off the monitor’s power by the Power button. (2) Press on the Enter button while switching on
Résumé du contenu de la page N° 18
English 4. ADJUSTMENT Adjust the screen by refering to the followings in each input signals. • Analog input : Adjust the screen by refering from “4-1. Auto Screen Adjustment” to “4-4. Color Adjustment”. • Digital input : Adjust the screen by refering from “4-3. Brightness Adjustment” to “4-4. Color Adjustment”. 4-1. Auto Screen Adjustment Screen flickering is suppressed and the proper position is adjusted automatically in the following cases. • When the monitor is input the input si
Résumé du contenu de la page N° 19
English 4-3. Brightness Adjustment BrightRegulator Function BrightRegulator function adjusts the brightness of the screen automatically depending on the surrounding brightness. The brightness of backlight is adjusted as the sensor on the upper side of the monitor detects the surrounding brightness (Default: this function is set “Enable”.) [To deactivate this function] (1) Select in the ScreenManager menu. (2) Select “Disable”. NOTE • Do not block the s
Résumé du contenu de la page N° 20
English 4-4. Color Adjustment The menu in the ScreenManager enables to change the color of the screen. In this menu, (p. 29) can be set and (p. 28) can be adjusted. In the analog input, perform the “Range Adjustment” (p. 18) before making the color adjustments. To display the screen image based on those original colors (ex. Over the Internet) → Select . Select “On”. To change each color (red, green and blue) → Use the (p. 28) adjustment By adju
