Résumé du contenu de la page N° 1
® TM
MultiSync LCD1860NX
LCD1860NX_Cover.p65 1 10/28/02, 4:30 PM
Résumé du contenu de la page N° 2
Index Warning .................................................................................................................... 1 Contents ................................................................................................................. 2 Quick Start ............................................................................................................. 3 Controls .............................................................................................................
Résumé du contenu de la page N° 3
WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PL
Résumé du contenu de la page N° 4
Contents ® Your new NEC MultiSync LCD monitor box* should contain the following: ™ • MultiSync LCD1860NX monitor with tilt base • Power Cord • Video Signal Cable • User’s Manual Power Cord Video Signal Cable User’s Manual ® TM MultiSync LCD1860NX * Remember to save your original box and packing material to transport or ship the monitor. 2 LCD1860NXManual102802.p65 2 10/28/02, 5:15 PM
Résumé du contenu de la page N° 5
Quick Start ® To attach the MultiSync LCD monitor to your system, follow these instructions: 1. Turn off the power to your computer. 2. For the PC or MAC with DVI digital output: Connect the DVI signal cable (not included) to the connector of the display card in your system (Figure A.1). Tighten all screws. For the PC with Analog output: Connect the 15-pin mini D-SUB signal cable to the connector of the display card in your system (Figure A.2). Tighten all screws. For the MAC: Connect the Multi
Résumé du contenu de la page N° 6
Quick Start –continued Figure C.1 Figure C.2 Figure D.1 Vacation Switch Power Button 4 LCD1860NXManual102802.p65 4 10/28/02, 5:15 PM
Résumé du contenu de la page N° 7
Quick Start –continued Tilt and swivel Grasp both sides of the monitor screen with your hands and adjust the tilt and swivel as desired (Figure TS.1). Remove Monitor Stand for Mounting To prepare the monitor for alternate mounting purposes: 1.Disconnect all cables. Figure TS.1 2.Place monitor face down on a non-abrasive surface (Figure R.1). 3.Remove the hinge cover P PUSH USH P PUSH USH Hinge cover (Figure R.1). 4.Remove the 4 screws connecting the monitor to the stand and lift off the stand as
Résumé du contenu de la page N° 8
Quick Start –continued This LCD monitor is designed for use with a flexible arm. Please use the attached screws (4pcs) as shown in the picture when installing. To meet fhe safety requirements, the monitor must be mounted to an arm which guaranties the necessary stability under consideration of the weight of the monitor. The LCD monitor shall only be used with an approved arm (e.g. GS mark). Thickness of Bracket(Arm) 2.0~3.2mm Tighten all screws. 100mm 100mm Specifications If using other screws,
Résumé du contenu de la page N° 9
Controls ® OSM (On-Screen Manager) control buttons on the front of the monitor function as follows: To access OSM menu, press any of the control buttons (EXIT, <, >, –, +). To change signal input, press the SELECT/1÷ 2 button. NOTE: OSM must be closed in order to change signal input. Menu EXIT Exits the OSM controls. Exits to the OSM main menu. < / > Moves the highlighted area left/right to select control menus. Moves the highlighted area up/down to select one of the controls. –/+ Moves the bar
Résumé du contenu de la page N° 10
Controls –continued are standard and cannot be changed). Color temperature increases or decreases, in each preset. R,Y,G,C,B,M,S: Increases or decreases Red, Yellow, Green, Cyan, Blue, Magenta and Saturation depending upon which is selected. The change in color will appear on screen and the direction (increase or decrease) will be shown by the color bars. NATIVE: Original color presented by the LCD panel that is unadjustable.. Tools 1 SHARPNESS: This function is digitally capable to keep crisp
Résumé du contenu de la page N° 11
Controls –continued Tools 2 LANGUAGE: OSM control menus are available in seven languages. OSM POSITION: You can choose where you would like the OSM control image to appear on your screen. Selecting OSM Location allows you to manually adjust the position of the OSM control menu left, right, down or up. OSM TURN OFF: The OSM control menu will stay on as long as it is use. In the OSM Turn Off submenu, you can select how long the monitor waits after the last touch of a button to shut off the OSM con
Résumé du contenu de la page N° 12
Recommended Use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING ® THE MULTISYNC LCD COLOR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel. • Do not spill any liquids into the cabinet or use your monitor near water. • Do not insert objects of any kind into the cabin
Résumé du contenu de la page N° 13
Recommended Use –continued CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for warm-up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen. • Position your monitor no closer than 16 inches and no further away than 28 inches from your eyes. Th
Résumé du contenu de la page N° 14
Specifications ® ™ Monitor MultiSync LCD1860NX Notes Specifications Monitor LCD Module Diagonal : 18.1 inch Active matrix; thin film transistor (TFT) Viewable Image Size : 18.1 inch liquid crystal display (LCD); 0.28 mm dot 2 Native Resolution (Pixel Count) : 1280 x 1024 pitch; 200cd/m white luminence; 350:1 contrast ratio, typical Input Signal Video : ANALOG 0.7 Vp-p/75 Ohms Digital Input: DVI Sync : Separate sync. TTL Level Horizontal sync. Positive/Negative Vertical sync. Positive/Negative Di
Résumé du contenu de la page N° 15
Features Reduced Footprint: Provides the ideal solution for environments requiring superior image quality but with size and weight limitations. The monitor’s small footprint and low weight allow it to be moved or transported easily from one location to another. ® AccuColor Control Systems: Six color presets select the desired color setting (sRGB and NATIVE color presets are standard and cannot be changed). R,G,B: Increases or de- creases Red, Green or Blue color depending upon which is selected
Résumé du contenu de la page N° 16
Troubleshooting No picture • The signal cable should be completely connected to the display card/computer. • The display card should be completely seated in its slot. • Check the Vacation Switch should be in the ON position. • Front Power Switch and computer power switch should be in the ON position. • Check to make sure that a supported mode has been selected on the display card or system being used. (Please consult display card or system manual to change graphics mode.) • Check the monitor and
Résumé du contenu de la page N° 17
References NEC-Mitsubishi Monitor Customer Service & Support Customer Service and Technical Support: (800) 632-4662 Fax: (800) 695-3044 Parts and Accessories/Macintosh Cable Adapter: (888) NEC-MITS [888-632-6487] Customer Service Policies & Processes: http://www.necmitsubishi.com/ css/ServicePolicies/ServicePolicies.htm Online Technical Support Knowledge Base: http://www.necmitsubishi.com/ css/knowledgebase.cfm Customer Service & Technical Support Email: http://www.necmitsubishi.com/ css/tech
Résumé du contenu de la page N° 18
Limited Warranty NEC-Mitsubishi Electronics Display of America, Inc. (hereinafter “NMD-A”) warrants this Product to be free from defects in material and workmanship and, subject to the conditions set forth below, agrees to repair or replace (at NMD-A’s sole option) any part of the enclosed unit which proves defective for a period of three (3) years from the date of first consumer purchase. Spare parts are warranted for ninety (90) days. Replacement parts or unit may be new or refurbished and wil
Résumé du contenu de la page N° 19
TCO’95 MultiSync LCD1860NX (L182R4) Black Model Congratulations! You have just purchased a TCO’95 approved and labeled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also, to the further development of environmentally adapted electronics products. Why do we have environmentally labelled computers? In many countries, environmental labelling has become an established method for en
Résumé du contenu de la page N° 20
TCO’95 –continued reproductive damage in fisheating birds and mammals, due to the bio-accumulative* processes. Flame retardants have been found in human blood and researchers fear that disturbances in foetus development may occur. TCO’95 demand requires that plastic components weighing more than 25 grams must not contain organically bound chlorine and bromine. Lead** Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous system and in higher doses,
