Résumé du contenu de la page N° 1
NEC Flat Professional Series
®
®
MultiSync
MultiSync
™
™
FP950
FP950
™
™
FP1350
FP1350
User’s Manual
User’s Manual
78134171 1 12/3/98, 4:09 PM
Résumé du contenu de la page N° 2
Index Warning 1 Contents 2 Quick Start 3-5 Controls 6-9 Recommended Use 10-11 Specifications 12-13 Features 14 Troubleshooting 15 References 16 Limited Warranty 17 TCO’99 18-19 Avertissement 21 Contenu 22 Mise en marche rapide 23-25 Commandes 26-29 Usage recommandé 30-31 Fiche technique 32-33 Fonctions 34 Dépannage 35 Références 36 Garantie limitée 37 TCO’99 38-39 Warnung 42 Lieferumfang 43 Quick Start 44-46 Bedienungselemente 47-50 Empfehlungen für die Verwendung 51-52 Technische Daten 53-54 Fu
Résumé du contenu de la page N° 3
WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PL
Résumé du contenu de la page N° 4
NEC MultiSync Monitors THANK YOU FOR CHOOSING AN NEC © MultiSync MONITOR — Important — To help us in our continuing efforts to better serve and support you, and to bring you new and innovative products, please take a few moments to register your new NEC MultiSync monitor. By returning this card, we confirm your date of purchase and records the model and serial numbers. This facilitates our ability to process warranty claims, especially if your original proof of purchase is lost. Thank y
Résumé du contenu de la page N° 5
Quick Start ® To attach the MultiSync FP Series monitor to your system, follow these instructions: 1. Turn off the power to your computer. If you are using the signal cable, continue to Step 2. If you are using a BNC cable, please skip to Step 3. NOTE: BNC cables may be purchased at your local electronics store. 2. For the PC: Connect one end of the 15-pin mini D-SUB signal cable to the connector of the display card in your system (Figure A.1) and the other end to the back of the monitor (Figure
Résumé du contenu de la page N° 6
Quick Start cont.Start ® 4. Connect one end of the power cord to the MultiSync FP Series monitor and the other end to the power outlet (Figure D.1). 5. Turn on the monitor (Figure E.1) and the computer. 6. The Factory Setting for your monitor is set for D-SUB installation. If you are using a BNC cable connection, push the BNC/D-SUB button on the front of the monitor (Figure E.1) to switch settings. Figure A.2 Figure B.2 R G(/Sync) B HS/CS VS Power Outlet BNC Connector Power Cord Figure D.1 Figu
Résumé du contenu de la page N° 7
Quick Start cont.Start ® If your computer is equipped with USB and uses the Windows 98 operating system and you want to operate the monitor’s user controls using your system, you can install USB support by using the following procedure. To attach the USB port on your MultiSync FP Series monitor to a USB port on your system: 1. Using the supplied USB cable, connect the USB Series B connector end to the USB upstream port on the monitor (Figure 1). 2. Connect the other end of the supplied cable to
Résumé du contenu de la page N° 8
Controls ™ OSM (On-Screen Manager) control buttons on the front of the monitor function as follows: Main Menu Sub-Menu EXIT Exits the OSM menu. Exits to the OSM controls main menu. / Moves the highlighted Moves the highlighted area area up/down to select up/down to select one of the one of the controls. controls. –/+ Moves the highlighted Moves the bar in the – or + area left/right to select direction to decrease or one of the controls. increase the adjustment. PROCEED Has no function. Only
Résumé du contenu de la page N° 9
Controls cont.Start ® Color Control/AccuColor Control System Color presets 1 through 5 selects the desired color setting. The bar is replaced by the color setting choice from 1 to 5. Each color setting is adjusted at the factory to the stated Kelvin. If a setting is adjusted, the name of the setting will change from Kelvin to Custom. Red, Green, Blue: NEC’s AccuColor Control System decreases or increases the monitor’s red, green or blue color guns depending upon which is selected. The change
Résumé du contenu de la page N° 10
Controls cont. Linearity: This selection allows you to adjust the spacing of the area on the screen. The purpose of this control is to ensure that a one-inch circle is a true one-inch circle wherever it is on the screen. The best way to determine the vertical linearity is as follows: • Draw equally spaced horizontal lines using a drawing application that has a ruler. • Use the Vertical Balance control to adjust the lines near the top and bottom of your screen. • Use the Vertical control to adjus
Résumé du contenu de la page N° 11
Controls cont. ™ IPM System Off Mode: Enable: The IPM System works normally and all stages of energy savings are utilized. Disable: The Off Mode of the IPM System is not used. NOTE: For standard systems and graphics boards, keep the factory setting at ENABLE. ™ EdgeLock Control: Operating your monitor at a non-standard timing may cause images to appear darker than normal or have color distortion. Use of the EdgeLock control will adjust images to their normal state. Refresh Notifier: A message w
Résumé du contenu de la page N° 12
Recommended Use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING ® THE MULTISYNC FP Series COLOR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel. • Do not spill any liquids into the cabinet or use your monitor near water. • Do not insert objects of any kind into the
Résumé du contenu de la page N° 13
Recommended Use cont. CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen. • Position your monitor no closer than 12 inches and no further away than 28 inches from your eyes. The optimal distance is 24 inches. • Rest your eyes periodicall
Résumé du contenu de la page N° 14
Specifications ® ™ Monitor MultiSync FP950 Notes Specifications Monitor Picture Tube Diagonal: 49.5 cm/19 inch 90° deflection, 0.25 - 0.27 mm (variable) Viewable Image Size: 45.8 cm/18 inch grille pitch, medium short persistence Radius: 57800 mm phosphor, aperture grille CRT, multi-layered, anti-static screen coating, semi-dark-tint ® screen, and OptiClear screen surface. Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms Sync: Separate sync. TTL Level Horizontal sync. Positive/Negative Vertical sync.
Résumé du contenu de la page N° 15
Specifications cont. ® ™ Monitor MultiSync FP1350 Notes Specifications Monitor Picture Tube Diagonal: 55.3 cm/22 inch 90° deflection, 0.25 - 0.27 mm (variable) Viewable Image Size: 50.8 cm/20 inch grille pitch, medium short persistence Radius: 57800 mm phosphor, aperture grille CRT, multi-layered, anti-static screen coating, semi-dark-tint ® screen, and OptiClear screen surface. Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms Sync: Separate sync. TTL Level Horizontal sync. Positive/Negative Vertical
Résumé du contenu de la page N° 16
Features Flat Aperture Grille CRT: Delivers an unparalleled viewing experience with a virtually flat image, eliminating distortion and reducing glare so that what you see on-screen is what you get on your printed output. The striped phosphor alignment of the CRT delivers superior vertical definition with improved brightness for more uniform image contrast. ® OptiClear Screen Surface: Reduces reflection and glare and increases contrast without sacrificing focus level, clarity or brightness. Dual
Résumé du contenu de la page N° 17
Troubleshooting No picture • Display card should be completely seated in its slot. • Power Button and computer power switch should be in the ON position. • Signal cable should be completely connected to display card/computer. • Check connector for bent or pushed-in pins. • Check that the BNC/D-SUB button is in the correct position. Image is scrolling or unstable • Signal cable should be completely attached to the computer. • Check pin assignments and signal timings of the monitor and your displa
Résumé du contenu de la page N° 18
References • BBS (978) 742-8706 NEC Technologies’ Remote Bulletin Board System is an electronic service accessible with your system and a modem. Communication parameters are: 300/1200/2400/9600/14.4k/28.8k bps, no parity, 8-data bits, 1 stop bit • Customer Service/ Technical Support (800) 632-4662 Fax (978) 742-7049 • Electronic Channels: Internet e-mail: tech-support@nectech.com Internet ftp site: ftp.nectech.com World Wide Web: http://www.nectech.com ® Windows 95/98 INF File: http://www.ne
Résumé du contenu de la page N° 19
Limited Warranty NEC Technologies, Inc. (hereinafter “NECTECH”), warrants this Product to be free from defects in material and workmanship and, subject to the conditions set forth below, agrees to repair or replace (at NECTECH’s sole option) any part of the enclosed unit which proves defective for a period of three (3) years from the date of first consumer purchase. Spare parts are warranted for ninety (90) days. Replacement parts or units may be new or refurbished and will meet specifications o
Résumé du contenu de la page N° 20
TCO’99 Congratulations! You have just purchased a TCO’99 approved and labeled product! Your choice has provided you with a product devel- oped for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products. Why do we have environmentally labelled computers? In many countries, environmental labelling has become an established method for encourag- ing the adaptation of goods and
