Résumé du contenu de la page N° 1
MultiSync LCD1550V
User’s Manual
Résumé du contenu de la page N° 2
WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION RISK OF ELECTRIC SHOCK • DO NOT OPEN TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REF
Résumé du contenu de la page N° 3
Declaration Declaration of the Manufacturer We hereby certify that the colour monitor MultiSync LCD1550V (LA-15R02) is in compliance with Council Directive 73/23/EEC: – EN 60950 Council Directive 89/336/EEC: – EN 55022 – EN 61000-3-2 – EN 61000-3-3 – EN 55024 and marked with NEC-Mitsubishi Electric Visual Systems, Corp. MS Shibaura Bldg., 13-23, Shibaura 4-chome, Minato-Ku, Tokyo 108-0023, Japan Power consumption of the monitor is less than 3W when in power-saving mode. English-2
Résumé du contenu de la page N° 4
For the Customer to use in U.S.A. or Canada Canadian Department of Communications Compliance Statement DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouiller du Canada. C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CSA C22.2 #950. Ce produit porte la marque ‘C-UL’ et se conforme au
Résumé du contenu de la page N° 5
2. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interferenc
Résumé du contenu de la page N° 6
Contents Your new NEC MultiSync LCD monitor box* should contain the following: • MultiSync LCD1550V monitor with tilt base • Power Cord(s) • Video Signal Cable • User’s Manual • CD ROM (includes complete User’s Manual in PDF format). To see the User’s Manual, Acrobat Reader 4.0 must be installed on your PC. * Remember to save your original box and packing material to transport or ship the monitor. English-5 1550V English
Résumé du contenu de la page N° 7
Quick Start To attach the MultiSync LCD monitor to your system, follow these instructions: 1. Turn off the power to your computer. 2. Remove connector cover and cable cover. 3. For PC: Connect the 15-pin mini D-SUB of the appropriate signal cable to the connector for the display card in your system (Figure A.1). Tighten all screws. For Mac: Connect the MultiSync LCD1550V Macintosh cable adapter to the computer (Figure B.1). Attach the 15-pin mini D-SUB end of the appropriate signal cable to the
Résumé du contenu de la page N° 8
Refer to the Controls section of this User’s Manual for a full description of these OSM controls. NOTE: If you have any problems, please refer to the Troubleshooting section of this User’s Manual. Figure A.1 Macintosh Cable Adapter (not included) Macintosh G3 and G4 do not need a Macintosh cable adapter Figure B.1 English-7 English
Résumé du contenu de la page N° 9
Connector cover Cable cover Clip B Figure C.1 Power Button Vacation Switch Figure D.1 Tilt Grasp both sides of the monitor screen with your hands and adjust the tilt as desired (Figure TS.1). Remove Monitor Stand for Mounting To prepare the monitor for alternate mounting purposes: 1. Remove the connector cover and cable cover (Figure R.1). 2. Disconnect all cables. 3. Place monitor face down on a non-abrasive surface (Figure R.2). English-8 1550V
Résumé du contenu de la page N° 10
4. Remove the 4 screws connecting the monitor to the stand and lift off the stand assembly (Figure R.2) the monitor is now ready for mounting in an alternate manner. 5. Connect the AC cord and signal cable to the back of the monitor (Figure R.3). 6. Reverse this process to reattach stand. NOTE: Use only VESA-compatible alternative mounting method. Figure TS.1 Figure R.1 English-9 English
Résumé du contenu de la page N° 11
Non-abrasive Figure R.2 surface Figure R.3 7. This LCD monitor is designed for use with a flexible arm. Please use the attached screws (4pcs) when mounting. To meet the safety requirements the monitor must be mounted to an arm which guaranties the necessary stability under consideration of the weight of the monitor. The LCD monitor shall only be used with an approved arm (e.g. GS mark). English-10
Résumé du contenu de la page N° 12
Replace screws Thickness of bracket (arm) 2.0 ~ 3.2 mm Tighten all screws 75 mm 75 mm 4 SCREWS (M4) (MAX depth: 8.5 mm) If use other screw, check depth of hole. Weight of LCD assembly: 3.2kg (MAX) English-11 English
Résumé du contenu de la page N° 13
Controls OSM (On-Screen-Manager) Controls The OSM controls on the front of the monitor function as follows: To access OSM press any of the control buttons ( , , -, +, NEXT). Control Menu EXIT Exits the OSM controls. Exits to the OSM main menu. Moves the highlighted area left/right to select control CONTROL / menus. Moves the highlighted area up/down to select one of the controls. ADJUST -/+ Moves the bar left/right to increase or decrease the adjustment. Activates Auto Adjust function. Enter the
Résumé du contenu de la page N° 14
Auto Adjust Automatically adjusts the Image Position, the H. Size and Fine setting. Position Controls LEFT/RIGHT Controls Horizontal Image Position within the display area of the LCD. DOWN/UP Controls Vertical Image Position within the display area of the LCD. H. SIZE Adjusts the horizontal size by increasing or decreasing this setting. FINE Improves focus, clarity and image stability by increasing or decreasing this setting. Colour Control Systems Five colour presets select the desired colour s
Résumé du contenu de la page N° 15
OSM TURN OFF The OSM control menu will stay on as long as it is use. In the OSM Turn Off submenu, you can select how long the monitor waits after the last touch of a button to shut off the OSM control menu. The preset choices are 10, 20, 30, 45, 60 and 120 seconds. OSM LOCK OUT This control completely locks out access to all OSM control functions. When attempting to activate OSM controls while in the Lock Out mode, a screen will appear indicating the OSM controls are locked out. To activate the
Résumé du contenu de la page N° 16
OSM Warning OSM Warning menus disappear with Exit button. NO SIGNAL: This function gives a warning when there is no signal present. After power is turned on or when there is a change of input signal or video is inactive, the No Signal window will appear. RESOLUTION NOTIFIER: This function gives a warning of use with optimized resolution. After power is turned on or when there is a change of input signal or the video signal doesn’t have proper resolution, the Resolution Notifier window will open.
Résumé du contenu de la page N° 17
Recommended Use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE MULTISYNC LCD COLOUR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel. • Do not spill any liquids into the cabinet or use your monitor near water. • Do not insert objects of any kind into the cabine
Résumé du contenu de la page N° 18
• Allow adequate ventilation around the monitor so that heat can properly dissipate. Do not block ventilated openings or place the monitor near a radiator or other heat sources. Do not put anything on top of monitor. CAUTION • The power cable connector is the primary means of detaching the system from the power supply. The monitor should be installed close to a power outlet which is easily accessible. • Handle with care when transporting. Save packaging for transporting. CORRECT PLACEMENT AND AD
Résumé du contenu de la page N° 19
• Avoid displaying fixed patterns on the monitor for long periods of time to avoid image persistence (after-image effects). • Get regular eye checkups. Ergonomics To realize the maximum ergonomics benefits, we recommend the following: • Use the preset Size and Position controls with standard signals. • Use the preset Colour Setting. • Use non-interlaced signals with a vertical refresh rate between 60-75 Hz. • Do not use primary colour blue on a dark background, as it is difficult to see and may
Résumé du contenu de la page N° 20
Specifications Monitor Specifications Notes MultiSync LCD1550V Monitor LCD Module Diagonal: Active matrix; thin film 38 cm/15 inches transistor (TFT) liquid Viewable Image Size: 38 cm/15 inches crystal display (LCD); Native Resolution (Pixel Count): 1024 x 768 0.30 mm dot pitch; 2 200cd/m white luminence, typical; 300:1 contrast ratio, typical. Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms Sync: Separate sync.TTL Level Horizontal sync. Positive/Negative Vertical sync. Positive/Negative Display Col
