Résumé du contenu de la page N° 1
User’s Manual
Manuel de l’utilisateur
Manual del Usuario
MultiSync LCD2470WNX
MultiSync LCD2470WVX
Résumé du contenu de la page N° 2
Index Warning ................................................................................................................................................................ 1 C ont ent s ...............................................................................................................................................................2 Display Setup ........................................................................................................................................
Résumé du contenu de la page N° 3
WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNI
Résumé du contenu de la page N° 4
Contents ® Your new NEC MultiSync LCD monitor box* should contain the following: • MultiSync LCD monitor with height adjustable stand • Power Cord • Cable Management Cover • Video Signal Cable (mini D-SUB 15 pin to mini D-SUB 15 pin) • Video Signal Cable (DVI-D to DVI-D) • USB Cable (LCD2470WNX) • User’s Manual Power Cord Cable Management Cover Mini D-SUB Cable USB Cable DVI-D Cable (LCD2470WNX) User’s Manual Manuel de l’utilisateur Manual del Usuario MultiSync LCD2470WNX MultiSync LCD
Résumé du contenu de la page N° 5
Display Setup ® To attach the MultiSync LCD monitor to your system: 1. Turn off the power to your computer. 2. For the PC or MAC with DVI digital output : Connect the DVI signal cable to the connector of the display card in your system (Figure 1). Tighten all screws. For the PC with Analog output: Connect the 15-pin mini D-SUB signal cable to the connector of the display card in your system (Figure 2). Tighten all screws. For MAC setup: Connect the Macintosh cable adapter to the computer, t
Résumé du contenu de la page N° 6
Display Setup - continued 3. Lift the connector cover off as shown (Figure 4). 4. Raise the LCD to the highest position (Figure 5). 5. Tilt the monitor backwards 30 degrees (Figure 6). 6. With the monitor tilted, pivot the screen 90 degrees as shown (Figure 7). NOTE: The monitor cannot pivot properly if the stand is not ex- tended fully and if it is not fully tilted. Damage to the monitor may occur if the monitor is pivoted without being positioned properly. Figure 4 Figure 5 (Pictured: LCD24
Résumé du contenu de la page N° 7
Display Setup - continued 7. Connect all cables to the appropriate connectors (Figure 8). Using the USB cable, connect the B type connector to the USB upstream port on the right side of the monitor and the A type con- nector to the downstream port on the computer. If you can use the cord from the USB device, use one of the downstream ports on the side of the monitor. (Figure 9). USB cable is used with WNX models only. VGA DVI-D DC-OUT* (LCD2470WNX only) AC-IN * NEC optional product attachm
Résumé du contenu de la page N° 8
Display Setup - continued 11. Hold all cables fi rmly against the stand. Place the cable cover back onto the stand (Figure 13). 12. Connect the power cord to the power outlet (Figure 14). NOTE: If using this monitor at AC125-240V, please refer to Recommended Use section of this manual for proper selection of power cord. 13. Turn on the monitor using the front power button and turn on the computer. 14. Analog input only: No-Touch Auto Adjust automatically adjusts the monitor to optimal set
Résumé du contenu de la page N° 9
Display Setup - continued Raise and Lower Monitor Screen The monitor may be raised or lowered. To raise or lower screen, place hands on each side of the monitor and lift or lower to the desired height (Figure RL.1). NOTE: Handle with care when raising or lowering the monitor screen. Figure RL.1 Screen Pivot Before pivoting, the screen must be raised to the highest level to avoid accidentally damaging the screen and to avoid pinching fi ngers. To raise the screen, place hands on each side of
Résumé du contenu de la page N° 10
Mounting Remove Monitor Stand for Mounting To prepare the monitor for alternate mounting method: 1. Place hands on each side of the monitor and lift up to the highest position. Remove the cable cover (Figure M.1). Remove the connector cover (Figure M.2). NOTE: If you have diffi culty removing the cable cover, push the the cover up (towards the top of the monitor) in order to unhook the cover from the stand, then remove, as shown in (Figure). Handle with care when Figure removing cable cove
Résumé du contenu de la page N° 11
Flexible Arm Installation This LCD monitor is designed for use with a fl exible arm. To mount the monitor to a fl exible arm: 1. Follow the instructions on how to Remove Monitor Stand for Mounting to remove the stand. 2. Use the 4 screws to attach the arm to the monitor (Figure F.1). NOTE: The LCD monitor should only be used with an approved arm (e.g. GS mark). To meet the safety requirements, the monitor must be mounted to an arm which guaranties the necessary stability under consideration
Résumé du contenu de la page N° 12
Controls ® OSD (On-Screen Display) control buttons on the front of the monitor func- tion as follows: To access OSD menu, press any of the control buttons (MENU/EXIT, Left, Right, Down, Up). To change signal input, press the SELECT button. NOTE: OSD must be closed in order to change signal input. Button Menu MENU/EXIT Exits the OSD controls. Returns to the OSD main menu. Left/Right Moves the highlighted area left/right to select control menus. Moves the bar left/right to increase or decrease th
Résumé du contenu de la page N° 13
Controls - continued DOWN / UP Controls Vertical Image Position within the display area of the LCD. H.SIZE Adjust this setting to increase or decrease the horizontal size. FINE Adjust this setting to improve focus, clarity, and image stability. ® AccuColor Control Systems ® AccuColor Control Systems: Six color presets select the desired color setting (sRGB and NATIVE color presets are standard and cannot be changed). R,G,B: Increases or decreases Red, Green or Blue color depending upon
Résumé du contenu de la page N° 14
Controls - continued DDC/CI: Tuns on or off the two-way communication between the graphics card and the monitor. With DDC/CI turned on, some monitor settings can be adjusted through the graphics card using a computer. FACTORY PRESET: Selecting Factory Preset allows you to reset all OSD control set- tings back to the factory settings. The RESET button will need to be held down for several seconds to take effect. Individual settings can be reset by highlighting the control to be reset and pr
Résumé du contenu de la page N° 15
Recommended Use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING ® THE MULTISYNC LCD COLOR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualifi ed service personnel. • Do not spill any liquids into the cabinet or use your monitor near water. • Do not insert objects of any kind into the ca
Résumé du contenu de la page N° 16
Recommended Use - continued CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for warm-up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen. • Position your monitor no closer than 16 inches and no further away than 28 inches from your eye
Résumé du contenu de la page N° 17
Specifi cations ® Monitor Specifications MultiSync LCD2470WNX Notes LCD Module Diagonal : 24.0 inch Active matrix; thin film transistor (TFT) liquid Viewable Image Size : 24.0 inch crystal display (LCD); 0.270 mm dot pitch; 2 Native Resolution 500cd/m white luminence; 1000:1 contrast (Pixel Count) : 1920 x1200 ratio, typical Input Signal ANALOG Video : 0.7 Vp-p/75 Ohms Sync : Separate sync. TTL Level Positive/Negative Composite sync. TTL Level Positive/Negative Composite Sync on Green (0.3Vp-p neg
Résumé du contenu de la page N° 18
Specifi cations ® Monitor Specifi cations MultiSync LCD2470WVX Notes LCD Module Diagonal : 24.0 inch Active matrix; thin fi lm transistor (TFT) liquid Viewable Image Size : 24.0 inch crystal display (LCD); 0.270 mm dot pitch; 2 Native Resolution 400cd/m white luminence; 1000:1 contrast (Pixel Count) : 1920 x1200 ratio, typical Input Signal ANALOG Video : 0.7 Vp-p/75 Ohms Sync : Separate sync. TTL Level Positive/Negative Composite sync. TTL Level Positive/Negative Composite Sync on Green (0.3V
Résumé du contenu de la page N° 19
Features Thin-frame design creates more desktop space for you to work and play, while the fl at screen’s crisp, bright images and crystal-clear text deliver a comfortable viewing experience. No Touch Auto Adjust™ automatically adjusts your optimal image settings upon initial power-on. ® AccuColor Control System allows you to change between six color settings on your display to match your personal preference. ® Redesigned OSD controls allow you to quickly and easily adjust all elements of you
Résumé du contenu de la page N° 20
Troubleshooting No picture • The signal cable should be completely connected to the display card/computer. • The display card should be completely seated in its slot. • Front Power Switch and computer power switch should be in the ON position. • Check to make sure that a supported mode has been selected on the display card or system being used. (Please consult display card or system manual to change graphics mode.) • Check the monitor and your display card with respect to compatibility and rec
