Résumé du contenu de la page N° 1
Public Signage Solutions
EN
User Manual
2010© Koninklijke Philips Electronics N.V. All rights reserved.
Philips and the Philips Shield Emblem are registered trade marks
of Koninklijke Philips Electronics N.V and are used under license
BDL3215E
from Koninklijke Philips Electronics N.V.
BDL4225E
Résumé du contenu de la page N° 2
Résumé du contenu de la page N° 3
TABLE OF CONTENTS SAFETY INSTRUCTIONS ..................................................................................................................................................................................................................... 1 Content s ............................................................................................................................................................................................................................................
Résumé du contenu de la page N° 4
User Manual BDL3215E / BDL4225E SAFETY INSTRUCTIONS WARNINGS AND PRECAUTIONS KNOW THESE SAFETY SYMBOLS CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact with any inside part of this product. This symbol alerts you that important literature concerning operation and maintenance has been incl
Résumé du contenu de la page N° 5
User Manual BDL3215E / BDL4225E REGULATORY INFORMATION CE DECLARATION OF CONFORMITY MMD declare under our responsibility that the product is in conformity with the following standards. EN61000-3-2:2006 (Limits for Harmonic Current Emission) EN61000-3-3:1995+A1:2001+A2:2005 (Limitation of Voltage Fluctuation and Flicker) following provisions of directives applicable. 2006/95/EC (Low Voltage Directive) 2004/108/EC (EMC Directive) 93/68/EEC (Amendment of EMC and Low Vol
Résumé du contenu de la page N° 6
User Manual BDL3215E / BDL4225E POLISH CENTER FOR TESTING AND CERTIFICATION NOTICE The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer, monitor, printer, and so on) should have the same power supply source. The phasing conductor of the room’s electrical installation should have a reserve short-circuit protection device in the form of a fuse with a nominal value no larger than 16 amperes (A). To com
Résumé du contenu de la page N° 7
User Manual BDL3215E / BDL4225E INFORMATION FOR UK ONLY WARNING - THIS APPLIANCE MUST BE EARTHED. Important: (B) This apparatus is supplied with an approved moulded 13A plug. To change a fuse in this type of plug proceed as follows: (A) 1.Remove fuse cover and fuse. 2.Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved type. 3.Refit the fuse cover. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate 3-pin plug fitted in its place. If
Résumé du contenu de la page N° 8
User Manual BDL3215E / BDL4225E ( Pb ) ( Hg ) ( Cd ) (Cr 6+ ) ( PBB ) ( PBDE ) SJ/T11363-2006 SJ/T11363-2006 10 5
Résumé du contenu de la page N° 9
User Manual BDL3215E / BDL4225E NORTH EUROPE (NORDIC COUNTRIES) INFORMATION Placering/Ventilation VARNING: FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS. Placering/Ventilation ADVARSEL: SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE. Paikka/Ilmankierto VAROITUS: SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA. Plassering/Ventilasjon ADVARSEL: NÅR DETTE UTSTYRET PLAS
Résumé du contenu de la page N° 10
User Manual BDL3215E / BDL4225E * The following components are prepared as options. Contents Table stand BDL3215E/BDL4225E monitor pack* should include: Main switch cover LCD monitor Screw for Main Switch cover x 2 Power cord (1.8 m) BNC TO RCA adapter x 5 VGA Signal Cable (1.8 m) Logo guider User Manual Remote Control and AAA Batteries POWER Quick installation guide. VIDEO AUDIO SMART SOURCE SOURCE PIP ON/OFF INPUT CHANGE CONTRAST BRIGHTNESS DISPLAY MENU SET AUTO EXIT ADJUST VOL UP M
Résumé du contenu de la page N° 11
User Manual BDL3215E / BDL4225E Elements Name and Functions Control Panel f e d c b a g h a POWER button (B): To switch the power on/off. b CH (+) button: To move the highlight bar up to adjust the selected item while OSD menu is on. c CH (-) button: To move the highlight bar down to adjust the selected item while OSD menu is on. d MENU button: To return to previous menu while OSD menu is on or to activate the OSD menu when the OSD menu is off. e VOL (+) button: To increase the adjustment wh
Résumé du contenu de la page N° 12
User Manual BDL3215E / BDL4225E Terminal Panel 11 (OUT) (OUT) (IN) (IN) 1 2 3 4 5 6 7 8 9 10 a AC IN connector h VGA IN (mini D-sub 15 pin) Connect the supplied power cord to the wall outlet. To input analog RGB signals from a computer or from other RGB equipment. b AUDIO OUT i DVI-D INPUT To output the audio signal from AUDIO IN 1, 2, or 3 jack to an external device (Stereo receiver, amplifier, etc.). To input digital RGB signals from a computer or other HDTV device with digital RGB output
Résumé du contenu de la page N° 13
User Manual BDL3215E / BDL4225E d CONTRAST button Remote Control To start CONTRACT OSD selection, and then press “+” or “-” button to adjust the value. e DISPLAY button POWER 1 To turn on/off the setting information displayed on the right- 10 up corner of the screen. VIDEO AUDIO f “-” button SMART SOURCE SOURCE To decrease the adjustment with OSD menu. 2 11 To move the sub-picture left when in “PIP” mode. 12 g SET button PIP To activate the setting with OSD menu. 3 ON/OFF INPUT CHANGE h AU
Résumé du contenu de la page N° 14
User Manual BDL3215E / BDL4225E Operating Range for the Remote Handling the remote control Control Do not subject to strong shock. Use the remote control by pointing it towards the remote control sensor on the LCD monitor. control. If the remote control gets wet, wipe it dry Use the remote control unit within a distance of about 7 m/23 ft immediately. from the front of the remote control sensor on the LCD monitor and within horizontal and vertical angle 3
Résumé du contenu de la page N° 15
User Manual BDL3215E / BDL4225E How to mount or attach table stand to the LCD Monitor Installs the LCD monitor in one of the following two ways: Way I: Attach and remove the table stand How to install table stand 1. Please turn the monitor off. 2. After inserting table stand in guide block, fasten the thumbscrews on both sides of the monitor. NOTE: Install the table stand with their longer portions directing to the front. Thumbscrews Longer portions directs to the front Table stand In the upri
Résumé du contenu de la page N° 16
User Manual BDL3215E / BDL4225E Way II: Mount the monitor on the wall Before mounting the monitor to the wall, make sure that the system has been power-off and you have obtain a standard wall-mounting kit (commercially available). Using mounting interface that comply with TÜV-GS and/or UL1678 standard in North America is recommended. 100 100 100 100 Protective Sheet 100 100 Table Tabletop stand 1. Lay a protective sheet on a table, which was wrapped around the monitor when it was packaged, bene
Résumé du contenu de la page N° 17
User Manual BDL3215E / BDL4225E Setup Procedure 3. Connect to external equipment 1. Install the system on the right location before making connections. CAUTION: Please refer to section “Connectivity” P.17~P.21 for operations. THE LCD MONITOR MUST BE MOVED OR INSTALLED BY TWO OR MORE PERSONS. (For 42” only) 4. Connect power cord Failure to follow this caution may result in injury if the LCD The power outlet socket should be installed as near to the moni
Résumé du contenu de la page N° 18
User Manual BDL3215E / BDL4225E 11.To prevent the main power switch from being changed To prevent the possibility of main power switch being carelessly pushed, please attach the main switch cover (accessory) onto it. NOTE: Remove main power switch cover to turn off the display. Screw Main switch cover 15
Résumé du contenu de la page N° 19
User Manual BDL3215E / BDL4225E Install the LCD Monitor in Portrait Mode BDL3215E/BDL4225E can be installed in portrait position, under the following conditions: Caution: Portrait mode is effective only when wall-mounted or ceiling-mounted. The table stand can not be used for the monitor in portrait position. Placing the monitor in portrait position, will shorten the average life of the LCD backlight. Operational Environment (Temperature) shall be limited, as shown below: Operational Temperatur
Résumé du contenu de la page N° 20
User Manual BDL3215E / BDL4225E Connectivity Before making connections: Connectivity Diagram BDL3215E / BDL4225E VCR Equipment with Digital interface DVD player Personal computer BDL3215E / BDL4225E HD or laser disk player (Second monitor) 17
