Résumé du contenu de la page N° 1
LCD Monitor
LCD Farbmonitor
Moniteur LCD
Monitor LCD
Monitor LCD
LL-T15A4
OPERATION MANUAL
BEDIENUNGSANLEITUNG
MODE D'EMPLOI
MANUALE D'USO
MANUAL DE FUNCIONAMIENTO
T15A4_cover1-2.p65 1 3/14/2003, 5:33 PM
Résumé du contenu de la page N° 2
Table of Contents/Inhaltsverzeichnis/Table des matières/Indice/Índice Notice for Users in Europe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Notice for Users in the UK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Notice for Users in Australia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Résumé du contenu de la page N° 3
Notice for Users in Europe This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by 93/68/EEC. Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit Änderung 93/68/EWG. Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées par la directive 93/68/CEE. Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23/EEG, gewijzigd door 93/68/ EEG. Dette udstyr overholder
Résumé du contenu de la page N° 4
Notice for Users in the UK FOR CUSTOMERS IN U.K. IMPORTANT The wires in this mains lead are coloured in accordance with the following code: GREEN-AND-YELLOW : Earth BLUE : Neutral BROWN : Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows: The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the safe
Résumé du contenu de la page N° 5
Notice for Users in the USA FCC Statement WARNING – FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Résumé du contenu de la page N° 6
TCO Development SE-114 94 Stockholm, Sweden Fax: +46 8 782 92 07 Email (Internet): development@tco.se Current information regarding TCO'99 approved and labelled products may also be obtained via the Internet, using the address: http://www.tco-info.com/ Congratulations! Environmental requirements You have just purchased a TCO'99 approved and labelled product! Your choice has provided you with a Flame retardants product developed for professional use. Your purchase Flame retardants are present in
Résumé du contenu de la page N° 7
Table of Contents Tips and safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Product description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Connecting the monitor and turning the monitor on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Connecting the monitor to a computer . . .
Résumé du contenu de la page N° 8
Tips and safety precautions - The TFT color LCD panel used in this monitor is The Power Cord made with the application of high precision - Do not damage the power cord nor place heavy technology. However, there may be minute points objects on it, stretch it or overly bend it. Also, do on the screen where pixels never light or are not add extension cords. Damage to the cord may permanently lit. Also, if the screen is viewed from result in fire or electric shock. an acute angle there may be uneven
Résumé du contenu de la page N° 9
Product description 12 7 8 9 10 11 6 1 2345 6 1. MENU button ............................ This button is used to pop-up, select and close the OSD (On Screen Display) Menu. 2. / MODE button ..................... When the OSD Menu is displayed: This button is used to select menu options. When the OSD Menu is not displayed: This button is used to set DISPLAY MODE. 3. buttons ............................. When the OSD Menu is displayed: These buttons are used to select an option or adjust the value
Résumé du contenu de la page N° 10
Product description Angle adjustment Standing up and adjusting the monitor Press down on the stand and adjust it to a suitable CAUTION! viewing angle. approx. 5° approx. 25° - Pressure from hands on the LCD panel could cause damage. - Be careful not to allow your fingers to be pinched. Standing up the monitor 1.Press down on the stand and lift up the top section of the monitor. - Do not use the monitor when tilted back beyond approximately 25º. The monitor may fall over leading to injury or mal
Résumé du contenu de la page N° 11
Connecting the monitor and turning the monitor on and off CAUTION! Connect the accessory audio cable When the accessory audio cable is connected to the - When connecting, ensure that both the monitor audio output terminal of the computer, the sound of and computer are switched off. the connected computer is output from the monitor - Be careful not to overly bend the cable or add speakers. You can also use the headphone jack of extension cords as this could lead to a the display. malfunction. Au
Résumé du contenu de la page N° 12
Connecting the monitor and turning the monitor on and off Connecting the monitor to a power source Installing set-up information and the ICC profile (for Windows) Depending on the type of computer or OS, you may Power terminal need to install the monitor set-up information on your system. If so, follow the steps below to install the monitor set-up information. (Depending on the type AC outlet of computer or OS, command names and methods may differ. Please follow the computer's own operation manu
Résumé du contenu de la page N° 13
Connecting the monitor and turning the monitor on and off For Windows 98 For Windows 2000 Installing monitor set-up information into Windows 98, Installing monitor set-up information into Windows and setting the monitor's ICC profile as a 2000, and setting the monitor's ICC profile as a predetermined value. predetermined value. This explanation assumes that the floppy disk drive This explanation assumes that the floppy disk drive is "A drive". is "A drive". If the "Add New Hardware Wizard" has
Résumé du contenu de la page N° 14
Connecting the monitor and turning the monitor on and off If the "Add New Hardware Wizard" has not Installing the ICC profile appeared: Installing the monitor's ICC profile. (If the set-up information has already been installed, so too has 1. Place the Utility Disk in the computer's A drive. the profile, and there is no need to install it.) 2. Click on the [Start] button. From [Settings], This explanation assumes that the floppy disk drive choose [Control Panel]. is "A drive". 3. Double click on
Résumé du contenu de la page N° 15
Connecting the monitor and turning the monitor on and off Information about the ColorSync profile (for MacOS) About the ColorSync profile ColorSync is Apple Computer's color management system and enables color reproduction characteristics to be realized when used with a compatible application. A ColorSync profile describes the color characteristics of the LCD monitor. Notes: - This monitor's ColorSync profile works with MacOS 8.5 or above. - When using the ColorSync profile, set [DISPLAY MODE] t
Résumé du contenu de la page N° 16
Adjusting the screen display and speaker volume Adjustment the backlight (right column) Adjustment lock function Brightness of backlight can be adjusted. By disabling the control buttons (i.e. setting the lock) any attempted changes to adjusted values Speaker volume adjustment (p.17) will be voided. Speaker volume can be adjusted. 1. Turn off the monitor power. 2.While pressing the MENU button, press the DISPLAY MODE setting (p.17) power button (i.e. turn the power on). Color tone or brightness
Résumé du contenu de la page N° 17
Adjusting the screen display and speaker volume Adjusting the speaker volume Automatic screen adjustment 1. Without the OSD Menu being displayed, press the Options in the ADJUSTMENT Menu can be adjusted automatically (CLOCK, PHASE, H-POS, or the button. 2.Check that [VOLUME] is selected. V-POS). If it is not selected, press the / MODE button and select [VOLUME]. Note: - When setting up this monitor for the first time or VOLUME after having changed an aspect of the current BRIGHT system, perfo
Résumé du contenu de la page N° 18
Adjusting the screen display and speaker volume Adjusting the screen automatically Manual screen adjustment 1. Press the MENU button. Adjustments can be made using OSD (On Screen The ADJUSTMENT Menu will be displayed. Display) Menu provided. ADJUSTMENT MANUAL AUTO 1.Display an image that makes the entire screen CLOCK 127 very bright. If using Windows, you can open and PHASE 16 H-POS 200 use the Adjustment Pattern on the accompanying V-POS 29 Utility Disk. (p.17) 1024x768 V: 6 0Hz H : 4 8.4kHz 2.
Résumé du contenu de la page N° 19
Adjusting the screen display and speaker volume ADJUSTMENT Menu GAIN CONTROL Menu ADJUSTMENT GAIN CONTROL MANUAL AUTO MANUAL AUTO CLOCK 127 BLACK LEVEL 32 PHASE 16 CONTRAST 50 H-POS 200 V-POS 29 1024x768 1024x768 V: 6 0Hz H : 4 8.4kHz V: 6 0Hz H : 4 8.4kHz MANUAL: Individual menu options are manually MANUAL: Individual menu options are manually adjusted. adjusted. AUTO: Every menu option is automatically AUTO: Every menu option is automatically adjusted. adjusted using the Auto Gain Control* fun
Résumé du contenu de la page N° 20
Adjusting the screen display and speaker volume WHITE BALANCE Menu MODE SELECT Menu WHITE BALANCE MODE SELECT OSD H-POSITION COOL STD WARM USER OSD V-POSITION SCALING LOW HIGH R-CONTRAST COLORS 260K 16M G-CONTRAST LANGUAGE B-CONTRAST 1024x768 1024x768 V: 6 0Hz H : 4 8.4kHz V: 6 0Hz H : 4 8.4kHz Notes: Notes: - On settings other than [STD] not all gradations - Depending on the resolution of the input signal, can be displayed. To display all gradations, set even if menu options can be select
