Résumé du contenu de la page N° 1
@ BOSCH
INSTALLATION INSTRUCTION MANUAL
for
Bosch Electric Built-in Ceramic Cook-top
Models NKT 72 and NKT 92
MANUEL D'INSTALLATION
Surface de cuisson _lectrique en €_r.amique encastr_e
ModUles NKT 72 et NKT 92
BEFORE YOU BEGIN, READ THESE INSTRUCTIONS "COM-
PLETELY AND CAREFULLY.
VEUILLEZ LIRE ATTENTIVEMENT CE MANUEL AVANT DE
COMMENCER L'INSTALLATION.
r
IMPORTANT: Save these instructions for the local electrical inspector's use
INSTALLER: Please leave this manual with owner for future reference
Résumé du contenu de la page N° 2
Introduction Table of Contents 3 Tools You Will Need power 'Requirements Counter Preparation Steps for Installation Technical Data Preparing the Location 5 for 30" Cook-Top 6 for 36" Cook-Top 7 Attaching Fastening Rails 8 Placing the Cook-Top 9 Electrical Supply 10 Electrical Connections 11 Final Check List 12 Schematic Wiring Diagrams 14 Introduction Table des mati_res Les outils dont vous aurez besoin Sp6cifications _lectriques requises Preparation du comptoir I_tapes de l'installation 15 Donn
Résumé du contenu de la page N° 3
Introduction COUNTER PREPARATION Please read these instructions COMPLETELY Counter space must be provided for installation of AND CAREFULLY. They will save you time and your new cook-top. When choosing a location effort and help to ensure optimum cook-top consider the following IMPORTANT performance. Be sure to observe all WARNINGS. CONSIDERATIONS: • Cabinet storage space located above the These installation instructions are intended for use cook-top should be avoided, to eliminate the by a qual
Résumé du contenu de la page N° 4
Technical Data NKT 72 series, (30", 4 element) Dimensions, NK'F 72 a Height 4" 102 mm a • b Width 30" 762 mm c Depth 20U2" 521 mm Electrical Rating, NKT 72 Volts Hertz Amperes Watts 240 60 40 7 900 208 60 28 6 000 NKT 92 series, (36", 5 element) Dimensions, NKT 92 a Height 4" 102 mm b Width 36" 914 mm c Depth 201/_'' .. 521 mm a Electrical Rating, NKT 92 Volts Hertz A_l_res Watts 240 60 _ 9 900 74O0 208 60
Résumé du contenu de la page N° 5
Preparing the Location for 30", four Element Cook-Top 30"(762mm) rain cabinet width above cooktop For minimum depth cJearences see note* Lower cabinet depth: Openin >25 (635 ram) for box heightJ combinationwith _- / . rain downdraft fan ...._/2-1/2 (63.5mm) >24 (610 ram) without downdraft fan 2-1/4"(57mm) counter space both sides of cutout from a combustible Locate supply junction surface box on wall 12"(305mm) or more above the floor line • Note: 24" rain. clearance if bottom of wood Work top:
Résumé du contenu de la page N° 6
Preparing the Location for 36", five Element Cook-Top 36"(914mm) min above ccoktop cabinet width 13"(330mm)max upper cabinet depth For minimum clearenoes see note" 35-1/4"(895mm) width Lower cabinet depth: Burner box height >25"(635 mm) for combination with min downdraft fan. >24"(610 mm) without downdraft fan 2-1/4"(57mm) counter space both sides of cutout from a combustible Locatesupply junction surface box on wall 12"(305mm) or more above the floor line • Note: 24" min. clearance if bottom of
Résumé du contenu de la page N° 7
Attaching Fastening Rails used for both NKT 72 and NKT 92 series 90* To attach the fastening rails: I. Mark the center as shown in drawing. 2. Align rails using notch. 3. Secure the rails tightly using screws. Note: a. The top flange of rail must sit tightly against the counter top. b. If counter top is tiled, the lower screws holes in the rails should be Important: used. • Do all counter top preparation, before installing the cook-top. Be sure to clean area after cutting and before installing c
Résumé du contenu de la page N° 8
Placing the Cook-Top 1. Thread the cable through the cutout opening. 2. Gently place the cook-top into the cutout, taking care to assure that cable does not become pinched between the cook-top and the counter cutout, and press in place so that cook-top interlocks with rails. Note: If installing on a tiled counter top, seal the tile joints with silicone rubber. NKT 92 series shown SPECIAL NOTE: Do not install the cooktop over a refrigerator, dishwasher or washing roac!!he.
Résumé du contenu de la page N° 9
Electrical Supply WIRING REQUIREMENTS Before installing the cook-top have a qualified electrician verify that your home is provided with When making the wire connections, use the entire adequate electrical service and that the addition of length of the conduit provided (3 feet)• The conduit must not be cut. the cook-top will not overload the branch circuit on which it is to be installed. A separate three-wire or four-wire single phase, 240 or 208 Volt, 60 Hz, Before making connections make sure
Résumé du contenu de la page N° 10
J t -i Electrical Connections Cable from This appliance is manufactured with a green and power supply yellow striped GROUND wire connected to the Grounded neutral Junction box cook-top chassis. After making sure that the power has been turned off connect the flexible conduit Red wires from the cook-top to the junction box using a U.L. listed conduit connector, see figures A and B. Twist-on Figures A and B and the instructions provided connectors below present the most common way of connecting th
Résumé du contenu de la page N° 11
Final Check List To prevent improper connection leading to damage of electrical components and so voiding the warranty, the following steps must be performed: 1. Check the electrical requirements and make sure you have the correct electrical supply and that the cook-top is properly grounded. 2. Make sure all control knobs are in the off position. 3. Turn on the power supply to the cook-top. 4. Check power at jnnction box wires using a volt meter having a range of 0-250 VAC. The voltage reading b
Résumé du contenu de la page N° 12
Schematic Wiring Diagrams (7 NKT 72 series _rM i r"- * -- i ---:-] NKT 92 series t4_ t_ B te I i I _431 N2_ _ _,_ .L__ __1 _ i__iii I -,l!' 12
