Résumé du contenu de la page N° 1
<< Previous Next >>
Getting Your Multifunction
Back On Your Network
After A Router Or Network Change
PIXMA MG6320
Windows OS
1
Résumé du contenu de la page N° 2
Information << Previous Next >> Important If any of the following situations exist • You have replaced your Router or Access Point • You want to use a different wireless network • Router settings have been changed. Please complete the following steps to apply the new configuration settings to your multifunction. 2
Résumé du contenu de la page N° 3
Preparing to Connect My Multifunction << Previous Next >> To My Network Network Requirements Before connecting the machine to the network, make sure that configuration of the computer and access point or router is complete, and that the computer is connected to the network. Wireless Connection Before connecting the machine to the network, the computer needs to be connected to the network. Make sure that configuration of the computer and access point or rout
Résumé du contenu de la page N° 4
Preparing to Connect My Multifunction << Previous Next >> To My Network An "Ad-hoc connection," which establishes a direct connection to the computer over a wireless connection without using an access point, is not supported. A wireless access point or router is required to use your printer on a wireless LAN. Notes on Network Connection • The configuration, router functions, setup procedures and security settings of the networ
Résumé du contenu de la page N° 5
Installing the Drivers & Software << Previous Next >> Software Installation To use the machine by connecting it to a computer, software including the drivers needs to be copied (installed) to the computer's hard disk. The installation process takes about 20 minutes. (The installation time varies depending on the computer environment or the number of application software to be installed.) IMPORTANT • Log on as the administrator (or a member of the Administrators group).
Résumé du contenu de la page N° 6
Connecting to the Wireless Network << Previous Next >> Installing the PIXMA MG6320 on Your Wireless Network When you reinstall your printer on your network because of a router or network change, you follow the same procedure as for a first time install. A step-by-step walk through of the wireless setup is built in to the installation routine of the software that shipped with your PIXMA. Insert the Setup CD-ROM * that came with your printer into your CD-ROM drive and proc
Résumé du contenu de la page N° 7
Connecting to the Wireless Network << Previous Next >> Installing the PIXMA MG6320 on Your Wireless Network Continue to follow on-screen instructions. Be sure to select Wireless Connection on the Connection Method Selection screen (1-2). Continue to follow instructions until the Setup Procedure Selection screen (3-1)appears. This is shown on the next page 7
Résumé du contenu de la page N° 8
Connecting to the Wireless Network << Previous Next >> The printer automatically searches for access points that support WPS (Wi-Fi Protected Setup)*. *Unless you are absolutely sure your access point supports WPS and you are familiar with activating this on your access point, press the Stop button on the printer’s operation panel and click on Other Methods on the Setup Procedure Selection screen (screenshot shown below)*. If the Push Button Method is not shown on th
Résumé du contenu de la page N° 9
Connecting to the Wireless Network << Previous Next >> For Standard setup only Follow the instruction then click Next on the Connection via Standard setup (4-1) screen. Select Standard setup on the Setup Procedure Selection screen (3-2) Continue to next page before proceeding any further with setup 9
Résumé du contenu de la page N° 10
Connecting to the Wireless Network << Previous Next >> Follow On-screen instructions. When you get to Step 4-2 and later in Step 4-4 ( screens shown below) you will need to know SSID and password information* Step 4-4 Step 4-2 *Unless you are absolutely certain of this information, please continue to the next page for information on locating / verifying this information Continue to follow the on-screen instructions. Click Next when the Completion of Connection screen (
Résumé du contenu de la page N° 11
Connecting to the Wireless Network << Previous Next >> If you don't know your Access Point / Router name or SSID*, or the Passphrase or Network key for your wireless network, you can find this information during Standard setup using the Setup CD-ROM or the downloaded file (Mini Master Setup). *The terms 'SSID' and 'AccessPoint / Router' refer to a name used to identify the specific Access Point or Router. "Passphrase' and 'Network Key' refer to a password required to prevent
Résumé du contenu de la page N° 12
Installing the Drivers & Software << Previous Next >> Network setup is complete. Continue to follow any remaining On-screen instructions to install the software. On the Software Installation List screen, select any software to be installed. MP Drivers is required for the printer to be able to print and scan and cannot be de-selected. MY Image Garden and Quick Menu* are highly recommended to take full advantage of your printer’s features. *Note: If you are using the downloa
Résumé du contenu de la page N° 13
Installing the Drivers & Software << Previous Next >> Click Complete when the Setup Completion screen appears. Continue to follow any remaining on-screen instructions to finish and exit the setup program 13
Résumé du contenu de la page N° 14
Installing the Drivers & Software << Previous Installing the PIXMA MG6320 on Your Wireless Network If you can’t find your CD-ROM, you may download the MG6300 series Mini Master Setup, which includes the same step-by-step installation as the CD-ROM, by following the instructions below: 1. Click here to access the MG6320 Drivers & Software page. 2. Select the operating system and version of your computer (see example below). 3. Expand the ‘Drivers’ section, if necessary, by clicking
