Résumé du contenu de la page N° 1
Résumé du contenu de la page N° 2
Résumé du contenu de la page N° 3
CAL 3200 CAL 3200 4 5 6 7 3 8 2 2 9 1 10 100 90 80 70 60 50 40 30 20 10 )2SHUDWLRQDQG 0DLQWHQDQFH0DQXDO © 1998 GBC Pro-Tech Do not duplicate without written permission GBC Pro-Tech 4151 Anderson Road De Forest, Wisconsin 53532 Tel: 608-246-8844 Part Number 930-016 Fax: 608-246-8645 WARNING WARNING ACHTUNG MISE EN GARDE ACHTUNG MISE EN GARDE F-60™ PRO-TECH
Résumé du contenu de la page N° 4
F-60 Operation and Maintenance Manual The information in this publication is provided for reference and is believed to be accurate and complete. GBC Pro-Tech is not liable for errors in this publication or for incidental or consequential damage in connection with the furnishing or use of the information in this publication, including, but not limited to, any implied warranty of fitness or merchantabil- ity for any particular use. GBC Pro-Tech reserves the right to make changes to this publicatio
Résumé du contenu de la page N° 5
F-60 Operation and Maintenance Manual DEOH 7 R I RQW & HQWV 6HF WL RQ HW 6DI\ Caution/Warning Label Locations ................................................................................... 1-3 6HF WL RQ ,QV WDW OODLR Q Preinstallation Checklist ............................
Résumé du contenu de la page N° 6
F-60 Operation and Maintenance Manual Setup ..........................................................................................................................3-6 Procedure, Pass 1 ...................................................................................................... 3-6 Procedure, Pass 2 ...................................................................................................... 3-7 6HF WL RQ 0 DLQ WH QD QFH DQ G U R XE 7 OHV K RRW LQ J
Résumé du contenu de la page N° 7
1 / 4 F-60 Operation and Maintenance Manual The F-60 Laminator has been designed with safety as a HFW 6 LR Q 6DIHW\ primary consideration. However, you must become thoroughly familiar with the controls, proper operation, proper service procedures, and safety features of the DO NOT ATTEMPT TO OPERATE YOUR laminator before using or servicing the unit. ORCA-IV VINYL TRANSFER MACHINE UNTIL YOU HAVE READ THIS SECTION GBC Pro-Tech F-60 Laminator is a powerful machine CAREFULLY! that is des
Résumé du contenu de la page N° 8
POWER POWER Safety F-60 Operation and Maintenance Manual Reset Button WARNING Never place fingers or arms between the rolls when they are turning or when the rolls are in the closed position. You can be crushed or burned. WARNING Do not wear ties, loose fitting clothing or dangling jewelry while operating or servicing the laminator. These items can get caught in the nip and choke you or you can be crushed or burned. WARNING Do not operate the laminator near water. You can Figure 1-2: Re
Résumé du contenu de la page N° 9
F-60 Operation and Maintenance Manual CAUTION WARNING Use only 80% isopropyl alcohol or a rubber Do not attempt to move the laminator across cement eraser to clean the laminating rolls. anything other than a flat, level surface without Harsh chemicals like toluene, acetone or MEK trained and qualified riggers. You can be crushed destroy the silicone covering of the rolls. or seriously injured. The F-60 Laminator is a large and heavy piece of equipment. It is necessary to employ LICENSED RI
Résumé du contenu de la page N° 10
109 00 80 76 00 CAL 3200 54 00 30 21 00 CAL 3200 4 5 6 7 3 8 2 9 1 10 2 Safety F-60 Operation and Maintenance Manual (Inside cabinet) WARNING ACHTUNG MISE EN GARDE WARNING ACHTUNG MISE EN GARDE WARNING ACHTUNG MISE EN GARDE (Inside cabinet) ©1994 Hazard Communication Systems, Inc. 800-748-0241 WARNING ACHTUNG MISE EN GARDE Figure 1-4: Locations of Safety Labels 1-4 © GBC Pro-Tech 1998 July MISE EN GARDE MISE EN GARDE PRO-TECH WARNING ACHTUNG WARNING ACHTUNG F-60™
Résumé du contenu de la page N° 11
E C N E G R U ' D T E R R A P O T F-60 Operation and Maintenance Manual The following are typical safety hazard decals used on GBC Pro-Tech machines, with a brief description (“Mean- ing” column) of each decal. Decal Meaning Decal Meaning WARNING! WARNING! WARNING SAFETY Moving parts can INSTRUCTIONS 1. Read and understand the Operation Manual and ACHTUNG crush and cut. all safety labels before operating this machine. SICHERHEITS- MISE EN GARDE 2. Only a trained person is to be permitted to oper
Résumé du contenu de la page N° 12
Safety F-60 Operation and Maintenance Manual Blank page. 1-6 © GBC Pro-Tech 1998 July
Résumé du contenu de la page N° 13
F-60 Operation and Maintenance Manual Installation HFW 6 LR Q QVW , DOWLRQOD CAUTION GBC Pro-Tech is committed to a program of ongoing product improvement. As a result, we are providing Do not locate the laminator where air is blowing these instructions so that you can insure that your new directly on the machine. The air flow can cool the F-60 Laminator is properly and securely unpacked, rolls unevenly and result in poor quality output. moved and installed. Before a F-60 Laminator c
Résumé du contenu de la page N° 14
Installation F-60 Operation and Maintenance Manual Wall 4' x 6' (~1.22 m x 2 m) Work Table on Wheels Table Height 35-3/4" (~.94 - .95 m) 8'6-1/2" (~2.6 m) Electrical Supply 78" (~2 m) Rear 3' (~1 m) 20' 30" (~.6 m) (~.76 m) Front 4' x 6' (~1.22 m x 2 m) Work Table on Wheels Table Height 8'6-1/2" 35-3/4" (~2.6 m) (~.94 - .95 m) 13' (~4 m) Figure 2-1: Laminator Space Requirements 2-2 © GBC Pro-Tech 1998 July
Résumé du contenu de la page N° 15
R R U U D' D' T T E E ARR ARR OP OP ST ST CY CY N N E E 5 1 4 2 2 100 90 81 0 70 0 60 0 CAL 3 200 9 50 8 0 40 7 0 30 6 0 20 5 0 10 0 CAL 3 200 40 30 20 10 CAL 3 2C 00 AL 3 200 324 5 6 7 8 1 324 5 6 7 9 18 0 9 1 10 G G F-60 Operation and Maintenance Manual Installation 2. There are two hold down bridges that are con- 8Q SDNL FQJ nected to sides 4 and 5. Remove the hold down + NOTE bridges and then remove sides 4 and 5. ALL SHIPMENTS ARE EX- WORKS. At our dock title passes to the buyer. Please re
Résumé du contenu de la page N° 16
3 4 5 6 7 8 2 1 910 2 100 90 80 70 60 50 40 30 20 10 C A L 32 00 C A L 32 00 Installation F-60 Operation and Maintenance Manual 4. Carefully remove the accessory pack from the skid. 10. The ramps included with the laminator can be The accessory pack should contain: secured to the edge of the crate bottom using the screws left over from the crate disassembly (see 1 Set, hex wrenches Figure 2-2). 1 Slitting knife 11. Have the machine moved off the skid and placed 1 Manual on the floor by licen
Résumé du contenu de la page N° 17
F-60 Operation and Maintenance Manual Installation + A NOTE ABOUT RECYCLING HO Y LQJ /H The crate components can be reused for shipping the Tools required: machine again, or can be disassembled and the wood and screws recycled. The shrink wrap is not recyclable, • Adjustable wrench however, so it must be discarded. • Carpenter's level 14. Level the laminator using the procedure later in this section. To level the laminator: 1. Raise each end, remove the castors and install a 6HW XS leveling pa
Résumé du contenu de la page N° 18
Installation F-60 Operation and Maintenance Manual 6WD U WX S The first time the laminator is started and every time it WARNING is serviced you should use the following checklist to Use extreme caution when operating the machine confirm that the unit is operating properly and that all with the guard off. You can be crushed or safety mechanisms are functioning. burned. Startup Checklist o Is the motor functioning? Start the laminator and go through the following check- Test the motor at var
Résumé du contenu de la page N° 19
POWER 1 POWER / 4 F-60 Operation and Maintenance Manual Operation 6HFWLR Q 2SHU DWLR Q Reset Button H 6DIW\ The F-60 Laminator has been designed with safety as a primary consideration. However, you must become thoroughly familiar with the controls, proper operation, proper service procedures, and safety features of the laminator before using or servicing the unit. GBC Pro-Tech F-60 Laminator is a powerful machine that is designed to mount, laminate and encapsulate. The forces required
Résumé du contenu de la page N° 20
100 90 80 70 60 50 40 30 20 10 3 4 56 7 8 2 1 2 910 CA L 3200 CA L 3200 Operation F-60 Operation and Maintenance Manual 8. LOWER ROLL HEAT ON/OFF – Turns the 2S HU W RUD & QR UW RO V heater controller for the lower main roll on or off. The operator controls for the F-60 Laminator are 9. COOLING FAN ON/OFF – Turns the cooling fan located on the front and rear of the unit, to the right of on or off. the operator position. The names and functions of these controls are as follows: 10. POWER ON/
