ページ1に含まれる内容の要旨
GAS HOB
ZGL 62 ITX
INSTRUCTION BOOKLET
Please read this instruction booklet before using the appliance
GB IE
ページ2に含まれる内容の要旨
Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 727727 Installation This appliance must be installed and serviced by a Never leave the hob unattended when cooking with competent person as stated in the Gas Safety ( oil and fats. Installation and Use) Regulations Current Editions Never use plastic or aluminium foil dishes on the hob. and the IEE Wiring Regulations. Pe
ページ3に含まれる内容の要旨
Contents For the Installer For the User Instructions for the Installer 8 Important Safety Information 2 Installation 10 Description of the Hob 4 Electrical connections 12 Operation 5 Wiring Diagram 13 Maintenance and Cleaning 6 Something Not Working? 7 Fault Finding 13 Service and Spare Parts 7 Commissioning 15 Guarantee/Customer Service 16 Conversion from Natural Gas to LPG 15 European guarantee 17 Environmental Information Guide to Use the instructions After installation, please dispose of th
ページ4に含まれる内容の要旨
Description of the Hob 3 4 3 1 2 5 6 1. Hob Top 2. Auxiliary Burner 3. Semi-rapid Burners 4. Rapid Burner 5. Control knobs 6. Electric Ignition Push Button 4
ページ5に含まれる内容の要旨
Operation Hob burners To light a burner: push the electric ignition pushbutton which is marked by a little spark. at the same time turn the relevant control knob anticlockwise to maximum position and keep it pushed down about 5 seconds. This will allow the "thermocouple" (see diagram - letter D) to be heated and the safety device to be switched off, otherwise the gas supply would be interrupted. then, check the flame is regular and adjust it as required. If you cannot light the flame ev
ページ6に含まれる内容の要旨
Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob Top Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little washing up liquid has been added. Avoid the use of the following: - household detergent and bleaches; - impregnated pads unsuitable for n
ページ7に含まれる内容の要旨
Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Zanussi Service Force Centre. IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee. SYMPTOM SOLUTION There is no spark when lighting the gas Check that the unit is plugged in and the electrical supply is switched on Check that th
ページ8に含まれる内容の要旨
Instructions for the Installer Engineers technical data Overall dimensions Rear Left Burner (semi rapid) Heat Input 2.0 kW (6824 BTU/HR) Width: 580 mm Depth: 500 mm Front Left Burner (auxiliary) Heat Input 1.0 kW (3412 BTU/HR) Cut out dimensions Rear Right Burner (semi rapid) Width: 550 mm Heat Input 2.0 kW (6824 BTU/HR) Depth: 470 mm Front Right Burner (rapid) Supply connections Heat Input 3.0 kW (10236 BTU/HR) Gas: RC 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230 V 50 Hz supply
ページ9に含まれる内容の要旨
50 mm 100 mm 50 mm 100 mm 50 mm 50 mm 600 mm Important safety requirements This hob must be installed in accordance with the Gas Location Safety (Installation and Use) Regulations (Current Edition) The hob may be located in a kitchen, a kitchen/diner or and the IEE Wiring Regulations (Current Edition). bed sitting room, but not in a bathroom, shower room or For appliances installed in the Republic of Ireland please garage. refer to NSAI- Domestic Gas Installation I.S. 813 Current Before making t
ページ10に含まれる内容の要旨
Installation IMPORTANT: This hob must be installed by a competent person to the relevant Gas Standards. Please, ensure that, once the hob is installed, it is easily accessible for the engineer in the event of a breakdown. WHEN THE HOB IS FIRST INSTALLED Once the hob has been installed, it is important to remove any protective materials, which were put on in the factory. Any gas installation must be carried out by a competent person. The manufacturer will not accept liability, should the above i
ページ11に含まれる内容の要旨
Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it It is also recommended to carry out the electrical will be necessary to fit a heat resistant board below the connection to the hob as shown in diagrams 1 and 2. base of the hob on the underside of the work surface. 1 2 3 ON/OFF SWITCH ON/OFF SWITCH FLEX OUTLET FLEX OUTLET FO 0763 FO 0764 FO 1013 Dimensions are given in mm. Building over a kitchen unit with door Proper arrangements must be t
ページ12に含まれる内容の要旨
Electrical connections Any electrical work required to install this hob Permanent Connection should be carried out by a qualified electrician or In the case of a permanent connection, it is necessary competent person, in accordance with the current that you install a double pole switch between the hob regulations. and the electricity supply (mains), with a minimum gap of 3 mm. between the switch contacts and of a type THIS HOB MUST BE EARTHED. suitable for the required load in compliance with th
ページ13に含まれる内容の要旨
Wiring Diagram A. TAPS IGNITOR SWITCHES B. IGNITOR UNIT Fault Finding Preliminary Electrical Systems Check SOCKET PLUG (with cover removed) (face view) Earth Wire ( ) Green/Yellow ( ) E Brown Blue START Neutral Wire Isolate appliance Blue and carry out: A: Earth Continuity N L check. Blue Green Brown Yellow Carry out: Electricity supply NO YES Carry out: D: Resistance to should now be C: Polarity check. Earth check. satisfactory. A. EARTH CONTINUITY CHECK - Appliance must Has inlet fuse blo
ページ14に含まれる内容の要旨
Ignition System / Gas Ignition YES Check gas supply at Ignitor does not spark burner NO Check plug top fuse and Light burner manually replace if necessary Check by pass Check polarity and simmer earth continuity of supply point Check position of the Check earth continuity electrode of appliance Check continuity from the tip Check fitting of burners Check continuity from 'N' on the of each electrode to the mains connector block and "O" on terminals 1 to 4 on the ignitor the ignitor unit unit Chec
ページ15に含まれる内容の要旨
Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. - Turn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguished follow the procedure below. Procedure: - Re-ignite the burner and set to MIN. - Remove the control knob and use a thin bladed screwdriver to turn the ad
ページ16に含まれる内容の要旨
Guarantee/Customer Service Standard guarantee conditions We, Zanussi-Electrolux, undertake that if within 12 months of the date of the purchase this Zanussi-Electrolux appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: · The appliance has been correctly installed and used only on the electricity supply stated on the rating p
ページ17に含まれる内容の要旨
European guarantee This appliance is guaranteed by Electrolux in each of the countries listed at the back of this user manual, for the period specified in the appliance guarantee or otherwise by law. If you move from one of these countries to another of the countries listed below the appliance guarantee will move with you subject to the following qualifications: • The appliance guarantee starts from the date you first purchased the appliance which will be evidenced by production of a valid purch
ページ18に含まれる内容の要旨
18
ページ19に含まれる内容の要旨
19
ページ20に含まれる内容の要旨
www.zanussi-electrolux.co.uk 35687-8002 11/06 Grafiche MDM - Forlì
