ページ1に含まれる内容の要旨
2
User's Manual
for 25-Channel Caller ID/Call Waiting
Cordless Telephone 7710
Fold open this manual for information
about this telephone's installation and
operation. Please read Part 1 —
Important Product Information,
included in this package.
Part 2
© 1998 Philips Consumer Communications L.P. All rights reserved.
Printed in Mexico. Issue 1 AT&T
848233540
PAGE
NEW CALL
CHARGING/HANDSET IN USE
HANDSET LOCATOR
PWR RESERVE LOW BATT
ページ2に含まれる内容の要旨
INST ALLA TION Modular jack AC Adapter Power cord Telephone line cord 5 Connect the power cord. FOR TABLE/DESK INSTALLATION Plug the power cord into the jack labeled POWER on 1 Choose a spot near an electrical outlet and a the back of the base. Plug the AC adapter on the power telephone jack. cord into an electrical outlet. This phone requires a modular telephone jack and a 6 Charge the handset batteries before use. standard electrical outlet (110v AC). Place the handset face down or face up in
ページ3に含まれる内容の要旨
INST ALLA TION Remove the Wrap the line cord Feed the line cord Connect the line cord to the wall jack, and mounting bracket around the crescent- through the center mount the base on the wall. shaped tabs opening, and attach the base with the larger end toward the bottom underside of the wall-mounting bracket. (Make sure FOR WALL INSTALLATION you leave enough cord free to extend to the wall jack.) The wall-mounting bracket is a wedged, triangular plastic piece 6 Feed the free end of the line co
ページ4に含まれる内容の要旨
TELEPHONE OPERA TION Softkey Softkey Press the softkey to select the operation displayed on the bottom left or right of the screen. About Softkeys Handset Volume This telephone has been designed with your convenience in mind, of- The handset volume can be set to three different levels. Each fering you many features which you can access using the two “softkeys” time you press V the level changes. shown in the illustration. By pressing the softkey below the operation indicated on the display scr
ページ5に含まれる内容の要旨
TELEPHONE OPERA TION Antenna Softkey Softkey Message Waiting and Scroll through NEW CALL Light Access special screen information programming features HANDSET IN USE Light Scroll through Make or screen information CHARGING Light answer a call PAGE/HANDSET Dial number Reduce chance of LOCATOR Button displayed on screen call interception Access Handset charges face up or face down subscriber services Temporary Tone Put caller on m hold. (PHONE light flashes) Change channel Adjust handset volume Pa
ページ6に含まれる内容の要旨
TELEPHONE MEMOR Y Storing Numbers in Memory Dialing Memory Numbers 1 Make sure the PHONE light is off. 1 Press P. 2 Press . 2 Use the softkey to select MEM. MENU 3 Use the softkey to select DIRECTORY. 3 Enter the two-digit memory location. 4 Use the softkey to select ADD. Dialing M1 1 Press P. 2 Press m. 5 Enter the number you want to store (up to 16 digits). 6 Select DONE. Storing a Number Just Dialed 7 Follow the directions below to store a name — OR — in Telephone Memory Select DONE if you do
ページ7に含まれる内容の要旨
CALLER ID Number has been stored Voice mail message is Information missing or in telephone memory Voice Security waiting (if you subscribe incorrect (see In Case of Caller has called as Priority feature is active to this service) Difficulty) more than once Time call information was sent Battery power indicator Position of call in call history Date call information was sent Caller's telephone number Caller's name Scroll through call history About Caller Identification Message Waiting Indicator T
ページ8に含まれる内容の要旨
CALLER ID NOTE: If you try to use the Display Dial feature, but your call Call List Options cannot be completed unless you dial "1" before the number, You can customize how the phone stores call information. Select follow the steps below: whether the system stores information about ALL CALLS received, 1 Press + or - to locate the number you want to call. or for NO CALLS. The system comes set to ALL CALLS. MENU 2 Press . 1 Press MENU . 3 Use the softkey to select OPTIONS. 2 Use the softkey to
ページ9に含まれる内容の要旨
BA TTERIES Charging the Handset Battery Pack Replacing the Handset Battery Pack The batteries need charging when: 1 Remove the battery case cover on the handset by pressing • The phone beeps four times when you press P. on the indentation and sliding the cover downward. • The battery status icon on the screen is only partly 2 Lift out the old battery pack and unplug it from the handset. displayed. 3 Hold the new battery pack and plug the connector into • The phone does not respond when you press
ページ10に含まれる内容の要旨
OPERA TING RANGE This cordless telephone operates at the maximum power allowed Changing Channels by the Federal Communications Commission (FCC). Even so, the This cordless telephone has a an advanced 25-channel AutoSelect handset and base can communicate over only a certain distance — feature that minimizes the chance of interference. which can vary with the locations of the base and handset, the weather, and the construction of your home or office. In the unlikely event that you notice noise o
ページ11に含まれる内容の要旨
IN CASE OF DIFFICULTY If you have difficulty operating this phone, try the suggestions If you have no dial tone below. If you still have trouble, call 1 800 722-9125. Check all the previous suggestions. If you still do not hear a dial tone, disconnect the phone and try another phone in the If the phone does not work at all, same jack. If there is no dial tone on that phone either, the problem is probably in you wiring or local service. Call your check these items first local telephone servi
ページ12に含まれる内容の要旨
IN CASE OF DIFFICULTY If you hear noise in the handset The caller's name or phone number and the buttons don’t work is not displayed during Call Waiting The base unit and handset might not be set to the same security • Make sure you subscribe to combined Caller ID code. Place the handset in the base for at least 15 seconds to reset service with Call Waiting. the security code. • If you subscribe to the combined service, make sure you have this feature turned on (see "Call Waiting" in the CALLER
