ページ1に含まれる内容の要旨
HK250.O/M.QXD 9/26/02 3:49 PM Page 1
WARNING
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THIS PLUG WITH AN
EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES
CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. TO PREVENT FIRE
OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with CAUTION: TO REDUCE
arrowhead symbol, THE RISK OF ELECTRIC The exclamation point
within an equilateral SHOCK DO NOT within an equi
ページ2に含まれる内容の要旨
HK250.O/M.QXD 9/26/02 3:49 PM Page 2 IMPORTANT SAFETY PRECAUTIONS (CONTINUED) source. This product should not be placed in an enclosed environment unless proper ventilation is provided. 7. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your dealer or local power company. 8. Do not allow anything to rest on the power cord. Do not locate this product where the cord will be a
ページ3に含まれる内容の要旨
HK250.O/M.QXD 9/26/02 3:49 PM Page 3 IMPORTANT SAFETY PRECAUTIONS (CONTINUED) FCC wants you to know This equipment complied with part 68 of the FCC rules ACTA technical requirements. On the bottom of the base of this equipment is a label that contains, among other information, the FCC Registration Number and Ringer Equivalence Number (REN) for this equipment. You must, upon request, provide this information to your telephone company. The USOC number of the registration jack for the equipment
ページ4に含まれる内容の要旨
HK250.O/M.QXD 9/26/02 3:49 PM Page 4 IMPORTANT SAFETY PRECAUTIONS (CONTINUED) However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between t
ページ5に含まれる内容の要旨
HK250.O/M.QXD 9/26/02 3:49 PM Page 5 LOCATION OF CONTROLS AND INDICATORS BASE HANDSET 14 22 27 1 2 23 3 4 5 15 28 6 24 7 16 8 17 9 10 18 25 11 19 26 12 20 21 13 HANDSET: 16. CHN (Channel) Button 1. Belt Clip 17. Headset Jack 2. Earpiece 18. #/ ❿ Button 3. Display 19. REDIAL Button 4. REVIEW/VOLUME / ❷ Buttons 20. PAUSE Button 5. CID Button 21. Battery Compartment (Rear of Unit) 6. TALK Button 7. ERASE Button BASE: 8. RINGER ON/OFF Switch 22. TEL LINE Jack (Rear of Base) 9. Key Buttons (0-9)
ページ6に含まれる内容の要旨
HK250.O/M.QXD 9/26/02 3:49 PM Page 6 LOCATION OF CONTROLS AND INDICATORS (CONTINUED) DISPLAY 34 56 7 1 8 2 JUDI SMITH 9 973-555-1234 1. MEM (Memory) Indicator - Indicates the unit is in Memory Dial Programming mode or Memory Dialing mode. 2. REP (Repeat) Indicator - Indicates how many phone calls have been made from the same telephone number. 3. NEW Indicator - Indicates the number of new caller ID data items that have not been reviewed. 4. TOTAL Indicator - Indicates the total number of stor
ページ7に含まれる内容の要旨
HK250.O/M.QXD 9/26/02 3:49 PM Page 7 INSTALLATION INSTRUCTIONS 1. Carefully unpack and remove your unit from the box. 2. Make sure all of the following items have been included: Base Unit AC Adapter Handset Unit (AC120V, 60Hz/DC9V, 300mA) Rechargeable Ni-MH Battery Pack Telephone Cord (3.6V, 600mAH) Memory Label 3. Make sure the Rechargeable Battery is installed or install the Rechargeable Battery as described on the next page. PLEASE REFER TO THE FOLLOWING DIAGRAM FOR STEPS 4 TH
ページ8に含まれる内容の要旨
HK250.O/M.QXD 9/26/02 3:49 PM Page 8 INSTALLATION INSTRUCTIONS (CONTINUED) Installation of the Rechargeable Battery 1 2 Remove the battery cover located on Plug the new battery into the recharge- the rear of the handset by pressing on able battery plug and insert the the top cover and sliding it downward. rechargeable battery into the battery compartment. NOTE: The plug will fit only one way. If you have difficulty, be sure the plug and socket are aligned properly. 3 Put the battery cover ba
ページ9に含まれる内容の要旨
HK250.O/M.QXD 9/26/02 3:49 PM Page 9 SET-UP INSTRUCTIONS SETTING THE LANGUAGE Set the language (ENGLISH, SPANISH, FRENCH) as follows: 1 2 1 2 Press and hold the ERASE button ❶ While in the Standby mode, press the PROG button. for more than two seconds or press the TALK button ❷ twice to clear any displayed number and return to the Standby mode. 3 4 2 1 Press the REVIEW/VOLUME Press the ➛ or ❿ button ❶ to select button ❶ once or the REVIEW/ the desired language (ENGLISH, VOLUME ❷ button ❷ thr
ページ10に含まれる内容の要旨
HK250.O/M.QXD 9/26/02 3:49 PM Page 10 SET-UP INSTRUCTIONS (CONTINUED) SETTING THE AREA CODE In order for the Caller ID redial feature to work properly, you must set the phone to your local area code as described below. If you live in a town with more than one area code, do not enter an area code for this option. 1 2 1 2 Press and hold the ERASE button ❶ While in the Standby mode, press the PROG button. for more than two seconds or press the TALK button ❷ twice to clear any displayed number an
ページ11に含まれる内容の要旨
HK250.O/M.QXD 9/26/02 3:49 PM Page 11 SET-UP INSTRUCTIONS (CONTINUED) SETTING THE LCD CONTRAST If you find the LCD screen difficult to read, set the contrast level as follows: 1 2 1 2 Press and hold the ERASE button ❶ While in the Standby mode, press the PROG button. for more than two seconds or press the TALK button ❷ twice to clear any displayed number and return to the Standby mode. 3 4 2 1 Press the REVIEW/VOLUME Press the ➛ or ❿ button to select one button ❶ three times or the REVIEW/ o
ページ12に含まれる内容の要旨
HK250.O/M.QXD 9/26/02 3:49 PM Page 12 BASIC OPERATION RINGER SWITCH TONE/PULSE SWITCH 1 1 Slide the RINGER ON/OFF switch on Slide the TONE/PULSE switch on the the side of the handset to the ON side of the base to TONE or PULSE to position to turn the ringer on. Slide the match the service provided on your RINGER switch to the OFF position to telephone line. If you are not sure of turn the ringer off. your service, please contact your telephone company. AUTO TALK AND AUTO STANDBY The Auto Talk
ページ13に含まれる内容の要旨
HK250.O/M.QXD 9/26/02 3:49 PM Page 13 BASIC OPERATION (CONTINUED) RECEIVING A CALL The last 99 incoming calls are saved in the Caller ID log. 1 Make sure that the Caller ID service is turned on by your phone company. When you receive a call, the display will show the name of the caller and number of the call. To answer the call if the handset is out of the base, press the TALK button. If the handset is in the base, simply remove it from the base. The display will show the amount of time you h
ページ14に含まれる内容の要旨
HK250.O/M.QXD 9/26/02 3:49 PM Page 14 BASIC OPERATION (CONTINUED) REDIALING A NUMBER CHANNEL SELECTION 1 1 1 2 Press the TALK button ❶ (the light will The base unit will automatically search for the clearest channel in the Standby mode. come on), followed by the REDIAL However, should you hear static or noise button ❷ to automatically redial the during the course of a conversation which last number dialed on this handset (up makes it difficult to hear the caller, the CHN to 32 digits). (Chann
ページ15に含まれる内容の要旨
HK250.O/M.QXD 9/26/02 3:49 PM Page 15 BASIC OPERATION (CONTINUED) USING THE TONE BUTTON CALL WAITING 1 1 If you are in a Pulse dialing area you If you subscribe to Call Waiting through your local phone company, and you may still take advantage of touch-tone receive another phone call, the phone services after dialing to respond to will alert you with a beep and the display touch-tone prompts. To do this, press will show the name and number. Simply the */TONE/ ➛ button to temporarily press the
ページ16に含まれる内容の要旨
HK250.O/M.QXD 9/26/02 3:49 PM Page 16 BASIC OPERATION (CONTINUED) MESSAGE WAITING FUNCTION When a caller has recorded a message on a personal message service, “ ” will appear in the display and will disappear when you retrieve your message. This feature is only for subscribers of a voice mail message waiting service. DIGITAL SECURITY SYSTEM The security code prevents your cordless telephone conversation from being accessed by a phone on a different line. Once the handset battery is fully cha
ページ17に含まれる内容の要旨
HK250.O/M.QXD 9/26/02 3:49 PM Page 17 BASIC OPERATION (CONTINUED) CHECKING THE CALLER ID LOG 1 1 2 To scroll through the calls, press the CID button ❶; the New Calls and the Total Calls will appear in the display. Press the REVIEW/VOLUME button ❷ to go through the calls from the first call received to the last. Press the REVIEW/ VOLUME ❷ button ❸ to go through the calls from the last call received to the first. Press the CID button ❶ again when done. NOTES: The NEW indicator will blink unt
ページ18に含まれる内容の要旨
HK250.O/M.QXD 9/26/02 3:49 PM Page 18 BASIC OPERATION (CONTINUED) DELETING ONE NAME/NUMBER FROM THE CALLER ID LOG 1 2 1 1 2 2 Scroll through the calls to select a Press the PROG button ❶ then press number to delete by pressing the CID the ERASE button ❷ ; “DELETED” will button ❶ and then scroll by pressing the appear in the display and a confirmation REVIEW/VOLUME / ❷ buttons ❷. tone will be heard. DELETING ALL NAME(S)/NUMBER(S) FROM THE CALLER ID LOG 1 2 1 2 Press the CID button. Press the
ページ19に含まれる内容の要旨
HK250.O/M.QXD 9/26/02 3:49 PM Page 19 BASIC OPERATION (CONTINUED) EDITING TELEPHONE NUMBERS You can edit a phone number in the caller ID as follows: 1 2 1 2 Scroll through the calls to select a Press the PROG button to select the number to edit by pressing the CID menu. button ❶ and then scroll by pressing the REVIEW/VOLUME / ❷ buttons ❷. 3 4 Press the ERASE button; the “1” will be Press the REVIEW/VOLUME ❷ button to go to the number; the first “1” deleted and the second digit will start wil
ページ20に含まれる内容の要旨
HK250.O/M.QXD 9/26/02 3:49 PM Page 20 BASIC OPERATION (CONTINUED) EDITING CALLER NAMES You can edit a name in the caller ID as follows: 1 2 1 2 Scroll through the calls to select a Press the PROG button to select the name to edit by pressing the CID menu. button ❶ and then scroll by pressing the REVIEW/VOLUME / ❷ buttons ❷. 3 1 4a 2 TO ERASE THE CHARACTER: Press Press the REVIEW/VOLUME button ❶ to start character editing. the ERASE button; the next character will move one step to the left.
