Toshiba SX-2801の取扱説明書

デバイスToshiba SX-2801の取扱説明書

デバイス: Toshiba SX-2801
カテゴリ: コードレス電話
メーカー: Toshiba
サイズ: 1.39 MB
追加した日付: 7/28/2014
ページ数: 40
説明書を印刷

ダウンロード

使い方は?

私たちの目的は、皆様方にデバイスToshiba SX-2801の取扱説明書に含まれたコンテンツを可能な限り早く提供することです。オンラインプレビューを使用すると、Toshiba SX-2801に関してあなたが抱えている問題に対する解決策の内容が素早く表示されます。

便宜上

説明書Toshiba SX-2801をこちらのサイトで閲覧するのに不都合がある場合は、2つの解決策があります:

  • フルスクリーン表示 – 説明書を(お使いのコンピュータにダウンロードすることなく)便利に表示させるには、フルスクリーン表示モードをご使用ください。説明書Toshiba SX-2801のフルスクリーン表示を起動するには、全画面表示ボタンを押してください。
  • コンピュータにダウンロード - Toshiba SX-2801の説明書をお使いのコンピュータにダウンロードし、ご自身のコレクションに加えることもできます。デバイス上のスペースを無駄にしたくない場合は、いつでもManualsBaseサイトでダウンロードすることもできます。
Toshiba SX-2801 取扱説明書 - Online PDF
Advertisement
« Page 1 of 40 »
Advertisement
印刷版

多くの人々は画面表示ではなく印刷された説明書を読むほうを好みます。説明書を印刷するオプションも提供されており、上記のリンクをクリックすることによりそれを利用できます - 説明書を印刷。説明書Toshiba SX-2801を全部印刷する必要はなく、選択したページだけを印刷できます。紙を節約しましょう。

要旨

次のページにある説明書Toshiba SX-2801の内容のプレビューは、以下にあります。次のページにある説明書の内容をすぐに表示したい場合は、こちらをご利用ください。

内容要旨
ページ1に含まれる内容の要旨

Preparation Basics Caller ID/Call waiting
Additional Information
SX-2801.qxd 3/15/1 6:02 PM Page 1
,
OWNER S MANUAL
900MHz DIGITAL SPREAD SPECTRUM CORDLESS TELEPHONE
-
SX 2801
The FIRST thing to do after unpacking your new
cordless telephone is:
CHARGE THE BATTERY !
Please read and follow the few instructions on
PAGE 2
BEFORE YOU DO ANYTHING ELSE.

ページ2に含まれる内容の要旨

SX-2801.qxd 3/15/1 6:02 PM Page 2 GETTING STARTED: DO THIS FIRST! FIRST, CHARGE THE HANDSET BATTERY! • Set your new phone in an out-of-the-way place near a power outlet where it will not be disturbed. • Plug the AC adaptor into the wall outlet. • Plug the AC adaptor cord into the power jack on the base unit. • Take the cover off the handset battery compartment; plug the battery connector into the receptacle inside the battery compartment and replace the cover. The connector only goes in one w

ページ3に含まれる内容の要旨

Preparation SX-2801.qxd 3/15/1 6:02 PM Page 3 INTRODUCTION FEATURES Toshiba America Consumer Products, Inc., takes pride in presenting the new 900 MHz digital spread spectrum cordless telephone. The Toshiba cordless telephone features a 16-digit x 3-line dot matrix liquid crystal display (LCD) for caller ID on Call Waiting and speed-dial programming and calling. The sleek new design provides face-up battery charging even when wall mounted. Other features are summarized below. • 900 MHz Digital

ページ4に含まれる内容の要旨

SX-2801.qxd 3/15/1 6:02 PM Page 4 TABLE OF CONTENTS Preparation INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . .6 LOCATION OF CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Handset . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ページ5に含まれる内容の要旨

SX-2801.qxd 3/15/1 6:02 PM Page 5 TABLE OF CONTENTS Steps for entering names and special characters . . . . . . . . . . . . . . .24 If you make a mistake while entering a name . . . . . . . . . . . . . . . . . .25 Dialing a stored number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 Editing and deleting stored numbers . . . . . . . . . . . . . . . . . . . . . . . .26 Caller ID/Call waiting CALLER ID/CALL WAITING . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ページ6に含まれる内容の要旨

SX-2801.qxd 3/15/1 6:02 PM Page 6 IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment, 9 Never push objects of any kind into this product through cabinet slots as basic safety precautions should always they may touch dangerous voltage be followed to reduce the risk of fire, points or short out parts that could electric shock and injury. result in a risk of fire or electric shock. 1 Read and understand all instructions. Never spill liquid of any kind on the 2 Follow all warnings a

ページ7に含まれる内容の要旨

Preparation SX-2801.qxd 3/15/1 6:02 PM Page 7 IMPORTANT SAFETY INSTRUCTIONS TM The RBRC Seal TM The RBRC Seal on the (easily removable) nickel-cadmium battery (contained in our product) indicates that Toshiba America Consumer Products, Inc. (TACP) is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful lives, TM when taken out of service within the United States. The RBRC program provides a convenient alternative to placing used ni

ページ8に含まれる内容の要旨

 TALK MEM PAUSE FUNCTION DELETE REDIAL FLASH VOL/RING SELECT L.D. LOCAL TONE CHANNEL SX-2801.qxd 3/15/1 6:02 PM Page 8 LOCATION OF CONTROLS HANDSET Antenna Headset jack VOL/RING () button (up arrow button) Liquid Crystal Display (LCD) VOL/RING () button (down arrow button) (page 19) REDIAL ( ) button (Left arrow button) FLASH ( ) button (Right arrow button) (page 19) (page 14, 32) TALK SELECT button (page 22 to 26, 31 to 33) button (page 18) L.D./1 button (page 30) CID (Caller ID) button

ページ9に含まれる内容の要旨

Preparation Preparation SX-2801.qxd 3/15/1 6:02 PM Page 9 LOCATION OF CONTROLS BASE UNIT DC IN 9V jack (page 10) LINE modular jack (page 10) Hook Antenna Cradle IN USE/CHARGE LED PAGE button (page 21) Charging contacts For purchase of accessories, please call 1-877-644-7373. Owner’s manual Part # RC009798 Rechargeable Battery Pack Quick Reference Guide Toshiba TRB-8000 Part # RC009799 Part # RC004931 9

ページ10に含まれる内容の要旨

SX-2801.qxd 3/15/1 6:02 PM Page 10 INSTALLATION SETTING UP THE BASE UNIT (DESK TOP MOUNTING) For setting up the base unit follow the instructions below. Raise the antenna to vertical position. Telephone Line Cord Single-Line Telephone Jack Fasten the AC adaptor (RJ11C) cord to prevent it from being disconnected. Power Outlet (AC 120 V, 60 Hz) AC Adaptor • Plug the AC adaptor firmly into the base unit and the AC 120V outlet. • USE ONLY WITH Supplied AC ADAPTOR (TAC-1700 power source AC 120V 60

ページ11に含まれる内容の要旨

Preparation Preparation SX-2801.qxd 3/15/1 6:02 PM Page 11 INSTALLATION SETTING UP THE BASE UNIT (WALL MOUNTING) MOUNTING ON A STANDARD WALL PLATE: Raise the antenna. Single-Line Telephone Telephone Jack Line Cord (RJ11C) Power Outlet (AC 120 V, 60 Hz) AC Adaptor • Route the cords through the guides. • Place the base unit on the posts of the wall plate and push down until it is firmly seated. NOTES: • Do not use any outlet controlled by a wall switch. • If you don’t have a standard wall plate,

ページ12に含まれる内容の要旨

SX-2801.qxd 3/15/1 6:02 PM Page 12 INSTALLATION CHARGING THE BATTERY PACK It is important to charge the battery for 12-16 hours continuously without any interruption before you use the handset for the first time. 1 Remove the battery cover on the Red Black back of the handset by sliding it down. 2 Plug the battery pack cord into the connector with the correct polarity. (black and red wires). 3 Place the battery pack in the battery compartment. 4 Put the battery cover back by sliding until it

ページ13に含まれる内容の要旨

Preparation Preparation SX-2801.qxd 3/15/1 6:02 PM Page 13 INSTALLATION NOTES: • Use only the supplied battery pack (TRB-8000 power source 600mAh, 3.6VDC) • The battery pack is not charged properly if the charging contacts are dirty or tarnished. Clean the contacts occasionally with a dry cloth. After the battery pack is fully charged; Operation Approx. battery life While in use (Talk mode) up to 6 hours While not in use (Standby mode) up to 10 days When "Low Battery" blinks on the LCD, all h

ページ14に含まれる内容の要旨

SX-2801.qxd 3/19/1 9:26 AM Page 14 INSTALLATION Before using the Handset, make sure to read the following instructions. FLASH SELECT TONE/ PULSE / FUNCTION SETTING THE DIAL MODE Depending on your dialing system, set the mode as follows: 1 Press and hold FLASH until you hear a confirmation tone. 2 To set the dial mode for Dial Mode:Pulse Dial Mode:Tone pulse dialing, press Tone - Press Tone - Press Pulse- Press # Pulse- Press # PULSE / . Or to set the dial mode for tone PULSE TONE/ / TONE/

ページ15に含まれる内容の要旨

Preparation Preparation SX-2801.qxd 3/15/1 6:02 PM Page 15 INSTALLATION SETTING OR CANCELING THE AUTO TALK FUNCTION If the handset is placed on the base unit, you can answer a call by lifting the handset from the base unit (Auto Talk). If the handset is not on the base unit, you can answer a call by pressing any one of the buttons (Any-key Answer function). When the Auto Talk function is set to ON, the Any-key Answer function is also set to ON. When the Auto Talk function is set to OFF, you c

ページ16に含まれる内容の要旨

SX-2801.qxd 3/15/1 6:02 PM Page 16 INSTALLATION SETTING THE AREA CODE It is necessary to program your area code so that local calls will be displayed properly on caller ID. 1s sAuto Talk:Off 2 CIDCW:On 1Press . FUNCTION 3 Area Code: 1 Auto Talk:Off 2 CIDCW:On 3 2 Press or to move the pointer to Area 3s sArea Code: Code. 1 Auto Talk:Off 2 CIDCW:On 3Press . SELECT 3 Area Code:615 Enter a 3-digit area code. For example, enter “615.” If you enter a wrong number, press DELETE . 1 Auto Talk:Off

ページ17に含まれる内容の要旨

T TA AL LK K Preparation SX-2801.qxd 3/15/1 6:02 PM Page 17 INSTALLATION USING A HEADSET You can use an optional headset (part#: RC 008260) that has a 3/32- inch(2.5mm) plug. To connect the headset, open the rubber cover on the left side of the handset, then insert the headset's plug into the jack. With a headset connected, you can make or answer calls as usual using the keys on the handset. When you finish using the headset, disconnect it from the handset and close the rubber cover to protect

ページ18に含まれる内容の要旨

SX-2801.qxd 3/15/1 6:02 PM Page 18 BASIC OPERATION Before using the Handset, make sure to read the following instructions. VOL/RING() REDIAL FLASH TALK VOL/RING() / PULSE TONE/ CHANNEL DELETE / MAKING A CALL Handset On The Base Handset Off The Base TALK 1) Pick up the handset. 1) Press . TALK 2) Press . 2) Listen for the dial tone. 3) Listen for the dial tone. 3) Dial the number. 4) Dial the number. OR TALK OR Dial the number, then press . 1) Pick up the handset. TALK 2) Dial the number, then

ページ19に含まれる内容の要旨

Basics SX-2801.qxd 3/15/1 6:02 PM Page 19 BASIC OPERATION 3 NUMBER REDIAL You can redial any of the last three numbers dialed from the handset: REDIAL 1 Press in standby mode. The last dialed number (Redial 1) appears. REDIAL Each time you press , the LCD displays one of the three last dialed numbers (Redial 1 to Redial 3). TALK 2 After the desired number has been selected, press . The call will be connected. NOTES: • The handset redials only up to 32 digits even for a number that exceeds this

ページ20に含まれる内容の要旨

SX-2801.qxd 3/15/1 6:02 PM Page 20 BASIC OPERATION TONE/PAUSE To Do this TONE/ To temporarily switch to tone dial Press . The following numbers will (When the base is set to pulse mode), be sent as tone dialing. see page 14. To enter a pause within the dialing sequence PAUSE Press . “P” appears in the display which represents a pause. PAUSE EXAMPLE : To make a call “0 12345678” with tone dialing in 0 2 3 4 5 6 TONE/ PAUSE 1 pulse mode, press 7 8 . INTERFERENCE OR STATIC If you hear noise duri


類似の説明書
# 取扱説明書 カテゴリ ダウンロード
1 Toshiba 151D 取扱説明書 コードレス電話 3
2 Toshiba DKT2204-CT 取扱説明書 コードレス電話 1
3 Toshiba FT-8001 AW 取扱説明書 コードレス電話 22
4 Toshiba 162D 取扱説明書 コードレス電話 1
5 Toshiba DKT2104-CT 取扱説明書 コードレス電話 4
6 Toshiba FT-8981 取扱説明書 コードレス電話 6
7 Toshiba FT 8000 取扱説明書 コードレス電話 95
8 Toshiba 162 取扱説明書 コードレス電話 3
9 Toshiba FT-8801A 取扱説明書 コードレス電話 8
10 Toshiba FT-8001 A 取扱説明書 コードレス電話 12
11 Toshiba SG 1000 取扱説明書 コードレス電話 1
12 Toshiba DKT2304-CT 取扱説明書 コードレス電話 1
13 Toshiba SG-1700 取扱説明書 コードレス電話 3
14 Toshiba SG-1600 取扱説明書 コードレス電話 1
15 Toshiba STRATA CTX DKT2004-CT 取扱説明書 コードレス電話 1
16 Sony SPP-111 取扱説明書 コードレス電話 34
17 Sony SPP-A2470 取扱説明書 コードレス電話 4
18 Sony PP-A2780 取扱説明書 コードレス電話 5
19 Sony SPP-933 取扱説明書 コードレス電話 21
20 Sony SPP-934 取扱説明書 コードレス電話 7