ページ1に含まれる内容の要旨
OWNER'S
MANUAL
MODEL NO.
• o,,oo,
)
274.43948590
SERIES
Record the Model No. and the
Serial No. of your television in
SEARS
the space provided.
31" TABLETOP
Model No.
COLOR TELEVISION
Serial No.
WITH REMOTE CONTROL
Keep this information for
future use.
Safety Information
Use
Warranty and Service
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
ページ2に含まれる内容の要旨
Important Information WARNING TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER To reduce the risk of fire or SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. shock hazard, do not expose this TV to rain or moisture. This symbol indicates "dangerous voltage" inside important instructions This symbol indicates the product that presents a accompanying the risk of electric shock or product. personal injury. CAUTION: To prevent electric shock, match
ページ3に含まれる内容の要旨
Table of Contents Important Information Warning Quick Guide to Your TV Startup .............................................................................. 2-3 Set up, Hook up, Plug in the TV, Put Batteries in the Remote, Turn on the TV, Adjust Picture Tilt, Place Channels into Memory, Set the Time Tour of the Remote 4 Basic Button Layout and Functions Guide to the Menus 5 Colors, Menu Buttons, Moving through the Menus With Remote Buttons 6-7 Using Your TV and Remote With VCRs 8-10 11 With Sat
ページ4に含まれる内容の要旨
Quick Guide to Your TV Startup The steps below will get your TV connected and ready for watching. For more details, see the page numbers listed. Hook up any antennas, cables or 1. Hook up your TV CONNECTIONS GUIDE other equipment to your TV before Details are in the Connections you follow the steps below. Guide. Plug the cord into the outlet, 2. Plug in the TV matching the wide and the small end of the plug with the outlet. A. Pull off the cover of the battery 3. Put Batteries in the Remote comp
ページ5に含まれる内容の要旨
Quick Guide to Your TV Startup A. Make sure STRENG'IH switch is 5. Adjust PICTURE TILT. in the OFF position. BACK OF TV Picture tilt is used to correct a B. Move STRENGTH switch to the tilted picture from the effect of the LOW position. If this does not Earth's magnetic field on a large OFF HIGH fully improve tilt, move LOW picture tube. The PICTURE TILT STRENGTH switch to HIGH. STRENGTH and POLARITY This should correct tilt. If moving switches on the back of the TV STRENGTH switch makes tilt co
ページ6に含まれる内容の要旨
Quick Guide to Your TV Basic Tour of the Remote Basic information about your remote is shown below. This will give you a general idea of how your remote works. For more details, see pages 6-15. TV Power Button 'lUreS the 'IV on. Sets the remote to control the rJ'v. Volume and Channel Controls Operates TV when remote is set to control the TV. Details are on page 6. Operates the TV and advanced features. Controls components such as a Component Buttons VCR, laserdisc player, audio Details are on pa
ページ7に含まれる内容の要旨
Quick Guide to Your TV Menu Basics General information about using the on-screen menu system is shown below. Details on using the remote buttons are on pages 6-7. Many menu items are explained in detail in Using the Advanced Features starting on page 20. Yellow Green Light White Press MENU*PROG repeatedly to Colors see each of the four menu colors. 1 Bie 1 -- Each menu has a different color background as shown at the left. Controls Alarm Menu Buttons The menu buttons are used to adjust the featu
ページ8に含まれる内容の要旨
Using Your TV and Remote With Remote Buttons REG (Record) POWER Turns off the TV. Starts recording onto tape. Turns off compatible components. STOP pOWER VCRI SAT*CABLE TV Turns on a component after a Stops tape or laserdisc. component button is pressed. PAUSE AUDIO, VCR1, VCR2.LD, REW PLAY FF Pauses tape or laserdisc. SAT.CABLE, TV Sets the remote to control the DISPLAY REC STOP PAUSE m rT! component. VCR2. LD can only be Shows displays on the screen. DISPLAY SKIP programmed for one component:
ページ9に含まれる内容の要旨
Using Your TV and Remote With Remote Buttons Number Buttons (0-9) MENUoPROG (Program) Shows menus on the screen and Selects any channel number. moves from menu to menu. Two numbers must be pressed tor pOWER VCR1 SATOCABLE TV Sets VCR clock and programs each channel. Press 0 and 6 for timer on VCR. AUDIO channel 6. For three digit vC LD 0 channels, press and hold 1 until 1-- RESET REW PLAY FF appears on the screen. Then press Returns the picture adjustments to the other two numbers. the original
ページ10に含まれる内容の要旨
Using Your TV and Remote With VCRs: Programming the Remote Refer to the Connection Book or the VCR's owners manual to hook up your VCRs. The remote may need to be programmed for your VCR, but may not operate all models of the brands listed below. Use the codes below or on the sheet packed in with your remote. A. Press VCR1 or VCR2"LD to turn 1. Test the remote the VCR on. B. Press the VCR buttons shown at _w p_¥ fF the left. If your VCR does not work, program VGR1 or r__ VCR2.LD with a VCR code
ページ11に含まれる内容の要旨
Using Your TV and Remote With VCR: Setting the VCR1 Channel The VCR 1 Channel works with the VCR1 button on the remote. If the VCR 1 Channel is set, pressing VCR selects the channel to see the VCR picture. The VCR 1 Channel setting depends on which diagram you have used from the Connection Guide. If you want to turn this feature off, set the VCR 1 Channel to Disable. Refer to the chart below for your setting. A. Press TV to set the remote to 13 1. Select the Setup Menu control the TV. B. Press M
ページ12に含まれる内容の要旨
Using Your TV and Remote With VCRs: Basic Operation If the remote operates your VCR, this page will show you how to use it tot basic functions. See pages 6-7for more details on buttons used with your VCR. _0_t. vcRi sA_°c_ rv Turn on the VCR ,\. 1'I(_'55 _ll_1,_l_ci ()U, U_, ui 04 OiL QO the TV to see what the VCR is doing. B. Press VCR1 or VCR2°LD to set °SY_ 5 the remote to control the VCR. C. Press POWER to turn on the VCR if it did not turn on when _0 _0 _0 you pressed VCR1 or _0 _0 _0 VCR2°
ページ13に含まれる内容の要旨
Using Your TV and Remote With a Satellite Receiver: Basic Operation You may also be able to use the TV's remote with satellite receivers. Refer to your Satellite Receiver owner's manual to hook up your Satellite Receiver. The remote may need to be programmed for other brands of satellite receivers, but may not operate all models of the brands listed below. Use the codes below or on the sheet packed in with your remote. Follow the instructions below for basic operation of your receiver. You may a
ページ14に含まれる内容の要旨
Using Your TV and Remote With a Cable Box: Programming and Basic Operation Refer to the Connection Book or contact your cable company to hook up your cable box. If you have a cable box with its own remote, then you may also be able to use the TV's remote with your cable box. This remote may not operate all models of the brands listed below. Use the codes below or on the sheet packed in with your remote. Program the remote for your A. Point the remote at the cable cable box box and hold SAT,CABLE
ページ15に含まれる内容の要旨
Using Your TV and Remote With a Cable Box: Setting the Cable Channel The Cable Channel works with SAT.CABLE button on the remote. If the Cable Channel is set, pressing SAT,CABLE selects the channel to see cable channels. The Cable Channel setting depends on which channel your cable box must be on to see cable channels. The channels usually used are 02, 03, 04, 05 or 06. Consult your cable company for more information. A. Press TV to set the remote to 13 1. Select the Setup menu control the TV. B
ページ16に含まれる内容の要旨
Using Your TV and Remote With a Laserdisc Player: Programming and Basic Operation Refer to your Laserdisc Player owner's manual to hook up your Laserdisc Player. The remote may need to be programmed for your laserdisc player, but may not operate all models of the brands listed below. Use the codes below or on the sheet packed in with your remote. A. Point the remote at the Program the remote for laserdisc player and hold your Laserdisc Player VCR2. LD. 1 SATOCABLE TV B. Enter the code for your b
ページ17に含まれる内容の要旨
Using Your TV and Remote With Audio Equipment: Programming and Basic Operation Refer to the Connection Book or your Audio equipment owner's manual to hook up your audio equipment. Your remote controls some audio equipment such as a radio, CD player, tape player, turntable, or amplifier. The remote may need to be programmed for your equipment, but may not operate all models of the brands listed below. Use the codes below or on the sheet packed in with your remote. A. Point the remote at the audio
ページ18に含まれる内容の要旨
Adjusting Your TV Overall Picture Follow the steps below to lighten or darken the overall picture without changing the color level. Press MENU,PROG to select the 1. Select the Controls Menu Controls menu. This menu is yellow. Alarm Ad Press MOVE • to highlight 2. Highlight Picture Picture. Alarm Press MOVE I_ to lighten the . Use MOVE I_ and _I to picture. adjust the Picture OR Press MOVE ,! to darken the picture. [_lr_lll=_ ............ 16
ページ19に含まれる内容の要旨
Adjusting Your TV Picture Settings Follow the steps below to change the picture on the screen to your personal setting. The chart at the bottom of the page explains your options. Press MENU,PROG repeatedly to 1. Select the Adjust Menu select the Adjust menu. This menu is light blue. Controls Alarm 2. Highlight item to change Press MOVE • to highlight the picture item you want to adjust. 1 Use MOVE • or _ to Press MOVE • or • to adjust each item. adjust each item Controls Alarm Press MOVE • to: P
ページ20に含まれる内容の要旨
Adjusting Your TV Sound Settings: Stereo, Expanded Stereo, SAP and Tone Follow these steps to adjust the Stereo, Expanded Stereo, SAP or Tone of your TV. SAP (Second Audio Program) is sometimes used to offer the program being watched in another language. The chart below explains your options. Press MENU,PROG to select the 1. Select the Controls Menu Controls menu. This menu is yellow. Alarm Ad Press MOVE • to highlight the 2. Highlight item to change sound item you want to adjust. Press MOVE • o
