ページ1に含まれる内容の要旨
L53V2/XE (VCC-5775P) GB 2000, 7, 11
INSTRUCTION MANUAL VCC-5775P
BEDIENUNGSANLEITUNG
MANUEL D’INSTRUCTIONS
COLOUR CCD camera
CCD-Farbkamera
Caméra CCD COULEUR
CCD
About this manual A propos de ce manuel
Before installing and using the camera, please read this Avant d’installer et d’utiliser la caméra, veuillez lire ce
manual carefully. Be sure to keep it handy for later reference. manuel attentivement. Gardez-le à portée de main pour
toute référence ultérieure.
Über diese Bedienungsanleitung
Le
ページ2に含まれる内容の要旨
L53V2/XE (VCC-5775P) GB 2000, 7, 11 Depending on the conditions of use, installation CONTENTS and environment, please be sure to make the appropriate settings and adjustments. If you PRECAUTIONS .............................. 3 need help with installation and/or settings, please consult your dealer. PARTS NAMES .............................. 5 MOUNTING THE LENS.................. 7 CONNECTIONS.............................. 9 FLANGE-BACK ADJUSTMENT ...... 11 SETTINGS ..............................
ページ3に含まれる内容の要旨
ENGLISH L53V2/XE (VCC-5775P) GB 2000, 7, 11 FEATURES Built-in interline transfer method 1/3" CCD, approx. 470,000 picture elements Low smear, anti-blooming, low lag, no burning and no geometric distortion using the CCD solid state image device. 100% solid state components giving excellent immunity to shock and vibration Not subject to interference from magnetic or electrostatic fields High sensitivity, minimum required illumination is 1.4 lux (F1.2) Horizontal resolution, more than 4
ページ4に含まれる内容の要旨
L53V2/XE (VCC-5775P) GB 2000, 7, 11 PRECAUTIONS In case of problem Be careful when handling the unit Do not use the camera if smoke or a strange odour To prevent damages, do not drop the camera or comes from the unit, or if it seems not to function subject it to strong shock or vibration. correctly. Disconnect the power cord immediately, Install away from electric or magnetic and consult your dealer (or a Sanyo Authorized fields Service Centre). If installed close to a TV, radio transmitter, mag
ページ5に含まれる内容の要旨
L53V2/XE (VCC-5775P) GB 2000, 7, 11 PRECAUTIONS Protect from high temperatures Cleaning Do not install close to stoves, or other heat Dirt can be removed from the cabinet by generating devices, such as spotlights, etc., or wiping it with a soft cloth. To remove stains, where it could be subject to direct sunlight, as that wipe with a soft cloth moistened with a soft could cause deformation, discoloration or other detergent solution and wrung dry, then wipe damages. dry with dry soft cloth. Be
ページ6に含まれる内容の要旨
L53V2/XE (VCC-5775P) GB 2000, 7, 11 PARTS NAMES 1Camera mounting screw hole 2 CAUTION: 3 When installing the camera, select a location that can support the total weight of the camera and accessories. 2Electronic iris function switch (EI OFF/EI ON) 1 3Sync switch (INT/L-L) 4 INT (Internal sync) position L-L (Line lock) position 4Line phase adjustment volume (LINE PHASE) 5Lens iris level volume (LEVEL) 6Lens iris output connector (LENS) 5 This 4-pin connector is used to send the DC control signal
ページ7に含まれる内容の要旨
L53V2/XE (VCC-5775P) GB 2000, 7, 11 PARTS NAMES 8 7Flange-back lock screw 8CS mount ring 9Lens mount cap The cap is installed to protect the lens mount section. Remove the lens mount cap before installing a lens. 7 FVideo output connector (VIDEO OUT: BNC type) Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector. 9 7 G24 V AC or 12 V DC input terminal (24 V AC, 12 V DC, GND) … See page 9 G F 6 English
ページ8に含まれる内容の要旨
L53V2/XE (VCC-5775P) GB 2000, 7, 11 MOUNTING THE LENS Please use a DC type auto-iris lens (sold separately). Checking the lens mount Do not use lense with a length L more than 5 mm. If not, that may L damage the camera and prevent proper installation. 1 Remove the lens mount cap from the camera. 1 2 Install the auto-iris lens. CS mount type lens C mount Carefully align the lens mount with the camera opening, then turn the lens 2 type lens slowly to install it. C mount type lens Install the supp
ページ9に含まれる内容の要旨
L53V2/XE (VCC-5775P) GB 2000, 7, 11 MOUNTING THE LENS Rewiring the lens cable in the lens iris plug 1 1 Prepare the lens cable. Cut the cable at the plug, then remove approx. 8 mm of the cable sheath and 2 strip about 2 mm from each wire. 2 Install the lens iris plug. Solder the cable to the pins following the correct pin layout (refer to the table and illustrations), then close the plug cover. 2 1 2 Compatible auto-iris lenses (1/3 inch COSMICAR DC type lens) 1 4 3 Standard angle, f= 8 mm (TS
ページ10に含まれる内容の要旨
L53V2/XE (VCC-5775P) GB 2000, 7, 11 CONNECTIONS Basic connection for monitoring or recording Note: The polarities for the 24 V AC and the 12 V DC input connectors are indicated on the rating label found on the unit back panel. AC 24 V ~ ~ GND DC 12 V + – Push to insert the cable. (Video signal connections) : VIDEO IN AC 24 V connection DC 12 V connection : VIDEO OUT DC12V + – + – Fig. 1 Fig. 2 English 9
ページ11に含まれる内容の要旨
L53V2/XE (VCC-5775P) GB 2000, 7, 11 CONNECTIONS The peripheral devices (VCR, monitor, lens, 3 Insert the plug of this power supply into etc.) and cables are sold separately. a wall outlet. 1 Make the video signal connection Adjust the picture on the monitor using the between the camera and the monitor or Brightness and Contrast controls. timelapse VCR. Coaxial cable type and maximum length 2 Power supply choices Cable type RG-59U (3C-2V), 250 m Use a commercially available 24 V AC maximum. a
ページ12に含まれる内容の要旨
L53V2/XE (VCC-5775P) GB 2000, 7, 11 FLANGE-BACK ADJUSTMENT CS mount If the pick-up surface is not correctly positioned with relation to the lens ring focal point, the picture will be out of focus (in particular when using auto-iris power zoom lenses, sold separately). If that is the case, adjust the flange-back position as described below. 1 Before installing the lens, check that the two flange-back lock screws have been tightened. If the flange-back lock screws are loose, the CS mount ring will
ページ13に含まれる内容の要旨
L53V2/XE (VCC-5775P) GB 2000, 7, 11 SETTINGS Line phase adjustment When using a camera switcher to connect 2 cameras or more to one monitor, there may be a vertical roll of the images when switched. In such a case, set as described below. 1 Set the Sync switch to the L-L position. (Monitor) 2 Switch the display on the monitor from camera 1 to camera 2. Adjust the LINE PHASE volume on camera 2 until the vertical roll of the image stops. EI OFF EI ON INT L-L If more than two cameras are used, plea
ページ14に含まれる内容の要旨
L53V2/XE (VCC-5775P) GB 2000, 7, 11 SETTINGS Lens iris adjustment If using a DC type auto-iris lens, you will need to set the LEVEL volume when shooting in the conditions described below. Counterclockwise: To decrease the brightness Clockwise: To increase the brightness If shooting simultaneously in a dark room and through a bright window. If the subject background is extremely bright or dark. LEVEL If the brightness of the picture on the monitor is not correct. English 13
ページ15に含まれる内容の要旨
L53V2/XE (VCC-5775P) GB 2000, 7, 11 SETTINGS If conditions are outside the electronic iris EI (Electronic iris) function setting operation range or more than the maximum Under normal conditions, set the EI switch to brightness, it will cause saturation of the the EI OFF position and use an auto-iris lens. CCD. In that case, use a auto iris lens. However, if you have a manual lens or fixed iris lens, set the lens aperture to the shortest F stop and set the EI switch to the EI ON position. Note:
ページ16に含まれる内容の要旨
L53V2/XE (VCC-5775P) GB 2000, 7, 11 TROUBLESHOOTING Before taking the camera for repairs, please check below to make sure that the camera is used correctly. If it still does not perform correctly, please consult your dealer or a Sanyo Authorized Service Centre. No picture on the monitor screen SERVICE Is the power turned on to all connected devices? This camera is a precision instruments and if Is the voltage correct? treated with care, will provide years of satisfactory performance. However,
ページ17に含まれる内容の要旨
L53V2/XE (VCC-5775P) GB 2000, 7, 11 SPECIFICATIONS Scanning system: PAL standard Electronic iris range: (625 TV lines, 25 frames/sec.) 1.4 lux to 70,000 lux (F 1.2, lens) 2.0 lux to 100,000 lux (F 1.4, lens) Interlace: 2:1 interlace Flange-back: 12.5 mm ± 0.5 mm Image device: 1/3 inch solid state image device CCD White balance: ATW Picture elements: 798 (H) x 584 (V) Lens mount: CS mount Effective picture elements: 753 (H) x 582 (V) Environmental conditions: Synchronizing system: Manual interna
ページ18に含まれる内容の要旨
L53V2/XE (VCC-5775P) GB 2000, 7, 11 SPECIFICATIONS Dimensions: mm 51 63 (1) 68 Features and specifications are subject to change without prior notice or obligations. English 17
ページ19に含まれる内容の要旨
L53V2/XE (VCC-5775P) GB 2000, 7, 11 ACCESSORIES 12 1C mount adaptor (5 mm) ........................1 pc. The C mount adaptor must be used to be able to install a C mount lens on the camera. 2Lens iris plug (4-pin).................................1 pc. 18 English
ページ20に含まれる内容の要旨
L53V2/XE (VCC-5775P) GB 2000, 7, 11 Sanyo Electric Co, Ltd. 1AC6P1P2347-- Printed in Japan L53V2/XE(0700KP-DSP)
