Sealife DC500の取扱説明書

デバイスSealife DC500の取扱説明書

デバイス: Sealife DC500
カテゴリ: デジタルカメラ
メーカー: Sealife
サイズ: 1.13 MB
追加した日付: 2/27/2014
ページ数: 8
説明書を印刷

ダウンロード

使い方は?

私たちの目的は、皆様方にデバイスSealife DC500の取扱説明書に含まれたコンテンツを可能な限り早く提供することです。オンラインプレビューを使用すると、Sealife DC500に関してあなたが抱えている問題に対する解決策の内容が素早く表示されます。

便宜上

説明書Sealife DC500をこちらのサイトで閲覧するのに不都合がある場合は、2つの解決策があります:

  • フルスクリーン表示 – 説明書を(お使いのコンピュータにダウンロードすることなく)便利に表示させるには、フルスクリーン表示モードをご使用ください。説明書Sealife DC500のフルスクリーン表示を起動するには、全画面表示ボタンを押してください。
  • コンピュータにダウンロード - Sealife DC500の説明書をお使いのコンピュータにダウンロードし、ご自身のコレクションに加えることもできます。デバイス上のスペースを無駄にしたくない場合は、いつでもManualsBaseサイトでダウンロードすることもできます。
Sealife DC500 取扱説明書 - Online PDF
Advertisement
« Page 1 of 8 »
Advertisement
印刷版

多くの人々は画面表示ではなく印刷された説明書を読むほうを好みます。説明書を印刷するオプションも提供されており、上記のリンクをクリックすることによりそれを利用できます - 説明書を印刷。説明書Sealife DC500を全部印刷する必要はなく、選択したページだけを印刷できます。紙を節約しましょう。

要旨

次のページにある説明書Sealife DC500の内容のプレビューは、以下にあります。次のページにある説明書の内容をすぐに表示したい場合は、こちらをご利用ください。

内容要旨
ページ1に含まれる内容の要旨

DC500 Troubleshooting Updates February 2, 2006
Q – My battery does not last long and runs out after only one dive or about 50 pictures.
A – The DC500 uses the most powerful lithium rechargeable battery available. With a freshly charged
battery, you should get about 1.5 hours of use or about 100 pictures with proper power management.
Here are some tips to maximize battery life:
1. Make sure that you initially charge the battery overnight (minimum 8 hours). Then the battery must be
fully dischar

ページ2に含まれる内容の要旨

IF the date code is A through J, check to see that the two black rubber caps are in place. Without these in place the camera is not sitting properly and out of reach of the shutter button. If any of the rubber caps are missing, SeaLife can ship out a new rubber caps that the consumer can replace (Item# SL11052). IF the date code is equal to K or greater, the black rubber caps are not necessary. Other possible answer(s): The shutter button on the housing should only require about 3 pounds of

ページ3に含まれる内容の要旨

Q –The Flash Link Adapter keeps popping off, when using TWO strobes, A – The Flash Link adapter grabs around the lens port but can be pulled off under excessive stress. To avoid this it is important to feed the Flash Link cables up from under the camera and up into the adapter, so the cable is relaxed and not pulling on the adapter. It may also help to the cable to the flash arm using with a low-profile zip tie to keep firmly in position. Q – Camera has no power A – Make sure the battery is in

ページ4に含まれる内容の要旨

2. The camera will set the focus on the subject located in the center of the picture. Align the square located in the center of the LCD over the subject. Subjects outside this square may not be in focus if they are closer or farther away. The depth of field for close-up pictures is only a few inches. 3. The camera’s auto focus system needs light to “see” the subject. In darkness, the camera uses the red focusing light located next to the camera’s flash to illuminate the subject. You can als

ページ5に含まれる内容の要旨

2. Set Digital Flash Pre-Flash switch to “0”. Make sure Camera and External Flash batteries are fully charged. Turn Flash to ON and wait for green ready-light to turn on. 3. Here’s an easy test to make sure the External Flash is firing and synchronized with the camera. Take a picture of the External Flash, pointing the camera at the flash sensor. Do this with the camera removed from the flash base and without the Flash Link optical cable connected. The picture should show the flash firing. I

ページ6に含まれる内容の要旨

d. Slowly tighten the screw in _ turn increments using the Allen wrench provided. Pull on the cable after every _ turn until it’s secure. Be very careful not to over tighten the screw or you will damage the cable. If you think you may have over-tightened the screw, loosen the screw and inspect the cable. If the cable is crushed, cut off the end of the cable with a razor blade and remove about 1/16” (1.6mm) of the black sheathing. e. Attach the Flash Head Adapter to the External Flash. First,

ページ7に含まれる内容の要旨

Secure cable around flash arm or, secure cable to arm using a zip tie g. Don’t forget to insert black rubber sensor cover over flash sensor located farthest from the camera. h. Take a few test pictures to make sure the External Flash fires. i. If you still experience a flash firing issue after reviewing the above information, please send the camera system to the SeaLife Service department for a complete evaluation Q – A “card error” message appears on the LCD after powering on the camera A – Mos

ページ8に含まれる内容の要旨

3) Format the camera’s internal memory and SD memory card. The Format function is located in Set-Up mode menu. 4) Report the camera lock-up issue to the SeaLife Service center. Email: service@sealife-cameras.com. Q – The black rubber tube ring (flashguard) in the lens port area comes out. Is this normal? A – Yes, this part is designed to be removed for easy cleaning of the housing lens. This is the flashguard that prevents the inner camera’s flash from reaching the lens and causing glare. T


類似の説明書
# 取扱説明書 カテゴリ ダウンロード
1 Sealife DC100 取扱説明書 デジタルカメラ 2
2 Sealife DC 600 取扱説明書 デジタルカメラ 1
3 Sealife DC250 取扱説明書 デジタルカメラ 3
4 Sealife DC300/DC310 取扱説明書 デジタルカメラ 0
5 Sealife DC200 取扱説明書 デジタルカメラ 22
6 Sealife DC1000 取扱説明書 デジタルカメラ 5
7 Sealife DC800 取扱説明書 デジタルカメラ 2
8 Sony 3D Bloggie MHS-FS3 取扱説明書 デジタルカメラ 35
9 Sony 838 MHz to 862 MHz 取扱説明書 デジタルカメラ 7
10 Sony 4-133-499-11 (1) 取扱説明書 デジタルカメラ 15
11 Sony 4-187-045-11(1) 取扱説明書 デジタルカメラ 1
12 Sony 4-132-058-11(1) 取扱説明書 デジタルカメラ 5
13 Sony a (alpha) DSLR-A200 取扱説明書 デジタルカメラ 408
14 Sony 798 MHz to 822 MHz 取扱説明書 デジタルカメラ 0
15 Sony 3CCD COLOR BRC-300P 取扱説明書 デジタルカメラ 2