ページ1に含まれる内容の要旨
INSTRUCTION MANUAL
ZEIM-4000008G A.1
DOME CAMERA
IK-DP30A
Please read this manual thoroughly before use, and keep it handy
for future reference.
Record in space provided below the Model No. and
the Serial Number as found on the label on the
bottom of the camera.
Model. No. IK-DP30A Serial No.
Retain this information for future reference.
TABLE OF CONTENTS
IMPORTANT SAFEGUARDS................................................ 2
1. Features and description ...........................................
ページ2に含まれる内容の要旨
IMPORTANT SAFEGUARDS 1. Read Instructions 13.Lightning All the safety and operating instructions should be For additional protection on this video product read before the product is operated. during a lightning storm, or when it is left 2. Retain Instructions unattended and unused for long periods of time, The safety instructions and instruction manual unplug it from the wall outlet and disconnect the should be retained for future reference. power supply and cable system. This will prevent 3. He
ページ3に含まれる内容の要旨
• The CAUTION label, shown on the left, is attached on the camera. CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightening flash with arrowhead WARNING : symbol, within an equilateral triangle, TO REDUCE THE RISK OF FIRE OR is intended to alert the user to the ELECTRIC SHOCK, DO NOT EXPOSE presence of uninsulated “dangerous THIS APPLIANCE TO RAIN OR voltage” within the product’s
ページ4に含まれる内容の要旨
1. Features and description Quick Install Design - Cuts Installation Time in Half 480 Lines Horizontal Resolution 400 Degree/Second Pan 18X Optical/12X Digital Zoom Privacy Zone Masking 0.01 Lux Minimum Illumination (1/4, IR Cut filter Off) 50dB Signal-To-Noise Ratio 64 Position Preset Auto-Flip Proportional Zoom 2. Cautions (1) In order to protect the camera, avoid placing or using it under direct sunlight, rain or dust. (2) Avoid touching the zoom lens with your fingers. If necessary, use a so
ページ5に含まれる内容の要旨
35 35 120 120 R19 R19 4. Part names and Locations Control T erminal (RS-422) Power T erminal (24VAC only) Video out BNC connector Installation Brackets (3 Iegs) RS-422 termination switch Dome Base Installation Notch Installation Label Screw for cover Iock Dome Drive (Reserved) X18 Lens 134 134 - 5 - 120 120 173.7 173.7 223.7 223.7
ページ6に含まれる内容の要旨
5. Connections Basic connection (Direct mode) 24V AC UL Iisted class 2 power supply RS422 AC Adaptor (twisted pair line) Monitor Keyboard Make sure to connect to a power supply that allows for at least 35W consumption RS422 Pin Out 2 wire RX - RX+ TX+ controller RX - RX- TX- 2 nd TX - TX+ RX+ Dome Camera TX - TX- RX- In the direct mode the communication line from the keyboard (TX) where TX+ is connected to RX+ of the dome camera and TX- is connected to RX- of the dome camera. If connecting t
ページ7に含まれる内容の要旨
6. Operation (Power On display) When the dome camera powers-up, the software version, selected protocol, and other information are displayed on the TOSHIBA IK-DP30A monitor. VERSION*** PROTOCOL TOSHIBA-P ADDRESS 1 COMM 4800/N/8/1 6.1 ACCESSING THE MENU Accessing the menu varies with the model controller being used. Several controllers are listed below. Please refer to your model's instructions for information on inputting commands. JK-UC1 Input 95 using the numeric keypad. Press the PRESET butto
ページ8に含まれる内容の要旨
6.2 Preset Commands The dome camera can set and perform various preset commands. The following table lists the preset number and whether is can be set (SET) or performed (GO). Presets 1-32 and 35-66 are user presets. Refer to your model's instructions for information on inputting preset commands. Preset Number Function 1-32 SET/GO Preset position 1-32 33 GO Flip 34 GO Home (return to 0 pan position) 35-66 SET/GO Preset position 35-66 70 GO Begin Auto patrol 71 GO Backlight compensation ON 72 GO
ページ9に含まれる内容の要旨
6.4 PERFORMING PRESET OPERATIONS JK-UC1/VLC485 Input the desired preset using the numeric keypad. Press the PRESET button to perform the preset. 6.5 PAN/TILT FUNCTIONS Manual PAN Manual Pan is controlled from a keyboard and the speed ranges from 0.1 degrees/sec to 90 degrees/sec depending on the joystick position. In turbo mode the speed is 150 degree/sec. However, this speed is limited when Proportional P/T is ON. Manual TILT Manual Tilt speed ranges from 0.1 degrees/sec to 45 degrees/sec. Howe
ページ10に含まれる内容の要旨
FRAME SCAN The dome camera can perform a frame scan operation during power-up and by direct control from the keyboard. Operation of zoom and tilt is the same as in Auto Scan. Scan limit stops ARE NOT set: The dome camera will move in 45-degree increments (called stops) horizontally until a manual pan, tilt, or zoom operation is performed from the keyboard. See figure below. stop stop stop 45 stop scan speed stop stop(stop time) stop Scan limit stops ARE set: The dome camera will move in 45-degre
ページ11に含まれる内容の要旨
RANDOM SCAN The dome camera can perform a random scan operation during power-up and by direct control from the keyboard. Operation of zoom and tilt is the same as in Auto Scan. Scan limit stops ARE NOT set: The dome camera will move between random stops and random tilt angles until a manual pan, tilt, or zoom operation is performed from the keyboard. See figure below. E stop D F stop stop 45 C stop stop G stop stop H B stop A ex) A-C-H-E-G-B-D--- Scan limit stops ARE set: The dome camera will mo
ページ12に含まれる内容の要旨
6.7 CAMERA SETUP 6.7.1 FOCUS CONTROL Direct • The focus can be controlled directly using near or far focusing controls. • The focus control has 4 varying speeds. • One Push Trigger Auto Focus. Menu MAIN MENU CAMERA MENU FOCUS MENU MODE AUTO WB ATW ACTIVE TIME 5S INTERVAL TIME 5S ZOOM LIMIT X18 SENSITIVITY NORMAL EXIT SHARPNESS 10 PRIVACY ZONE • The Focus contro
ページ13に含まれる内容の要旨
6.7.2 WHITE BALANCE CONTROL Direct • The White Balance can be set by One Push Trigger operation. Menu MAIN MENU CAMERA MENU WB ATW ZOOM LIMIT X18 EXIT SHARPNESS 10 PRIVACY ZONE The White Balance can be set to ATW (Auto Tracking White)/AUTO/ONE PUSHWB. •ATW automatically adjusts the white balance for color temperatures from 2000K to 10000K. •AUTO automatically adjusts the white balance for color
ページ14に含まれる内容の要旨
MODE • AE mode can be set to FULL AUTO or SHUTTER PRIORITY. • FULL AUTO mode: The shutter is fixed at 1/60 sec and the camera will automatically adjust the iris according to the level. The iris can be controlled manually but will return to FULL AUTO if there is a zoom or pan/ tilt operation. • SHUTTER PRIORITY: The shutter can be varied from 1 sec ?1 /10000 in 22 steps. The camera will automatically adjust the iris according to the level., If the shutter speed is set to 1/1 or 1/2 sec the iris m
ページ15に含まれる内容の要旨
Note At the time of SHUTTER PRIORITY mode choice, DAY/NIGHT mode is fixed in MANUAL. To change the AE options: 1. Enter the preset command to access the main menu. Refer to section 6.1 for the controller model and preset command. 2. Position the cursor ( ) next to CAMERA SETUP and press the OPEN button to access the Camera menu. 3. Position the cursor next to AE and press the OPEN button to access the AE menu. 4. Position the cursor next to the desired option and press the OPEN button to move th
ページ16に含まれる内容の要旨
6.7.5 SHARPNESS Menu MAIN MENU CAMERA MENU WB ATW ZOOM LIMIT X18 EXIT SHARPNESS 10 PRIVACY ZONE The sharpness can be controlled from 0-15, with 15 being the sharpest. To change the SHARPNESS: 1. Enter the preset command to access the main menu. Refer to section 6.1 for the controller model and preset command. 2. Position the cursor ( ) next to CAMERA SETUP and press the OPEN button to access the Cam
ページ17に含まれる内容の要旨
To change the LINE LOCK options: 1. Enter the preset command to access the main menu. Refer to section 6.1 for the controller model and preset command. 2. Position the cursor ( ) next to CAMERA SETUP and press the OPEN button to access the Camera menu. 3. Position the cursor next to LINE LOCK and press the OPEN button to access the Line Lock menu. 4. Position the cursor next to the desired option and press the OPEN button to move the cursor to the right. 5. Move the joystick up or down to select
ページ18に含まれる内容の要旨
Notes: 1) Masking areas are only rectangles. 2) When using the PTZ function the privacy zone expands 2x vertically and 4x horizontally. 3) Although the privacy zone works in digital zoom, the zone setting is only available in a non- digital zoom area. 4) It is recommended to set privacy zone bigger than actual masking area. 5) During turbo panning or tilting, the privacy zone may shift depending on the location of the zone. 6.8 PAN/TILT SETUP 6.8.1 AUTO FLIP The Auto Flip feature allows the tilt
ページ19に含まれる内容の要旨
6.8.2 PROPORTIONAL P/T Proportional P/T controls the pan and tilt speeds according to the amount of zoom. At telephoto settings, the pan and tilt speeds will be slower to keep the image from moving too fast on the monitor. Menu MAIN MENU PAN/TILT MENU AUTO FLIP ON PROPORTIONALP/T ON SCAN LIMIT STOPS OFF MANUAL LIMIT STOPS OFF PARK TIME MIN 0MIN AUTO PATROL P1 OFF EXIT SCAN SPEED 5DEG./S SCAN TILT
ページ20に含まれる内容の要旨
To enable SCAN LIMIT STOPS: 1. Enter the preset command to access the main menu. Refer to section 6.1 for the controller model and preset command. 2. Position the cursor ( ) next to PAN/TILT SETUP and press the OPEN button to access the Pan/ Tilt menu. 3. Position the cursor next to SCAN LIMIT STOPS and press the OPEN button to move the cursor to the right. 4. Move the joystick up or down to select ON or OFF. 5. To accept the selection, press the OPEN button or to cancel the selection, press the
