ページ1に含まれる内容の要旨
INSTRUCTION MANUAL
CCD COLOR CAMERA
IK-VR01A
Please read this manual thoroughly before use, and keep it handy
for future reference.
Record in space provided below the Model No. and
the Serial No. as found on the label on the bottom
of this unit.
Model. No. IK-VR01A Serial No.
Retain this information for future reference.
TABLE OF CONTENTS
Important safeguards
1. Features & Description ................................................. 3
2. Cautions.................................................
ページ2に含まれる内容の要旨
IMPORTANT SAFEGUARDS 1. Read Instructions 13.Lightning All the safety and operating instructions should For added protection for this video product during be read before the product is operated. a lightning storm, or when it is left unattended and 2. Retain Instructions unused for long periods of time, unplug it from The safety instructions and instruction manual the wall outlet and disconnect the power supply should be retained for future reference. and cable system. This will prevent damage to
ページ3に含まれる内容の要旨
• The CAUTION label, shown on the left, is attached on the camera. CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightening flash with arrowhead WARNING : symbol, within an equilateral triangle, TO REDUCE THE RISK OF FIRE OR is intended to alert the user to the ELECTRIC SHOCK, DO NOT EXPOSE presence of uninsulated “dangerous THIS APPLIANCE TO RAIN OR voltage” within the product’s
ページ4に含まれる内容の要旨
1. FEATURES & DESCRIPTION IK-VR01A has the following features: (1) Flush/Surface mount. (2) IP66 Standard for dust and water resistance. (3) Built in vari-focal lens with auto-iris Focal length 3.0~8.0mm. (4) Incorporated 1/3" type CCD image sensor gives high resolution and excellent sensitivity 480 lines horizontal resolution 0.4 lx minimum illumination with tint dome cover (5) 50dB Signal-To Noise Ratio (6) Power supply- AC24V or DC12V - This camera automatically detects the power. (7) BLC, AG
ページ5に含まれる内容の要旨
4. PART NAMES & FUNCTIONS Lens Iris ADJ Mode Setting Switch Counterclockwise: The picture becomes darker. BLC (Backlight Compensation Switch) LL BLC Clockwise: The picture becomes With the switch on, it adjusts ON brighter. the backlight automatically to "Optimum Value" is at default setting. obtain the best possible image. OFF LL Line Lock Phase ADJ Sets camera synchronization Adjusts the phase of the line lock. to line lock with the switch on. Available only with AC24V. Monitor Out Conn
ページ6に含まれる内容の要旨
5. CONNECTIONS AND OPERATIONS Notes on connecting • Power plugs to connected equipment must be disconnected before installation. • A 75-ohm coaxial cable (3C-2V or 5C-2V) is required for standard connection. • For details of wiring and operation of equipment to be connected, refer to their operation manuals. • Coaxial cables for video signals and the power cord are not supplied with the camera. Refer to the operations manuals of connected equipment for detailed wiring and overall operation instr
ページ7に含まれる内容の要旨
5-2 Line-Lock Control • Matching the vertical synchronization with the power frequency is called the Line- Lock. • This function is activated when the LL of Mode Setting Switch is on. • When two or more cameras are switched by the video switcher for viewing by a monitor TV, the vertical sync. phase can be locked with the power frequency, and a stable vertical sync. is obtained without being disturbed at the time of switching. Video Monitor VIDEO SWITCHER CAMERA1 TO AC 24V UL Listed class 2 power
ページ8に含まれる内容の要旨
6. INSTALLATIONS • Connect the cable of the camera and the cable from the designated power supply with respective connectors. • Screws for fixing the camera and mounting base to the ceiling or wall are not supplied with the unit. Use appropriate screws. Note : • The weight (camera body only) is about 1.3kg. The camera unit including the mounting base and the bracket weighs 2.1kg. • When installing to surfaces of other materials, use the screws to fix it firmly. 6-1 Adjust the Angle of View Secur
ページ9に含まれる内容の要旨
Tilt rotation Horizontal rotation a 2 a Tilt Lock FAR ∞ 1 Pan Lock 4 Focus NEAR lock lever WIDE TELE a 3 Zoom Pan Remove three silver lock lever screws transport protection. a Transport Protection Screws (silver) (2) The lens direction in pan direction can be adjusted by turning pan lock 1 counterclockwise to unfasten it without moving the lens. After adjustment, turn pan lock clockwise to fasten it. 1 Note : • Do not turn the lens over 360°. Otherwise the inner connector may be broken and
ページ10に含まれる内容の要旨
46 mm 46 mm 83.5 mm 55 mm 85 mm 83.5 mm 85 mm 55 mm 6-2 Installing the Camera Unit 6-2-1 Installation to Wall or Ceiling with Mounting Base (Surface Mount Installation) Cable access hole ø27 mm • When installing the camera unit on the wall, mount it with the drain groove on C Mounting Base center the downside. Do not block the drain groove. B • When installing the camera unit outdoor, make waterproof for the cables. The camera body is water-resistant but the brackets are not water-resist
ページ11に含まれる内容の要旨
46 mm 83.5 mm 6-2-2 Installation to Junction Box with Bracket (Flush Mount Installation) Junction Box Bracket Screws (not supplied) x4 Note the direction of the bracket, which has two sides. Align the marks. Screws x3 Mount camera base with three supplied screws B. (Shorter screw(M4x10)) Tighten and lock the screws firmly. Mount the top cover (the assembly of the top dome cover) and secure it firmly with three security screws by the supplied special hexangular wrench. Align to this ma
ページ12に含まれる内容の要旨
6-2-3 Change of Dome Cover Screws (x3) Retainer plate Put the protruding side downward. The protruding portion should be set in the groove of the shock damper. Shock damper cushion Note the direction of the damper cushion. The groove should be face up. Dome cover Gasket Top cover Dome replacement When the dome cover is damaged or to be replaced by a transparent cover, call your distributor or sales person. Firmly tighten three mounting screws. Take care not to let dirt or foreign object enter
ページ13に含まれる内容の要旨
7. LINE LOCK PHASE When a video switcher switches two or more cameras, the picture may fluctuate on the video monitor due to the different AC line phase of each camera. In this case, adjust the V PHASE controller to get a stable image. Line Lock V PHASE CONTROL 8. NOTE ON USE AND INSTALLATION • Do not aim the camera at the sun Do not aim the camera at the sun or point it at sun even if you are not shooting. • Do not shoot intense light Intense light such as a spotlight may cause a bloom or smear
ページ14に含まれる内容の要旨
9. IN CASE OF PROBLEMS Condition Check Points No image • Are the camera and connected equipment turned on? • Are cables connected correctly? Unnatural color • Is the monitor TV adjusted correctly? • Is the lighting too weak? The image is out of • Is the lens focus adjusted? focus. • Is the lens or cover dirty? • Are there any large barrier or bright illumination near the The image is dark. camera? • Is the lens iris adjustment volume correctly set? - 13 -
ページ15に含まれる内容の要旨
10.SPECIFICATIONS 1. Image System Image Device 1/3” IT CCD Pixel Elements 771 (H) x 492 (V) 2. Electrical TV System 2:1 Interlace, 15.734KHz Horizontal, 59.94Hz Vertical Horizontal Resolution 480 TV lines S/N Ratio 50dB (TYP. White 100%, Weight On, SC TRAP ON) Minimum Illumination 0.2 lux (More than 10% of image output, Clear dome cover) 0.4 lux (More than 10% of image output, Tint dome cover) Auto Gain Control (AGC) Average AGC (24dB) Iris Control Mode Auto Iris Lens White Balance Auto White Ba
ページ16に含まれる内容の要旨
11. EXTERIOR VIEW unit : mm () 48.5 () 110 () 155 - 15 - SR45.5 ( φ 175 )
ページ17に含まれる内容の要旨
45.5 unit : mm () 150 () 61.5 () 41 () 147.5 - 16 - ( φ 170 )
ページ18に含まれる内容の要旨
Bracket unit : mm 120 46 110 4-M4 4- φ 4.5 4- φ 6.5 Mounting Base 85 46 4.4 20 82 6- φ 5.5 4-M6 Depth=10 4- φ 6.5 φ 27 15 40 15 55 - 17 - 85 120 83.5 83.5 7 15 40 15 114 60
ページ19に含まれる内容の要旨
- 18 -
