ページ1に含まれる内容の要旨
DJLab.3
OWNER'S MANUAL
S TA N T O N MA G N E T IC S , IN C
information@stantondj.com +1 954- 689-8833
w w w . s t a n t o n d j . c o m
ページ2に含まれる内容の要旨
IMPORTANT TO SAFETY 12. 1. Read these Instructions 2. Keep these Instructions Use only with the cart, stand, tripod, 3. Heed all Warnings bracket, or table specified by the 4. Follow all Instructions manufacturer, or sold with the apparatus. When a cart is used, use caution when 5. Do not use this apparatus near water 6. Clean only with dry cloth moving the cart/apparatus combination to 7. Do not block any ventilation openings. Install in avoid injury from tip-over. accordance wit
ページ3に含まれる内容の要旨
LINE VOLTAGE SELECTION 115V 1) The desired voltage of your turntable may be set with the VOLTAGE SELECTOR switch on the rear panel of the main unit, using a screwdriver. 2) Do not twist the VOLTAGE SELECTOR switch with excessive force as this may cause damage. 3) If the VOLTAGE SELECTOR switch does not move smoothly contact a qualified serviceman. 230V M.202 FEATURES 3 band EQ w/ input GAIN control per channel. Power on/off muting. Long-lasting crossfader. Crossfad
ページ4に含まれる内容の要旨
M.202 CONTENTS When used with a compatible CD player, you can use the crossfader to start and stop the CD player with the slide of the fader. The fader start switch activates the fader start feature. When in the ON position, the fader start allows the fader to return automatically to preset digital CUE POINTS on your compatible STANTON DJ CD Player. 14) Mic EQ – The mic channel include a two-band EQ with a range of +10dB to –10dB. 15) Level Indicators – The dual LED indicators
ページ5に含まれる内容の要旨
QUICK SETUP DIAGRAM Study this setup diagram. Make sure all faders are at "zero" and all devices are off. First, connect all input sources. Next, connect your microphone and monitor headphones. Finally, connect the stereo outputs to the power amplifier(s) and/or audio receivers such as tape decks. Plug your mixer into AC power. Now you are ready to switch everything on. IMPORTANT: Always switch on your audio input sources such as turntables or CD players first, then your mixer, and finall
ページ6に含まれる内容の要旨
SPECIFICATIONS M.202 INPUT / OUTPUT IMPEDANCE & SENSITIVITY: LINE -14dB/10K OHM ±2dB PHONO -50dB /47K OHM ±2dB MIC -60dB /2.2K OHM ±2dB MASTER 1K OHM PHONES 0dB/33 OHM ±2dB (LOAD=32 OHM) MAX. OUTPUT (THD=1%) MASTER MORE THAN +14dBV PHONES MORE THAN +21dBV CHANNEL BALANCE WITHIN 3dB FREQUENCY RESPONSE: LINE 20-20KHz ±2dB PHONO 20-20KHz +2, -3dB (RIAA) MIC 20-20KHz +2/-3dB OUTPUT NOISE (IEC-A WEIGHTED) LINE LESS THAN -90dBV PHONO LESS THAN -80dBV MIC LESS THAN
ページ7に含まれる内容の要旨
CONNECTIONS 1) Connect the power cord to an AC outlet. 2) Connect the RCA cable to the PHONO input of your mixer. You can also use a line input by setting the phono/line switch at the rear of the turntable to Line. Note: This turntable has separate analog and digital circuits. If you are looking for a purely analog signal, use the Phono output. For access to the Key Lock feature use the Line output or S/P DIF output. T.80 TURNTABLE CONTENTS
ページ8に含まれる内容の要旨
T.80 TURNTABLE CONTENTS 1) Start/Stop 12) Tonearm 2) Strobe Dots 13) Pitch Select 3) Slipmat 14) Tone Arm Base 4) Center Spindle 15) Counterweight 5) Motor ON/OFF Switch 16) 45-rpm Adaptor Holder 6) Platter Revolution Speeds (RPM) 17) Extra Stylus Holder 7) Target Light Base 18) Reverse 8) Key Lock 19) Phono/Line Output 9) Pitch Lock 20) Phono/Line Switch 10) Pitch Slider 21) Digital Output 11) Headshell Locking Nut 22) Power Cord Connector/Power Switch TONE ARM AND CARTRIDGE SE
ページ9に含まれる内容の要旨
SPECIFICATIONS T.80 POWER SOURCE AC 100V, 50/60Hz (For Japan) AC 110V, 60Hz (For Taiwan) AC 120V, 60Hz (For U.S.A.,Canada,Mexico) AC 220V, 50Hz (For United Arab Emirates,Chile,Argentina) AC 220V, 60Hz (For Philippines) AC 230V, 50Hz (For Europe,New Zealand,South Africa,Singapore,Israel) AC 240V, 50Hz (For Australia,U.K.) POWER CONSUMPTION 10 Watts DIMENSIONS 452 (W) x 370 (D) x 86 (H) mm WEIGHT 8.6 Kgs
ページ10に含まれる内容の要旨
Stanton Magnetics, Inc. – Warranty Provision – Returns for Repairs or Replacement WARRANTY Through Stanton’s authorized dealers around the World, Stanton, or one of Stanton’s authorized distributors outside the U.S., will, without charge, repair or replace, at the sole discretion of the entity responsible for making the repair or providing the replacement, any Stanton merchandise proved defective in material or workmanship for a period of one (1) year following the date of original purcha
ページ11に含まれる内容の要旨
cut along dotted line STANTON WARRANTY REGISTRATION CARD If you have internet access, please register your product at www.stantondj.com. Otherwise, return this card completely filled out in order to validate your warranty. PERSONAL INFO Name Address City State Zip Country Telephone PRODUCT INFO Model Number Serial Number Date of Purchase Where did you buy this product?
ページ12に含まれる内容の要旨
PLACE STAMP HERE Stanton Magnetics, Inc. 3000 SW 42nd Street Hollywood, FL 33312 U.S.A.
