ページ1に含まれる内容の要旨
ページ2に含まれる内容の要旨
GB2 User GB2 User GB2 User GB2 User GB2 User Guide Guide Guide Guide Guide GB2 User Guide 1
ページ3に含まれる内容の要旨
IMPORTANT Please read this manual carefully before using your mixer for the first time. © Harman International Industries Ltd. 2006 All rights reserved Parts of the design of this product may be protected by worldwide patents. Part No. ZM0344-01 Soundcraft is a trading division of Harman International Industries Ltd. Information in this manual is subject to change without notice and does not represent a commitment on the part of the vendor. Soundcraft shall not be liable for any loss or damage w
ページ4に含まれる内容の要旨
Contents Contents Contents Contents Contents Introduction 5 Key Features 6 Warranty 7 Installation 9 SAFETY SYMBOL GUIDE 9 IMPORTANT SAFETY WARNINGS 10 Mains Installation 12 WORKING SAFELY WITH SOUND 14 Setting Up & Troubleshooting 14 Optional External Power Supply 16 Audio Connector Pinouts 17 Dimensions 18 Block Diagrams 19 Input Channels 20 Master Section / Outputs 21 Using The Console 23 Mono Input 24 Stereo Input 26 Master Section 29 Rear Connector Panel 31 Lamps 32 Typical Specifications 3
ページ5に含まれる内容の要旨
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipmentis operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of
ページ6に含まれる内容の要旨
Intr Intr Intr Intr Introduction oduction oduction oduction oduction GB2 User Guide 5
ページ7に含まれる内容の要旨
Key Features Thank you for buying the GB2 mixing console. its main features are: Individually switched 48V phantom power on every mono input module. 6 Aux sends. 4 Group sends (paired). 6 X 2 Output Matrix. New GB30 mic pre-amp. 4-band GB30 EQ. Integral power supply, with an external power supply link option. All metal TRS jacks and Neutrik XLRs. Direct outputs on all mono input channels. 6 GB2 User Guide
ページ8に含まれる内容の要旨
Warranty 1 Soundcraft is a trading division of Harman International Industries Ltd. End User means the person who first puts the equipment into regular operation. Dealer means the person other than Soundcraft (if any) from whom the End User purchased the Equipment, provided such a person is authorised for this purpose by Soundcraft or its accredited Distributor. Equipment means the equipment supplied with this manual. 2 If within the period of twelve months from the date of delivery of the Equip
ページ9に含まれる内容の要旨
8 GB2 User Guide
ページ10に含まれる内容の要旨
Installa Installa Installation tion tion Installa Installation tion For your own safety and to avoid invalidation of the warranty please read this section carefully. SAFETY SYMBOL GUIDE For your own safety and to avoid invalidation of the warranty all text marked with these symbols should be read carefully. WARNINGS The lightning flash with arr The lightning flash with arr The lightning flash with arr The lightning flash with arr The lightning flash with arrowhead symbol, is owhead symbol, is ow
ページ11に含まれる内容の要旨
IMPORTANT SAFETY WARNINGS THIS UNIT MUST BE EARTHED Under no circumstances should the mains earth be disconnected from the mains lead. The wires in the mains lead are coloured in accordance with the following code: Earth: Green and Yellow (Green/Yellow - US) Neutral: Blue (White - US) Live: Brown (Black - US) As the colours of the wires in the mains lead may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured Gree
ページ12に含まれる内容の要旨
WARNINGS • Read these instructions. • Keep these instructions. • Heed all warnings. • Follow all instructions. • This unit contains no user serviceable parts. Refer all servicing to a qualified service engineer, through the appropriate Soundcraft dealer. • Clean the apparatus only with a dry cloth. • Do not install near any heat sources such as radiators, heat resistors, stoves, or other apparatus (including amplifiers) that produce heat. • Do not block any ventilation openings. Ventilation shou
ページ13に含まれる内容の要旨
General Precautions Avoid storing or using the mixing console in conditions of excessive heat or cold, or in positions where it is likely to be subject to vibration, dust or moisture. Do not use any liquids to clean the fascia of the unit: a soft dry cloth is ideal. Avoid using the console close to strong sources of electromagnetic radiation (e.g. video monitors, high-power electric cabling): this may cause degradation of the audio quality due to induced voltages in connecting leads and chassis.
ページ14に含まれる内容の要旨
Initial Wiring Considerations For optimum performance, it is essential for the earthing system to be clean and noise free, as all signals are referenced to this earth. A central point should be decided on for the main earth point system, and all earths should be 'star fed' from this point. It is common electrical practice to `daisy chain' the earths to all electrical outlets but this method is unsuitable for audio installations. The preferred method is to run an individual earth wire from each o
ページ15に含まれる内容の要旨
Points to Remember In all cases, use good quality twin screened audio cable. Check for instability at the output. Always connect both conductors at both ends, and ensure that the screen is only connected at one end. Do not disconnect the mains earth from each piece of equipment. This is needed to provide both safety and screen returns to the system star point. Equipment which has balanced inputs and outputs may need to be electrically isolated from the equipment rack and/or other equipment, to a
ページ16に含まれる内容の要旨
Setting Up & Troubleshooting Initial set-up Once you have connected up your system (see the sections on connection and wiring earlier in this manual for guidance) you are ready to set initial positions for the controls on your mixer. Set up individual input channel as follows: Connect your sources (microphone, keyboard etc.) to the required inputs and release the MUTE switches. Note: Phantom powered mics should be connected before the 48V is switched on. Set Master faders at 0, input faders at
ページ17に含まれる内容の要旨
Meters not showing any signal Has the input gain been set correctly? (see above.) Is the source connected to the appropriate input socket for the level of signal? Do you have something connecetd on the Inserts, and is that external device switched on? Are the Master faders set at max., are input faders set high enough and is the channel routed to the output being monitored? Is the MUTE switch released on the relevant channels? Is the appropriate monitor select switch pressed? Is there a PFL/AFL
ページ18に含まれる内容の要旨
Audio Connector Pinouts GB2 User Guide 17
ページ19に含まれる内容の要旨
Dimensions 18 GB2 User Guide
ページ20に含まれる内容の要旨
Bloc Bloc Block Dia k Dia k Diag g gr r rams ams ams Bloc Block Dia k Diag gr rams ams GB2 User Guide 19
